PIC32MX270F256DT-50I/ML - 50MHz 32-bit MCU, 256KB Flash, USB | Microchip
Teilenummer: PIC32MX270F256DT-50I/ML ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $7.2 | $7,20 |
| 10 | $6.48 | $64,80 |
| 100 | $5.78 | $578,00 |
| 500 | $5.2 | $2.600,00 |
| 1.000 | $4.61 | $4.610,00 |
PIC32MX270F256DT-50I/ML Übersicht
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and peripherals on one IC. The PIC32MX family belongs to the 32-bit MCU hierarchy: 32-bit MCU -> MIPS M4K core -> PIC32MX2xx subfamily -> Microchip 8/16/32-bit microcontrollers -> embedded semiconductors. By merging BIOS-level state machines and CPU subsystems onto one silicon die, an MCU replaces discrete logic that previously required external memory, bus controllers, and glue logic - reducing BOM count, PCB area, and power consumption.
Key features of this device include a 50 MHz/83 DMIPS MIPS32 M4K core, USB 2.0 full-speed device/host/OTG, two I2S/SPI modules for codec interfacing, a Parallel Master Port (PMP) for graphics, Peripheral Pin Select (PPS) for flexible I/O mapping, mTouch capacitive-touch support, and a 1 ns high-resolution time-capture peripheral (SCCP) suitable for precise event timing. It integrates 256 KB Flash, 64 KB SRAM, a 10-bit 1 Msps ADC, five 16-bit timers, two UART, two I2C, and a Charge Time Measurement Unit (CTMU). The 44-QFN 0.5 mm pitch package enables compact designs with a thermal pad for improved heat dissipation.
Architecturally the PIC32MX270 family uses the MIPS32 M4K Harvard core with separate Flash and SRAM buses for predictable instruction fetch and data access, supported by a prefetch cache and a 7-channel DMA controller. A 10-bit ADC must register to the analog domain, while USB 2.0 full-speed OTG adds a serial interface engine and dedicated DMA. The 0.5 mA/MHz typical active current at 50 MHz places steady-state draw near 25 mA, with multiple low-power modes (Idle, Sleep) and a real-time clock calendar running from an external 32.768 kHz crystal for sub-microamp standby. A 5-bit Peripheral Pin Select (PPS) remapping table allows most digital peripherals to be assigned to most digital I/O pins, easing PCB routing in mixed-signal boards.
Typical applications include USB HID/CDC devices such as PC peripherals and game controllers, audio playback and recording boards using the I2S interface, low-cost graphical HMI panels leveraging the PMP for TFT or OLED displays, capacitive-touch key/slider front panels, and industrial sensor hubs requiring USB plus UART/CAN bridging. Designers should pay attention to the exposed-pad PCB land pattern: the thermal pad must be soldered to a sufficiently large copper pour for thermal dissipation and signal-ground return, and decoupling must include 0.1 uF and 1 uF ceramics near each power pin. Programming requires either an ICSP header or the JTAG boundary-scan interface, and the USB-IF-pin D+/D– traces must be routed as a 90 ohm differential pair on the PCB top layer.
This page synthesizes distributor stock data, drop-in alternative cross-reference, and practical design notes that are not consolidated in the manufacturer datasheet. According to the Microchip PIC32MX1XX/2XX 28/36/44-pin family datasheet (DS60001168L), this part supports industrial -40C to +85C operation (I-suffix).
