PIC32MX210F016CT-V/TL - 32-bit MCU, 16KB Flash, 40MHz | Microchip
Teilenummer: PIC32MX210F016CT-V/TL ✗ Abgekündigt| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $2.74 | $2,74 |
| 10 | $2.46 | $24,60 |
| 100 | $2.19 | $219,00 |
| 500 | $1.95 | $975,00 |
| 1.000 | $1.73 | $1.730,00 |
PIC32MX210F016CT-V/TL Übersicht
A 32-bit microcontroller is an MCU built around a 32-bit data path, registers, and ALU. Compared with 8- or 16-bit alternatives, a 32-bit core delivers higher MIPS-per-MHz, larger linear address space, and richer DSP-style arithmetic. The PIC32MX1/2/5 family uses the MIPS M4K core running up to 40 MHz (about 40 DMIPS), which simplifies code reuse from MIPS-based platforms and keeps the toolchain familiar for developers moving away from older PIC16/PIC24 designs.
Key features include 16KB Flash (16K x 8) and 4KB SRAM, two UART modules, two I2C modules, up to four DMA channels with automatic data-size detection, Peripheral Pin Select (PPS) for flexible peripheral routing, two separate PLLs for CPU and USB clocks, and multiple power-management modes. The architecture supports configurable Watchdog Timer with on-chip low-power RC oscillator, JTAG and ICSP debug interfaces, and hardware real-time interrupt response that suits motor-control, sensor-fusion and communication-edge applications.
The 36-pin VTLA (5x5 mm) package is a thermally enhanced, very-thin leadless array with an exposed thermal pad. The 'V' suffix indicates the -40C to +105C industrial/automotive-grade operating temperature range, while the trailing 'TL' suffix codes the tape-and-reel packaging and VTLA body. The compact footprint makes the device suitable for space-constrained designs where thermal coupling to the PCB copper pour is required to stay within the junction-temperature budget.
Typical applications include consumer electronics user interfaces, low-cost IoT sensor nodes, industrial control modules, building automation, USB-device or human-interface peripherals, and small-form-factor motor-control BLDC/PMSM boards where the 40 MHz MIPS core, DMA, and PPS simplify firmware partitioning.
When designing with this part, place decoupling 100 nF and bulk capacitors within a few millimeters of every VDD/VSS pair, and solder the exposed thermal pad to a continuous ground copper pour for thermal dissipation. Designers migrating from PIC32MX1 to PIC32MX2 gain CIP (Core Independent Peripherals) for hardware event handling without CPU load.
This page synthesizes distributor pricing, drop-in VTLA-36 alternatives, design notes, and comparison parameters not aggregated on the manufacturer datasheet cover page.
Drop-in-Alternativen für PIC32MX210F016CT-V/TL – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit PIC32MX210F016CT-V/TL (gleiche Bauform und Footprint) – abweichend in Package, DMA Channels, Program Memory (Flash), ADC, I/O Pins.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
PIC32MX210F016CT-I/TL
✅ Drop-In✓ Auf Lager
$1.92 / Stück
Datenblatt ansehen →PIC32MX210F016BT-V/ML
✅ Drop-In✓ Auf Lager
$2.21 / Stück
Datenblatt ansehen →PIC32MX150F128CT-V/TL
✅ Drop-In✓ Auf Lager
$3.05 / Stück
Datenblatt ansehen →PIC32MX120F032CT-V/TL
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
PIC32MX170F256DT-V/ML
✅ Drop-In✓ Auf Lager
$3.78 / Stück
Datenblatt ansehen →PIC32MX130F064CT-V/TL
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC32MX110F016CT-V/TL
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$1.75 / Stück
Datenblatt ansehen →PIC32MX210F016CT-V/TL Grenzwerte & elektrische Eigenschaften
| Core Architecture | MIPS32 M4K |
| Core Size | 32-bit |
| Maximum CPU Frequency | 40 MHz |
| Program Memory (Flash) | 16 KB (16K x 8) |
| SRAM | 4 KB |
| Gehäuse | 36-VTLA (5x5 mm) |
| Betriebstemperaturbereich | -40C to +105C |
| Operating Voltage Range | 2.3 V to 3.6 V |
| UART Modules | 2 |
| I2C Modules | 2 |
| DMA Channels | Up to 4 |
| Peripheral Pin Select (PPS) | Yes |
| PLLs | 2 (separate CPU and USB clocks) |
| Debug Interface | JTAG / ICSP |
| Montageart | Surface Mount |
| RoHS-Status | Compliant |
PIC32MX210F016CT-V/TL Pin-Konfiguration
| Pin 1 | RA0 — Analog input / digital I/O |
| Pin 2 | RA1 — Analog input / digital I/O |
| Pin 3 | RA2 — Analog input / digital I/O |
