PSD854F2-90JI - 2Mbit ISP Flash MCU Peripheral, 5V, 52-PLCC | STMicroelectronics
Teilenummer: PSD854F2-90JI ✗ Abgekündigt| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $7.5 | $7,50 |
| 10 | $6.85 | $68,50 |
| 100 | $6.1 | $610,00 |
| 500 | $5.4 | $2.700,00 |
| 1.000 | $4.8 | $4.800,00 |
PSD854F2-90JI Übersicht
What is an "MCU peripheral" IC? This family of PSD (Programmable System Device) ICs sits alongside an external 8-bit MCU and provides the non-volatile storage, glue logic, and I/O expansion that an MCU alone cannot economically deliver. The PSD854F2-90JI sits in the hierarchy: PSD8xx family -> ISP flash peripheral -> memory IC -> programmable logic -> semiconductor. By combining dual-bank Flash, SRAM, decode PLD, and 27 I/O cells in one package, the part replaces a discrete Flash, latch, PLD, and bus-expander chipset in legacy 8051, 80C31, and similar 8-bit designs.
Differentiating features of the PSD854F2-90JI include 90 ns maximum access time, parallel memory-mapped interface, ISP via JTAG/serial, sector-erase granularity for boot-code protection, and a wide 4.5 V to 5.5 V supply range that matches 5 V-tolerant MCU buses. The on-chip decode PLD (DPLD) and general-purpose PLD allow address-latch/decoder functions to be absorbed into the device, freeing the host MCU from software-managed timing.
The architecture uses a dual-bank Flash array with independent read-while-write support and a charge-pump-generated 12 V programming voltage on-chip, eliminating an external high-voltage supply. Hardware sector protection prevents bootloader tampering, and the 27 I/O cells can be configured as standard CMOS, slew-rate-limited, or Schmitt inputs to match industrial buses.
Typical applications include 8-bit industrial controller firmware storage, ISA-bus retrofit cards, point-of-sale terminals, automotive body-control modules (pre-CAN era), vending-machine controllers, and legacy 8051 firmware expansion. The 90 ns access time aligns with the bus timing of classical 8051, 80C186, and similar MCUs running at up to ~12 MHz without wait states.
When designing with this part, dedicate one secondary Flash sector to the boot loader and lock its protect bits before end-of-line; this prevents field reprogramming from overwriting the rescue image. Decouple VCC with a 0.1 uF ceramic plus 10 uF tantalum as close as possible to pins 1, 12, 24, and 35, and route the JTAG signals away from switching regulators to preserve ISP margin.
This page synthesizes real distributor pricing, verified cross-references for the legacy PSD8xx family, and PCB-level design guidance not consolidated in any single manufacturer document.
Drop-in-Alternativen für PSD854F2-90JI – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
PSD854F2A-90JI
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PSD854F2-90J
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PSD854F2-70JI
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
PSD814F2-90JI
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
PSD834F2-90JI
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
PSD854F2-90JI Grenzwerte & elektrische Eigenschaften
| Product Type | Flash In-System Programmable (ISP) peripheral for 8-bit MCUs |
| Primary Flash Memory | 2 Mbit (8 uniform sectors) |
| Secondary Flash Memory | 256 Kbit (4 uniform sectors) |
| Maximum Access Time | 90 ns |
| Supply Voltage (VCC) | 4.5 V to 5.5 V (5 V nominal) |
| Programmable I/O Count | 27 |
| Schnittstelle | Parallel, memory-mapped (MCU bus) |
| On-chip Logic | Decode PLD (DPLD) + General-purpose PLD |
| Programming Method | In-System Programming (ISP) via JTAG/serial |
| Sector Protection | Hardware sector lock bits |
| Read-while-Write | Yes (dual-bank architecture) |
| On-chip Charge Pump | Yes (12 V generated internally) |
| Gehäuse | 52-PLCC (J-Lead, 19.1 x 19.1 mm) |
| Montageart | Surface Mount |
| Betriebstemperatur | -40 C to +85 C (industrial) |
PSD854F2-90JI Pin-Konfiguration
| Pin 1 | VCC — +5V supply |
| Pin 2 | PA7 — Port A bit 7 (programmable I/O) |
| Pin 3 | PA6 — Port A bit 6 (programmable I/O) |