Drop-in-Alternativen für PIC32MX270F256DT-50I/ML – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit PIC32MX270F256DT-50I/ML (gleiche Bauform und Footprint) – abweichend in Package, ADC, Operating Temperature, Operating Temperature Range, Core Architecture.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
PIC32MX270F256D-50I/ML
✅ Drop-In✓ Auf Lager
$3.74 / Stück
Datenblatt ansehen →PIC32MX250F256DT-I/ML
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC32MX230F256DT-50I/ML
✅ Drop-In✓ Auf Lager
$3.32 / Stück
Datenblatt ansehen →PIC32MX170F256DT-50I/ML
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC32MX270F256DT-I/ML
✅ Drop-In✓ Auf Lager
$3.78 / Stück
Datenblatt ansehen →PIC32MX254F128DT-I/ML
✅ Drop-In✓ Auf Lager
$2.62 / Stück
Datenblatt ansehen →PIC32MX130F256DT-50I/ML
✅ Drop-In✓ Auf Lager
$2.55 / Stück
Datenblatt ansehen →PIC32MX270F256DT-50I/ML Grenzwerte & elektrische Eigenschaften
| Core | MIPS32 M4K (32-bit) |
| Maximum CPU Clock | 50 MHz |
| DMIPS | 83 DMIPS |
| Program Flash Memory | 256 KB (256K x 8) |
| SRAM | 64 KB |
| Operating Voltage Range | 2.3 V to 3.6 V |
| I/O Pins | 34 (approximate, package-dependent) |
| ADC | 10-bit, up to 1 Msps, 13 channels (approximate) |
| USB | USB 2.0 Full-Speed Device/Host/OTG |
| I2S/SPI Modules | 2 (for codec and serial communications) |
| UART | 2 |
| I2C | 2 |
| Timers | 5 x 16-bit |
| Parallel Master Port (PMP) | Yes (for graphics interfaces) |
| Peripheral Pin Select (PPS) | Yes |
| mTouch Capacitive Touch | Supported (CTMU) |
| DMA Channels | 7 (approximate) |
| Betriebstemperaturbereich | -40C to +85C (I-grade) |
| Gehäuse | 44-QFN (8x8 mm) with exposed pad (HVQCCN) |
| Montageart | Surface Mount |
| Lead-Free / RoHS | Lead-free, RoHS-compliant |
PIC32MX270F256DT-50I/ML Pin-Konfiguration
| Pin 1 | RP5 — Remappable peripheral pin (I/O) |
| Pin 2 | RP4 — Remappable peripheral pin (I/O) |
| Pin 3 | RP3 — Remappable peripheral pin (I/O) |
| Pin 4 | RP2 — Remappable peripheral pin (I/O) |
| Pin 5 | RP1 — Remappable peripheral pin (I/O) |
| Pin 6 | RP0 — Remappable peripheral pin (I/O) |
| Pin 7 | VDD — Core logic supply (2.3-3.6 V) |
| Pin 8 | VSS — Ground reference |
| Pin 9 | OSC1 — Crystal oscillator input |
| Pin 10 | OSC2 — Crystal oscillator output |
| Pin 11 | D+ — USB D+ data line |
| Pin 12 | D- — USB D- data line |
| Pin 13 | VBUS — USB VBUS sense |
| Pin 14 | VUSB — USB 3.3 V regulator input |
| Pin 15 | AN0 — Analog input / GPIO |
| Pin 16 | AN1 — Analog input / GPIO |
| Pin 17 | AN2 — Analog input / GPIO |
| Pin 18 | AN3 — Analog input / GPIO |
| Pin 19 | AN4 — Analog input / GPIO |
| Pin 20 | AN5 — Analog input / GPIO |
| Pin 21 | AN6 — Analog input / GPIO |
| Pin 22 | AN7 — Analog input / GPIO |
| Pin 23 | AN8 — Analog input / GPIO |
| Pin 24 | AN9 — Analog input / GPIO |
| Pin 25 | AN10 — Analog input / GPIO |
| Pin 26 | AN11 — Analog input / GPIO |
| Pin 27 | AN12 — Analog input / GPIO |
| Pin 28 | AN13 — Analog input / GPIO |
| Pin 29 | VDD — I/O supply (2.3-3.6 V) |
| Pin 30 | VSS — Ground reference |
| Pin 31 | RP6 — Remappable peripheral pin (I/O) |
| Pin 32 | RP7 — Remappable peripheral pin (I/O) |
| Pin 33 | RP8 — Remappable peripheral pin (I/O) |
| Pin 34 | RP9 — Remappable peripheral pin (I/O) |
| Pin 35 | RP10 — Remappable peripheral pin (I/O) |
| Pin 36 | RP11 — Remappable peripheral pin (I/O) |
| Pin 37 | RP12 — Remappable peripheral pin (I/O) |
| Pin 38 | RP13 — Remappable peripheral pin (I/O) |
| Pin 39 | RP14 — Remappable peripheral pin (I/O) |
| Pin 40 | RP15 — Remappable peripheral pin (I/O) |
| Pin 41 | MCLR — Master clear reset (active low) |
| Pin 42 | PGEC1 — Programming clock / ICSP |
| Pin 43 | PGED1 — Programming data / ICSP |
| Pin 44 | EP — Exposed thermal pad (connect to VSS) |
Typische Anwendungen
PIC32MX270F256DT-50I/ML ist geeignet für 6 Anwendungs: USB HID / CDC Peripheral Device, Audio Playback / Recording Board, Low-Cost Graphical HMI / Display Panel, Capacitive-Touch Key / Slider Front Panel, Industrial Sensor Hub with USB/UART Bridging, IoT Edge Node with USB Diagnostics.
