PIC24FJ128GB410-I/PT - 16-bit 32MHz MCU, 128KB Flash, USB-OTG | Microchip
Teilenummer: PIC24FJ128GB410-I/PT ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $4.92 | $4,92 |
| 10 | $4.43 | $44,30 |
| 100 | $3.94 | $394,00 |
| 500 | $3.55 | $1.775,00 |
| 1.000 | $3.15 | $3.150,00 |
PIC24FJ128GB410-I/PT Übersicht
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, data RAM, and peripherals. The PIC24F family sits in Microchip's 16-bit MCU portfolio between 8-bit PIC18 and 32-bit PIC32MX/dsPIC devices, optimized for ultra-low-power and mixed-signal applications. Microcontrollers belong to the broader category of embedded processors and are the building blocks of nearly every electronic product, from battery-powered IoT nodes to industrial HMI panels.
Key features include 128 KB self-programmable Flash (43K x 24 instruction words), 16 KB SRAM, 4 KB auxiliary Flash for EEPROM emulation, hardware crypto engine, USB-OTG with PHY, segment LCD driver up to 128 segments, 4 UARTS, 4 SPI, 5 I2C, 16-bit timers, 12-bit A/D up to 1 Msps, and CTMU for capacitive measurement. The XLP technology enables nanoWatt deep-sleep currents as low as 20 nA in Sleep mode and 1.8 µA in RTCC mode, making it suitable for battery-powered designs.
The 16-bit modified-Harvard architecture with separate program and data buses enables deterministic interrupt latency and single-cycle 16-bit multiply, while the peripheral pin select (PPS) remapping subsystem simplifies PCB routing. The hardware crypto engine performs AES in 1.6 µs/MB and SHA-256 in 2.6 µs/block, offloading the CPU and reducing firmware complexity.
Typical applications include secure IoT sensor nodes, USB medical devices, secure access control, smart metering with LCD, industrial HMI, and battery-powered data loggers. The integrated USB-OTG PHY enables it to act as either USB host or device without external components.
Design consideration: route VDD/VSS pairs to each pin pair, place a 100 nF decoupling capacitor within 3 mm of every VDD pin, and connect the on-board 32 kHz secondary oscillator pins to a watch crystal for accurate RTCC. The Hardware Crypto module requires firmware initialization before use.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that go beyond what the manufacturer datasheet alone provides.
Drop-in-Alternativen für PIC24FJ128GB410-I/PT – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit PIC24FJ128GB410-I/PT (gleiche Bauform und Footprint) – abweichend in Package, ADC, Operating Temperature, Core Architecture, Program Memory (Flash).
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
PIC24FJ128GA410-I/PT
✅ Drop-In✓ Auf Lager
$3.21 / Stück
Datenblatt ansehen →PIC24FJ256GB410-I/PT
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC24FJ128GB410T-I/PT
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC24FJ128GA610-I/PT
✅ Drop-In✓ Auf Lager
$4.85 / Stück
Datenblatt ansehen →PIC24FJ128GA010-I/PT
✅ Drop-In✓ Auf Lager
$4.95 / Stück
Datenblatt ansehen →PIC24FJ1024GB610-I/BG
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$7.44 / Stück
Datenblatt ansehen →PIC24FJ128GB410-I/PT Grenzwerte & elektrische Eigenschaften
| Core Architecture | PIC24F 16-bit modified-Harvard |
| CPU Speed | 32 MHz (16 MIPS) |
| Program Flash | 128 KB (43K x 24 instruction words) |
| SRAM | 16 KB |
| Auxiliary Flash (EEPROM emulation) | 4 KB |
| Supply Voltage (VDD) | 2.0 V to 3.6 V |
| Hardware Crypto Module | AES, DES, 3DES, SHA-1, SHA-256, MD5, HMAC |