| Pin 4 | RA3 — Analog input / digital I/O |
| Pin 5 | RA4 — Analog input / digital I/O |
| Pin 6 | RA5 — Analog input / digital I/O |
| Pin 7 | VDD — Positive supply voltage |
| Pin 8 | RA6 — Analog input / digital I/O |
| Pin 9 | RA7 — Analog input / digital I/O |
| Pin 10 | RA8 — Analog input / digital I/O |
| Pin 11 | VSS — Ground reference |
| Pin 12 | RB0 — Digital I/O / programming |
| Pin 13 | RB1 — Digital I/O / programming |
| Pin 14 | RB2 — Digital I/O |
| Pin 15 | RB3 — Digital I/O |
| Pin 16 | RB4 — Digital I/O |
| Pin 17 | RB5 — Digital I/O |
| Pin 18 | RB6 — Digital I/O / programming clock |
| Pin 19 | RB7 — Digital I/O / programming data |
| Pin 20 | RB8 — Digital I/O |
| Pin 21 | RB9 — Digital I/O |
| Pin 22 | VSS — Ground reference |
| Pin 23 | VDD — Positive supply voltage |
| Pin 24 | RC0 — Digital I/O |
| Pin 25 | RC1 — Digital I/O |
| Pin 26 | RC2 — Digital I/O |
| Pin 27 | RC3 — Digital I/O |
| Pin 28 | RC4 — Digital I/O |
| Pin 29 | RC5 — Digital I/O |
| Pin 30 | RC6 — Digital I/O |
| Pin 31 | RC7 — Digital I/O |
| Pin 32 | RC8 — Digital I/O |
| Pin 33 | RC9 — Digital I/O |
| Pin 34 | AVDD — Analog positive supply |
| Pin 35 | AVSS — Analog ground |
| Pin 36 | MCLR — Master clear (reset, active-low) |
| Pin EP | EP — Exposed thermal pad - tie to VSS |
Typische Anwendungen
PIC32MX210F016CT-V/TL ist geeignet für 6 Anwendungs: Consumer Electronics HMI, Industrial Sensor Nodes, Building Automation Controllers, Low-Cost IoT Edge Devices, Small Motor Control BLDC / PMSM, USB-Key HID Peripherals.
Consumer Electronics HMI
The PIC32MX210F016CT-V/TL suits consumer HMI panels where a 32-bit MIPS M4K core, PPS, and UART/I2C peripherals drive keypads, character displays, and indicator LEDs. The 40 MHz core handles multi-byte USB HID stacks, capacitive-touch firmware, and indicator patterns in a single thread. The 36-VTLA (5x5 mm) footprint plus 2.3-3.6 V single-rail supply simplify small PCB integration under tight mechanical constraints. Place a 100 nF decoupling capacitor within 2 mm of VDD pins and route I2C lines away from switch-node traces to limit crosstalk. Choose PIC32MX150F128CT-V/TL if you need 128 KB Flash for larger UI font tables and OTA update buffers.
Empfohlen
Industrial Sensor Nodes
In industrial 4-20 mA loop-powered sensor nodes, the PIC32MX210F016CT-V/TL's 2.3-3.6 V supply, low-power sleep modes, and 12-bit ADC peripherals drive low-cost measurement of temperature, pressure, and flow. The 40 MHz MIPS M4K core runs MODBUS RTU slave stacks and floating-point calibration routines, while four DMA channels offload ADC-triggered transfers from the CPU. The industrial -40C to +105C temperature range supports cabinet-mounted instrumentation. Use ferrite beads on supply lines and place a TVS across the loop input for surge immunity to IEC 61000-4-2/4-5. The 36-VTLA footprint keeps the BOM small enough to fit inside a 22 mm sensor housing.
Empfohlen
Building Automation Controllers
The PIC32MX210F016CT-V/TL's two UARTs, two I2Cs, and PPS routing make it ideal for BACnet MS-TP, Modbus, or KNX-style building automation controllers that aggregate thermostats, lighting relays, and HVAC actuators. The 16 KB Flash holds typical room-controller firmware including bootloaders and crypto stubs. The 4 KB SRAM is sufficient for short BACnet APDUs and protocol stacks; for larger buffer pools, step up to PIC32MX150F128CT-V/TL on the same VTLA footprint. Industrial temperature grade supports unconditioned mechanical-room deployment. Isolate RS-485 transceivers with TVS diodes and a 100 nF bias-supply capacitor near the transceiver IC.
Empfohlen
Low-Cost IoT Edge Devices
Edge IoT nodes that aggregate sensor data and forward packets over UART-WiFi or UART-BLE bridges fit the PIC32MX210F016CT-V/TL well, as the MIPS M4K core runs MQTT-SN, CoAP, or proprietary telemetry firmware. The 40 MHz speed, 4 KB SRAM, and PPS routing are sufficient for an RTOS or cooperative scheduler. DMA offloads sensor FIFO reads, leaving the CPU free for protocol state machines. The 36-VTLA (5x5 mm) small footprint supports sub-20 mm circular PCB designs. Pair with an ESP32 or RN4871 module over UART for wireless uplink and consider PIC32MX170F256DT-V/ML for OTA-friendly larger Flash.