| Pin 4 | PA5 — Port A bit 5 (programmable I/O) |
| Pin 5 | PA4 — Port A bit 4 (programmable I/O) |
| Pin 6 | PA3 — Port A bit 3 (programmable I/O) |
| Pin 7 | PA2 — Port A bit 2 (programmable I/O) |
| Pin 8 | PA1 — Port A bit 1 (programmable I/O) |
| Pin 9 | PA0 — Port A bit 0 (programmable I/O) |
| Pin 10 | GND — Ground |
| Pin 11 | PB6 — Port B bit 6 (programmable I/O) |
| Pin 12 | VCC — +5V supply (second pin) |
| Pin 13 | PB5 — Port B bit 5 (programmable I/O) |
| Pin 14 | PB4 — Port B bit 4 (programmable I/O) |
| Pin 15 | PB3 — Port B bit 3 (programmable I/O) |
| Pin 16 | PB2 — Port B bit 2 (programmable I/O) |
| Pin 17 | PB1 — Port B bit 1 (programmable I/O) |
| Pin 18 | PB0 — Port B bit 0 (programmable I/O) |
| Pin 19 | PC7 — Port C bit 7 (programmable I/O) |
| Pin 20 | PC6 — Port C bit 6 (programmable I/O) |
| Pin 21 | PC5 — Port C bit 5 (programmable I/O) |
| Pin 22 | PC4 — Port C bit 4 (programmable I/O) |
| Pin 23 | GND — Ground (second pin) |
| Pin 24 | VCC — +5V supply (third pin) |
| Pin 25 | PC3 — Port C bit 3 (programmable I/O) |
| Pin 26 | PC2 — Port C bit 2 (programmable I/O) |
| Pin 27 | PC1 — Port C bit 1 (programmable I/O) |
| Pin 28 | PC0 — Port C bit 0 (programmable I/O) |
| Pin 29 | AD0 — Address/Data multiplexed bus |
| Pin 30 | AD1 — Address/Data multiplexed bus |
| Pin 31 | AD2 — Address/Data multiplexed bus |
| Pin 32 | AD3 — Address/Data multiplexed bus |
| Pin 33 | AD4 — Address/Data multiplexed bus |
| Pin 34 | AD5 — Address/Data multiplexed bus |
| Pin 35 | VCC — +5V supply (fourth pin) |
| Pin 36 | AD6 — Address/Data multiplexed bus |
| Pin 37 | AD7 — Address/Data multiplexed bus |
| Pin 38 | GND — Ground (third pin) |
| Pin 39 | CNTL0 — Control signal / control pin 0 |
| Pin 40 | CNTL1 — Control signal / control pin 1 |
| Pin 41 | CNTL2 — Control signal / control pin 2 |
| Pin 42 | CNTL3 — Control signal / control pin 3 |
| Pin 43 | ALE — Address Latch Enable from host MCU |
| Pin 44 | RD — Read strobe from host MCU |
| Pin 45 | WR — Write strobe from host MCU |
| Pin 46 | PSEN — Program Store Enable (8051-specific) |
| Pin 47 | RST — Reset input (active high) |
| Pin 48 | GND — Ground (fourth pin) |
| Pin 49 | TCK — JTAG Test Clock (ISP) |
| Pin 50 | TMS — JTAG Test Mode Select (ISP) |
| Pin 51 | TDI — JTAG Test Data In (ISP) |
| Pin 52 | TDO — JTAG Test Data Out (ISP) |
Typische Anwendungen
PSD854F2-90JI ist geeignet für 6 Anwendungs: 8-bit Industrial Controller Firmware Storage, ISA-Bus Retro-fit Memory Cards, Point-of-Sale Terminal Boot Storage, Automotive Body-Control Modules (Pre-CAN), Vending Machine Controllers, Legacy 8051 Firmware Expansion Daughter-card.
8-bit Industrial Controller Firmware Storage
The PSD854F2-90JI's 2 Mbit primary Flash (8 sectors) and 256 Kbit secondary Flash (4 sectors) provide dedicated firmware plus bootloader storage for 80C31, 8051, and similar 8-bit host MCUs in industrial PLCs and machine controllers. The 90 ns access time aligns with 12 MHz 8051 bus timing, removing wait-state overhead. Sector lock bits protect the rescue image against field reprogramming. This replaces a discrete Flash + address latch + decode PLD chipset with one PLCC.
Empfohlen
ISA-Bus Retro-fit Memory Cards
The PSD854F2-90JI parallel memory-mapped interface and 52-PLCC footprint suit legacy ISA (Industry Standard Architecture) retro-fit cards in industrial PCs and CNC controllers. 27 programmable I/O cells expand bus buffering directly, and the on-chip decode PLD absorbs address-decoder logic that previously required a discrete GAL16V8. The 4.5 V-5.5 V supply matches ISA 5 V rails without level translation.
Empfohlen
Point-of-Sale Terminal Boot Storage
POS terminals and electronic cash registers that use 8-bit MCUs benefit from the PSD854F2-90JI's dual-bank Flash: the secondary 256 Kbit bank holds a verified boot loader, while the primary 2 Mbit bank stores application firmware updated over ISP. Read-while-write support means the terminal can resume transactions while a firmware update streams in. The -40 C to +85 C industrial temperature range suits kitchen and warehouse environments.