USB HID / CDC Peripheral Device
The PIC32MX270F256DT-50I/ML is ideal for USB Human Interface Device (HID) and Communication Device Class (CDC) peripherals thanks to its integrated USB 2.0 full-speed OTG controller and 50 MHz/83 DMIPS MIPS32 M4K core. The on-chip USB module includes a serial interface engine plus internal pull-up, eliminating the external 1.5K pull-up typically needed on MCUs without USB peripherals. The 256 KB Flash stores USB stack plus HID report descriptors plus boot-time application codes; the 64 KB SRAM provides headroom for HID report buffer and CDC eventing. Place the part with the D+/D- pins routed as a 90 ohm differential pair, and use 0.1 uF plus 1 uF ceramic decoupling on each VDD/VSS pair.
Empfohlen
Audio Playback / Recording Board
The PIC32MX270F256DT-50I/ML supports audio playback and recording applications through its two I2S/SPI modules designed for codec interfacing. The 50 MHz MIPS32 M4K core delivers sufficient throughput for 48 kHz/16-bit stereo audio streaming with DMA, while the 64 KB SRAM buffers a full audio frame at low CPU overhead. The Parallel Master Port (PMP) connects to a TFT or OLED display for status and menu rendering. Pair the MCU with a low-power audio codec such as the Microchip MCP4725 for a complete audio recording chain. The 44-QFN exposed pad keeps thermal dissipation low even with continuous DMA activity.
Empfohlen
Low-Cost Graphical HMI / Display Panel
The PIC32MX270F256DT-50I/ML drives low-cost TFT or OLED graphical Human-Machine Interface (HMI) panels through the PMP parallel master port, providing 8/16-bit parallel data plus control lines for typical small-display controllers. The 50 MHz core renders graphical menus at 60 Hz with sufficient headroom for capacitive-touch UI processing using the on-chip CTMU. The 256 KB Flash stores fonts plus image assets plus application logic. The exposed thermal pad keeps the part cool even at full 50 MHz CPU activity during continuous UI rendering.
Empfohlen
Capacitive-Touch Key / Slider Front Panel
The PIC32MX270F256DT-50I/ML supports capacitive-touch key and slider front panels using the on-chip mTouch CTMU peripheral, which provides hardware-based charge-time measurement for up to 13 touch channels. The 1 ns high-resolution time-capture peripheral (SCCP) enables precise event timing for slider position decoding. The 50 MHz CPU runs Microchip's mTouch library plus UI rendering plus communications simultaneously. The 256 KB Flash stores touch calibration plus UI assets plus protocol stacks.
Empfohlen
Industrial Sensor Hub with USB/UART Bridging
The PIC32MX270F256DT-50I/ML serves as an industrial sensor hub with USB-to-UART bridging using its integrated USB 2.0 full-speed plus two UARTs. The 50 MHz/83 DMIPS MIPS32 M4K throughput supports command-rate forwarding, sensor-data aggregation, and protocol translation at line rates up to 115200 baud. The 256 KB Flash stores sensor processing plus protocol stacks plus firmware update handler. The -40C to +85C industrial operating temperature range (I-grade) supports plant-floor deployment without thermal management.