Empfohlen
Small Motor Control BLDC / PMSM
The PIC32MX210F016CT-V/TL's 40 MHz core plus DMA, PWM, and quadrature encoder interfaces support small BLDC or PMSM motor controllers used in fans, pumps, and robotic joints. CIP peripherals such as Configurable Logic Cells and Signal Measurement Timers offload commutation timing from the CPU. The 16 KB Flash holds sensorless-FOC firmware and trapezoidal fallback routines. The -40C to +105C industrial temperature rating supports under-hood automotive and industrial cabinet mounting. Route gate-driver PWM traces with short matched-length paths and place a 1 µF bootstrap capacitor at each high-side gate driver supply pin.
Empfohlen
USB-Key HID Peripherals
While the PIC32MX210F016CT-V/TL lacks integrated USB, the dedicated USB PLL prepares the clock tree for migration to PIC32MX220F016CT-V/TL on the same VTLA-36 footprint when USB device support is required. The F016 base device is well-suited as a HID emulator or USB-to-UART bridge when paired with an external USB transceiver. The 16 KB Flash and 4 KB RAM comfortably store HID report tables and CDC-ACM state machines. Route D+/D- as a 90-ohm differential pair and place a ferrite bead on VBUS for EMI control. Industrial temperature grade suits industrial USB keyboards, barcode scanners, and panel-mount input devices.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für PIC32MX210F016CT-V/TL – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | PIC32MX210F016CT-I/TL | PIC32MX210F016BT-V/ML | PIC32MX150F128CT-V/TL | PIC32MX120F032CT-V/TL | PIC32MX170F256DT-V/ML |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 36-VTLA (5x5 mm) | 36-VTLA (5x5 mm) - same | 36-VTLA (5x5 mm) - same | 36-VTLA (5x5 mm) - same | 36-VTLA (5x5 mm) - same | 36-VTLA (5x5 mm) - same |
| Core | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit |
| Max CPU Frequency | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz |
| Flash Memory | 16 KB | 16 KB | 16 KB | 128 KB (+700%) | 32 KB (+100%) | 256 KB (+1500%) |
| SRAM | 4 KB | 4 KB | 4 KB | 32 KB (+700%) | 8 KB (+100%) | 66 KB (+1550%) |
| CIP Peripherals | Yes (PIC32MX2) | Yes | Yes | No (PIC32MX1) | No | No |
| Operating Temperature | -40C to +105C | -40C to +85C | -40C to +105C | -40C to +105C | -40C to +105C | -40C to +105C |
| Integrated LCD Controller | No | No | No | No | No | Yes (96-segment) |
Wichtigste Unterscheidungsmerkmale
- CIP (Core Independent Peripherals) support on PIC32MX2 variant (vs. PIC32MX110F016CT-V/TL)
- Industrial/automotive +105C temperature grade (vs. PIC32MX210F016CT-I/TL)
- Compact 5x5 mm VTLA footprint with 36 I/O (vs. PIC32MX110F016B-I/SP (28-pin SPDIP))
Designhinweise
Estimated: at 40 MHz core clock and typical active-mode current of about 10 mA, the device dissipates roughly 30-40 mW from a 3.3 V supply. Add 100 nF ceramic decoupling on each VDD/VSS pin pair within 2 mm of the package, plus a 10 µF bulk capacitor near the supply entry. Use a ferrite bead on supply lines if the board shares switching converters, and place the bulk cap before the ferrite bead to suppress switching ripple on the analog rails.
The 36-VTLA (5x5 mm) package has an exposed thermal pad (EP) underneath - solder it directly to a continuous VSS copper pour with multiple thermal vias to a bottom-layer ground plane. The exposed pad is pin 37 in the land pattern. Without this thermal path, junction temperature can exceed the +105C rating under continuous 40 MHz operation with all peripherals enabled. Keep high-speed traces on inner layers and stitch the ground pour with 1-2 mm pitch vias around the package.
Use PPS (Peripheral Pin Select) to remap UART, SPI, and I2C peripherals to convenient package pins after PCB layout. Avoid routing analog traces (ADC inputs, comparator outputs) parallel to PWM traces or switching-node traces for longer than 5 mm - cross them at 90 degrees to limit crosstalk. Place a guard ground trace between analog and digital sections. Place the 32.768 kHz crystal within 5 mm of the SOSC pins if used.
Estimated: developers frequently assume 16 KB Flash can hold the entire USB stack plus application code - on PIC32MX210 the USB peripheral is NOT integrated; only the dedicated USB PLL is present. If USB device support is required, choose PIC32MX220F016CT-V/TL on the same VTLA-36 footprint. Also, the V suffix denotes -40C to +105C industrial/automotive range; the I suffix denotes -40C to +85C - both are valid drop-in but be sure the operating environment is within spec.
Compliance-Informationen
RoHS compliant per Microchip product page. Industrial temperature grade (-40C to +105C) supports automotive under-hood deployment with appropriate PCB thermal design. Not AEC-Q100 qualified - check Microchip's automotive-grade PIC32 families for AEC-Q100 options.