| USB Controller | USB-OTG full-speed with on-chip PHY |
| LCD Driver | Segment LCD, up to 128 segments |
| ADC | 12-bit, up to 1 Msps |
| Comparators | 3 analog comparators |
| UART | 4 |
| SPI | 4 |
| I2C | 5 |
| Timers | 16-bit x 5 |
| RTCC | Real-Time Clock Calendar with 32 kHz crystal support |
| DMA | 8-channel |
| Gehäuse | 100-pin TQFP (PT), 12x12 mm |
| Betriebstemperatur | -40 C to +85 C (industrial) |
| Montageart | Surface Mount |
| MSL-Level | 3 (168 hours) |
| RoHS-Status | Compliant (ROHS3) |
PIC24FJ128GB410-I/PT Pin-Konfiguration
| Pin 1 | RG15/SDA2 — I/O / I2C2 SDA |
| Pin 2 | RC13 — I/O |
| Pin 3 | RC14 — I/O |
| Pin 4 | OSC1/CLKI — Crystal oscillator input or external clock |
| Pin 5 | OSC2/CLKO — Crystal oscillator output |
| Pin 6 | SOSCI/RP13 — Secondary oscillator input / remappable I/O |
| Pin 7 | SOSCO/RP14/T1CK — Secondary oscillator output / remappable I/O / Timer1 clock |
| Pin 8 | MCLR — Master Clear (reset) input, active low |
| Pin 9 | VDD — Positive supply |
| Pin 10 | RA0 — I/O |
| Pin 11 | RA1 — I/O |
| Pin 12 | RA2 — I/O |
| Pin 13 | RA3 — I/O |
| Pin 14 | RA4 — I/O |
| Pin 15 | RA5 — I/O |
| Pin 16 | RA6 — I/O |
| Pin 17 | RA7 — I/O |
| Pin 18 | VSS — Ground reference |
| Pin 19 | RA9 — I/O |
| Pin 20 | RA10 — I/O |
| Pin 21 | RA11 — I/O |
| Pin 22 | RA12 — I/O |
| Pin 23 | RA13 — I/O |
| Pin 24 | RA14 — I/O |
| Pin 25 | RA15 — I/O |
| Pin 26 | RB0 — I/O |
| Pin 27 | RB1 — I/O |
| Pin 28 | RB2 — I/O |
| Pin 29 | RB3 — I/O |
| Pin 30 | RB4 — I/O |
| Pin 31 | RB5 — I/O |
| Pin 32 | RB6 — I/O / ICD PGC |
| Pin 33 | RB7 — I/O / ICD PGD |
| Pin 34 | RB8 — I/O |
| Pin 35 | RB9 — I/O |
| Pin 36 | RB10 — I/O |
| Pin 37 | RB11 — I/O |
| Pin 38 | RB12 — I/O |
| Pin 39 | RB13 — I/O |
| Pin 40 | RB14 — I/O |
| Pin 41 | RB15 — I/O |
| Pin 42 | VSS — Ground |
| Pin 43 | VDD — Positive supply |
| Pin 44 | RC0 — I/O |
| Pin 45 | RC1 — I/O |
| Pin 46 | RC2 — I/O |
| Pin 47 | RC3 — I/O |
| Pin 48 | RC4 — I/O |
| Pin 49 | RC5 — I/O |
| Pin 50 | RC6 — I/O |
| Pin 51 | RC7 — I/O |
| Pin 52 | RC8 — I/O |
| Pin 53 | RC9 — I/O |
| Pin 54 | RC10 — I/O |
| Pin 55 | RC11 — I/O |
| Pin 56 | RC12 — I/O |
| Pin 57 | RD0 — I/O |
| Pin 58 | RD1 — I/O |
| Pin 59 | RD2 — I/O |
| Pin 60 | RD3 — I/O |
| Pin 61 | RD4 — I/O |
| Pin 62 | RD5 — I/O |
| Pin 63 | RD6 — I/O |
| Pin 64 | RD7 — I/O |
| Pin 65 | RD8 — I/O |
| Pin 66 | RD9 — I/O |
| Pin 67 | RD10 — I/O |
| Pin 68 | RD11 — I/O |
| Pin 69 | VSS — Ground |
| Pin 70 | VDD — Positive supply |
| Pin 71 | RD12 — I/O |
| Pin 72 | RD13 — I/O |
| Pin 73 | RD14 — I/O |
| Pin 74 | RD15 — I/O |
| Pin 75 | RE0 — I/O |
| Pin 76 | RE1 — I/O |
| Pin 77 | RE2 — I/O |
| Pin 78 | RE3 — I/O |
| Pin 79 | RE4 — I/O |
| Pin 80 | RE5 — I/O |
| Pin 81 | RE6 — I/O |
| Pin 82 | RE7 — I/O |
| Pin 83 | RF0 — I/O |
| Pin 84 | RF1 — I/O |
| Pin 85 | RF2 — I/O |
| Pin 86 | RF3 — I/O |
| Pin 87 | RF4 — I/O |
| Pin 88 | RF5 — I/O |
| Pin 89 | RF6 — I/O |
| Pin 90 | RF7 — I/O |
| Pin 91 | RF8 — I/O |
| Pin 92 | RF9 — I/O |
| Pin 93 | RF10 — I/O |
| Pin 94 | RF11 — I/O |
| Pin 95 | RF12 — I/O |
| Pin 96 | RF13 — I/O |
| Pin 97 | VSS — Ground |
| Pin 98 | VDD — Positive supply |
| Pin 99 | RG0 — I/O |
| Pin 100 | RG1 — I/O |
Typische Anwendungen
PIC24FJ128GB410-I/PT ist geeignet für 6 Anwendungs: Secure IoT Sensor Nodes, USB Medical Devices, Secure Access Control and Smart Locks, Smart Metering with LCD Display, Industrial HMI Panels, Battery-Powered Data Loggers.