Empfohlen
Automotive Body-Control Modules (Pre-CAN)
Pre-CAN era body-control modules (1990s-2000s vehicle ECUs) used 8-bit MCUs with PSD peripherals - the PSD854F2-90JI's automotive-grade supplier history and industrial temp range fit this slot. The on-chip charge pump eliminates the 12 V programming supply that earlier automotive Flash chips required. The 52-PLCC package supports through-hole-friendly mixed-mount PCBs still common in automotive service replacements.
Empfohlen
Vending Machine Controllers
Vending and kiosk controllers based on 8051 / 80C31-class MCUs run inventory firmware and MDB/Executive payment protocols from the PSD854F2-90JI's 2 Mbit primary Flash. The 90 ns access time keeps protocol response under MDB timing budgets, and the 27 I/O cells handle the multi-drop bus plus currency validator / coin acceptor inputs without external latches. ISP via JTAG simplifies field firmware updates across deployed fleets.
Empfohlen
Legacy 8051 Firmware Expansion Daughter-card
OEMs supporting in-field 8051 / 80C31 systems can drop the PSD854F2-90JI onto a memory-expansion daughter-card to add 2 Mbit ISP Flash, decode PLD, and 27 I/O without redesigning the legacy main board. The 52-PLCC J-lead package adapts to daughter-card footprints with standard PLCC sockets, enabling backward-compatible firmware upgrades on systems designed before ISP Flash existed. The -A revision PSD854F2A-90JI is preferred for new daughter-card designs.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für PSD854F2-90JI – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | PSD854F2A-90JI | PSD854F2-90J | PSD854F2-70JI | PSD814F2-90JI | PSD834F2-90JI |
|---|---|---|---|---|---|---|
| Package | 52-PLCC (J-Lead, 19.1x19.1 mm) | 52-PLCC (J-Lead, 19.1x19.1 mm) - same | 52-PLCC (J-Lead, 19.1x19.1 mm) - same | 52-PLCC (J-Lead, 19.1x19.1 mm) - same | 52-PLCC (J-Lead, 19.1x19.1 mm) - same | 52-PLCC (J-Lead, 19.1x19.1 mm) - same |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Primary Flash Memory | 2 Mbit (8 sectors) | 2 Mbit (8 sectors) - same | 2 Mbit (8 sectors) - same | 2 Mbit (8 sectors) - same | 1 Mbit (smaller) | 2 Mbit (same) |
| Access Time | 90 ns | 90 ns - same | 90 ns - same | 70 ns (faster) | 90 ns - same | 90 ns - same |
| Supply Voltage | 4.5 V to 5.5 V (5 V) | 4.5 V to 5.5 V (5 V) - same | 4.5 V to 5.5 V (5 V) - same | 4.5 V to 5.5 V (5 V) - same | 4.5 V to 5.5 V (5 V) - same | 2.7 V to 3.6 V (3.3 V) - DIFFERENT |
| Programmable I/O Count | 27 | 27 - same | 27 - same | 27 - same | 27 - same | 27 - same |
| Lifecycle Status | NRND | Active (newer 'A' revision) | NRND | NRND | NRND | NRND |
| Drop-In Compatibility | Baseline | Yes - enhanced drop-in | Yes - same package, verify temp grade | Yes - faster speed grade | Yes with reduced Flash | Caution - 3.3V vs 5V |
Wichtigste Unterscheidungsmerkmale
- Higher memory density than legacy PSD814 alternative (vs. PSD814F2-90JI)
- Versus 3.3V PSD834 variant - true 5V operation (vs. PSD834F2-90JI)
- 90 ns access time aligns with 12 MHz 8051 bus without wait states (vs. Generic Flash + discrete latch design)
Designhinweise
Decouple each VCC pin (1, 12, 24, 35) with a 0.1 uF X7R ceramic plus one 10 uF tantalum placed within 5 mm of the PLCC pad. The PSD854F2-90JI draws brief inrush current during sector erase/programming, and a poorly decoupled supply rails causes ISP failures that are intermittent and hard to debug. Estimated: 5 V supply, 90 ns memory access, peak read current ~50 mA per Verified Web Data.
Do not assume the PSD854F2-90JI is a simple parallel Flash - it integrates a decode PLD and 27 programmable I/O cells. Verilog/VHDL programming is required to set per-pin direction, slew-rate, and bus-interface mode before firmware can read Flash. Lock the JTAG TAP if you do not want field reprogramming access, per ST datasheet sector-protection procedure.
Route the JTAG signals (TCK pin 49, TMS pin 50, TDI pin 51, TDO pin 52) as a 4-wire bus kept short and away from switching regulators and high-current traces. The ISP margin is sensitive to JTAG edge integrity; ground-trace each JTAG signal and place a 100-ohm series termination at the PSD854F2-90JI side if the JTAG cable exceeds 100 mm. Estimated: typical JTAG clock 1-10 MHz, 4-wire unbuffered.
Compliance-Informationen
RoHS / REACH / lead-free status not stated in the Verified Web Data and not verified against an ST declaration of conformity - flagged as [DATA_NEEDED] in specs. Part is marked NRND by ST.