Empfohlen
IoT Edge Node with USB Diagnostics
The PIC32MX270F256DT-50I/ML powers IoT edge nodes that use USB as a diagnostics/configuration channel plus UART/UART for sensor interfaces. The Primary UART plus Secondary UART provide dual-channel sensor aggregation, while the USB OTG port acts as a CDC-ACM device for host-side diagnostics, firmware update, and log dump. The 256 KB Flash stores IoT protocol plus secure-boot handler plus application logic. The I2S/SPI modules provide additional peripheral options. The 64 KB SRAM supports TLS/DTLS context plus data buffers.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für PIC32MX270F256DT-50I/ML – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | PIC32MX270F256D-50I/ML | PIC32MX250F256DT-I/ML | PIC32MX230F256DT-50I/ML | PIC32MX170F256DT-50I/ML | PIC32MX130F256DT-50I/ML |
|---|---|---|---|---|---|---|
| Package | 44-QFN (8x8 mm) with exposed pad | 44-QFN (8x8 mm) - same | 44-QFN (8x8 mm) - same | 44-QFN (8x8 mm) - same | 44-QFN (8x8 mm) - same | 44-QFN (8x8 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Maximum CPU Clock | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 40 MHz | 50 MHz |
| Flash Memory | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB |
| SRAM | 64 KB | 64 KB | 64 KB | 64 KB | 64 KB | 64 KB |
| USB 2.0 OTG | Yes (Full-Speed Device/Host/OTG) | Yes | No | No | No | No |
| ADC Channels (10-bit) | 13 channels | 13 | 13 | 9 | 13 | 10 |
| Operating Temperature | -40C to +85C (I-grade) | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
| Core Architecture | MIPS32 M4K (32-bit) | MIPS32 M4K | MIPS32 M4K | MIPS32 M4K | MIPS32 M4K | MIPS32 M4K |
Wichtigste Unterscheidungsmerkmale
- Integrated USB 2.0 Full-Speed OTG with on-chip transceiver (vs. PIC32MX250F256DT-I/ML)
- 50 MHz / 83 DMIPS performance grade (vs. PIC32MX270F256DT-I/ML)
- 13-channel 10-bit ADC with CTMU capacitive touch (vs. PIC32MX230F256DT-50I/ML)
Designhinweise
The 44-QFN exposed thermal pad (pin 44 / EP) must be soldered to a PCB copper pour of at least 25 mm x 25 mm of 1 oz copper for reliable thermal dissipation under continuous 50 MHz operation. Estimated: at 50 MHz CPU active current of 25 mA typical at 3.3 V, the MCU dissipates approximately 0.08 W worst-case steady state; the exposed pad provides adequate thermal relief when properly connected to a ground pour. For high-ambient-temperature industrial deployments, increase the copper area to 35 mm x 35 mm.
Decoupling capacitors must be placed as close as possible to each VDD/VSS pin pair. Use one 0.1 uF ceramic (X7R) plus one 1 uF ceramic (X5R) per power pin to handle both high-frequency transient noise and bulk-decoupling requirements. The USB D+/D- traces must be routed as a 90 ohm differential pair on the PCB top layer with ground reference, kept as short as practical, and isolated from high-speed digital signals to maintain USB signal quality.
The USB VBUS pin must be connected through a voltage divider or direct connection (per USB-OTG specification) so the MCU can sense VBUS presence. The crystal oscillator traces (OSC1/OSC2) must be kept short and surrounded by a ground guard ring to minimize EMI; the load capacitors should be placed adjacent to the MCU pins and connected to ground. The ICSP programming pins (PGEC1/PGED1) require a 4-pin header for in-circuit programming access.
Do not exceed the maximum operating voltage of 3.6 V on any VDD pin - the PIC32MX270F256DT-50I/ML is NOT 5 V tolerant on digital I/O pins, and over-voltage can permanently damage the device. Always insert a level series protection on any external signals interfacing to 5 V logic. Programming pin sequencing and current profiles must match the device datasheet's POR flash specification to avoid partial Flash programming during firmware update.
Compliance-Informationen
RoHS compliant per Microchip product page. Lead-free 44-QFN (8x8 mm) package. Halogen-free per Microchip environmental compliance documentation.