Secure IoT Sensor Nodes
The PIC24FJ128GB410-I/PT fits secure IoT sensor nodes because its integrated hardware crypto engine (AES, SHA-256) offloads TLS handshakes from the 16 MIPS CPU, while the XLP nanoWatt Sleep mode at 20 nA extends battery life to multi-year operation on two AA cells. The 100-pin TQFP exposes 5 I2C and 4 SPI buses, so engineers can connect multiple environmental sensors simultaneously. The 12-bit 1 Msps ADC and 3 comparators enable direct interface to analog sensor front-ends, and the on-chip USB-OTG PHY supports firmware updates over a wired connection. PIC24FJ128GA410-I/PT serves as a lower-cost sibling when hardware crypto is not required.
Empfohlen
USB Medical Devices
The PIC24FJ128GB410-I/PT suits USB medical devices because the integrated USB-OTG full-speed PHY eliminates the need for an external USB transceiver, shrinking BOM cost and PCB area in compact handheld instruments. The hardware AES/SHA-256 engine secures patient data transmitted over USB to a host PC, meeting HIPAA-relevant encryption requirements. The 12-bit ADC with 1 Msps sampling captures bio-signal waveforms (ECG, pulse oximetry) with sufficient resolution for diagnostic algorithms. The industrial -40 to +85 C temperature range and 2.0 V to 3.6 V supply tolerate battery-powered operation. PIC24FJ128GB406-I/MR serves as a smaller-footprint 64-pin variant for ultra-compact probes.
Empfohlen
Secure Access Control and Smart Locks
The PIC24FJ128GB410-I/PT fits secure access control systems because the hardware crypto engine accelerates AES authentication with RFID/NFC readers at the door, while segmented LCD driver (up to 128 segments) drives keypads and status displays directly without external driver ICs. The 32 kHz RTCC with crystal support tracks time-based access schedules, and the nanoWatt Sleep mode (20 nA) lets battery-powered locks idle for years. The 5 I2C instances handle multiple smart-card or BLE modules concurrently. The 100-pin TQFP provides enough GPIO for tamper switches, reed relays, and buzzer outputs. PIC24FJ128GA610-I/PT works as a lower-cost alternative when the LCD segment count is small.
Empfohlen
Smart Metering with LCD Display
The PIC24FJ128GB410-I/PT fits smart electricity/water/gas meters because the integrated segment LCD driver (128 segments) directly drives the meter's display without a separate LCD controller, while the 12-bit ADC at 1 Msps accurately samples current shunts or pulse-output flow sensors. The XLP technology (20 nA Sleep, 1.8 µA RTCC) enables 10+ year battery life on a single lithium cell. The hardware AES-128 engine secures AMI (Advanced Metering Infrastructure) communications over PLC or RF links. The 16 KB SRAM buffers measurement data between transmissions. PIC24FJ128GA310-I/PT serves as a lower-pin-count variant for simpler meters.
Empfohlen
Industrial HMI Panels
The PIC24FJ128GB410-I/PT suits industrial HMI panels because the 100-pin TQFP exposes enough GPIO for matrix keypads, LED status indicators, and segment LCD displays used in operator interfaces. The 4 UARTs handle multi-protocol fieldbus (RS-232, RS-485, Modbus RTU), and the 12-bit ADC reads analog sensor inputs from the controlled process. The hardware crypto engine secures over-the-air firmware updates, critical for field-deployed HMI equipment. The DMA (8-channel) offloads repetitive I/O tasks from the CPU, keeping the 16 MIPS core responsive to user input. PIC24EP512GP806-I/PT serves as an upgrade path for higher-performance HMI.
Empfohlen
Battery-Powered Data Loggers
The PIC24FJ128GB410-I/PT fits battery-powered data loggers because XLP nanoWatt technology reduces Sleep current to 20 nA, allowing multi-year deployment on two AA cells when logging at hourly intervals. The 4 KB auxiliary Flash serves as EEPROM emulation for non-volatile configuration storage, while 128 KB main Flash holds the logger firmware and rolling buffers. The on-chip RTCC with 32 kHz crystal wakes the MCU at scheduled intervals, and the DMA channels move ADC samples to SRAM without CPU intervention. The hardware crypto engine secures logged data against tampering if the logger is recovered. PIC24FJ128GA110-I/PT serves as a smaller variant for low-channel-count loggers.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für PIC24FJ128GB410-I/PT – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | PIC24FJ128GA410-I/PT | PIC24FJ256GB410-I/PT | PIC24FJ128GB410T-I/PT | PIC24FJ128GA610-I/PT | PIC24FJ128GA010-I/PT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 100-pin TQFP (PT) 12x12 mm | 100-pin TQFP (PT) 12x12 mm - same | 100-pin TQFP (PT) 12x12 mm - same | 100-pin TQFP (PT) 12x12 mm - same | 100-pin TQFP (PT) 12x12 mm - same | 100-pin TQFP (PT) 12x12 mm - same |
| Program Flash | 128 KB | 128 KB | 256 KB (+100%) | 128 KB | 128 KB | 128 KB |
| SRAM | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB |
| Hardware Crypto Engine | Yes (AES, DES, SHA-256, MD5) | No | Yes | Yes | No | No |
| USB-OTG PHY | Yes (full-speed) | No | Yes | Yes | No | No |
| Segment LCD Driver | Yes (up to 128 segments) | Yes | Yes | Yes | Yes | No |
| Core Speed | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
Wichtigste Unterscheidungsmerkmale
- Integrated hardware crypto engine (vs. PIC24FJ128GA410-I/PT)
- On-chip USB-OTG full-speed PHY (vs. PIC24FJ128GA610-I/PT)
- Doubling flash for OTA firmware support (vs. PIC24FJ128GB410T-I/PT)
- Segment LCD driver built-in (vs. PIC24FJ128GA010-I/PT)
Designhinweise
Estimated: at 32 MHz core clock with all peripherals active, core current is approximately 19 mA at 3.3 V per Microchip datasheet DS30009983. Place a 100 nF decoupling capacitor within 3 mm of each VDD pin (9, 43, 70, 98) and a single 10 µF bulk capacitor near the MCU. Add a 10 µF + 100 nF pair on the USB VBUS rail if USB-OTG is used. The XLP nanoWatt Sleep mode drops current to 20 nA when peripherals are gated off.
Route the ICSP pair (PGECx/PGEDx) to a 6-pin header with series 4.7 kohm pull-up on MCLR to VDD. Place a 32.768 kHz watch crystal between SOSCI and SOSCO (pins 6 and 7) with 22 pF load capacitors to ground for RTCC accuracy. Use a continuous ground plane under the MCU; route USB D+/D- as a 90:100 ohm differential pair with no splits. Keep the analog AVSS/AVDD pair away from switching signals; the 12-bit ADC needs clean ground.
Do not skip the 100 nF decoupling on every VDD pin - 4 VDD pins means 4 capacitors, not 1. Do not connect USB D+/D- without the 90 ohm differential impedance; this degrades signal integrity and fails USB compliance. Configure the unused oscillator pins as digital I/O rather than analog to avoid excess current draw. Always init the Hardware Crypto engine before first use, and erase auxiliary Flash blocks before writing.
Compliance-Informationen
RoHS3 compliant per Microchip product page and distributor listings (DigiKey, Mouser, Newark). Lead-free finish per JESD97 classification e3. AEC-Q100 not qualified - this is a commercial/industrial grade MCU; Microchip offers separate automotive-grade PIC24 variants for AEC-Q100 designs.
