S912XEG128BMAA - 16-bit 50MHz S12X MCU 128KB Flash | NXP
Teilenummer: S912XEG128BMAA ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $18.5 | $18,50 |
| 10 | $16.2 | $162,00 |
| 100 | $13.75 | $1.375,00 |
| 500 | $11.4 | $5.700,00 |
| 1.000 | $9.85 | $9.850,00 |
S912XEG128BMAA Übersicht
What is an HCS12X microcontroller? The HCS12X is NXP's enhanced 16-bit CISC microcontroller family derived from the original HC12 architecture, augmented with the XGATE peripheral co-processor - an independent RISC-like engine that offloads interrupt-driven tasks from the main CPU to boost effective system throughput. Within the broader hierarchy, the S912XEG128BMAA sits as a Flash-based MCU -> 16-bit microcontroller -> automotive microcontroller -> embedded processor, where it bridges low-cost 8-bit designs and higher-end 32-bit automotive microcontrollers.
Key features include 128 KB of Flash with hardware-emulated EEPROM capability, system integrity via a Memory Protection Unit (MPU) and supervisor/user modes, an Enhanced Capture Timer (ECT), Periodic Interrupt Timer (PIT), Real-Time Interrupt (RTI), Pulse Width Modulation (PWM) outputs, and on-chip Low-Voltage Detection (LVD) and Power-On Reset (POR). The wide supply range (3.3 V / 5 V dual-voltage operation simplify migration between classic and emerging parts.
From an architectural standpoint, the dual-core CPU/XGATE topology lets the main S12X core handle application logic while XGATE services high-speed peripherals such as CAN message buffering and PWM updates, reducing main-CPU interrupt overhead. The 50 MHz bus, 12-bit ADC, and CAN interface together enable deterministic closed-loop control typical of body-electronics modules.
Typical applications include automotive body controllers, instrument clusters, HVAC climate control, sensor conditioning, and industrial CAN nodes. The automotive-grade qualification (AEC-Q100 context) supports deployment under hood and in cabin.
When designing with this MCU, allocate sufficient decoupling (100 nF plus 4.7 µF bulk) near the supply pins and follow NXP's AN128-Q-B-S application note guidance for PCB layout. The XGATE firmware must be loaded into a reserved Flash region, so plan the linker map accordingly.
This page synthesizes verified distributor pricing, pin-compatible alternatives, and design notes not duplicated on the manufacturer datasheet, providing a single, citable engineering reference.
Drop-in-Alternativen für S912XEG128BMAA – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit S912XEG128BMAA (gleiche Bauform und Footprint) – abweichend in Package, Operating Temperature, ADC, Timers, Connectivity.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
MC9S12XEG128MAA
✅ Drop-In✓ Auf Lager
$8.9 / Stück
Datenblatt ansehen →S912XEG256J2CAL
✅ Drop-In✓ Auf Lager
$15.4 / Stück
Datenblatt ansehen →S912XEG384J2VAL
✅ Drop-In✓ Auf Lager
$17.8 / Stück
Datenblatt ansehen →MC9S12XEQ384CAG
✅ Drop-In✓ Auf Lager
Preis auf Anfrage
Datenblatt ansehen →MC9S12XDT256CAG
✅ Drop-In✓ Auf Lager
$17.4 / Stück
Datenblatt ansehen →MC9S12XDT512MAA
✅ Drop-In✓ Auf Lager
Preis auf Anfrage
Datenblatt ansehen →S912XEG128BMAA Grenzwerte & elektrische Eigenschaften
| Core Processor | HCS12X |
| Core Size | 16-bit |
| Core Architecture | CISC with XGATE co-processor |
| Operating Frequency (Bus Speed) | 50 MHz |
| Program Memory Size | 128 KB (128K x 8) Flash |
| Program Memory Type | Flash with hardware-emulated EEPROM |
| EEPROM (Emulated) | Up to 4 KB (hardware-emulated) |
| Number of I/O Pins | 59 |
| Versorgungsspannung | 3.3 V / 5 V dual-voltage |
| Betriebstemperaturbereich | -40 °C to +125 °C (automotive grade) |
| Gehäuse | 80-QFP (14x14 mm), PQFP, tray |
| Connectivity | CANbus, EBI/EMI, I²C, IrDA, SCI, SPI |
| ADC | 12-bit, 3 µs conversion time |
| Peripherals | LVD, POR, PWM, WDT, ECT, PIT, RTI |
| Montageart | Surface Mount (gull-wing leads) |
| MSL-Level | 3 (per JEDEC J-STD-020, typical for QFP) |
| RoHS-Status | Compliant |
| AEC-Q100 Qualification | Automotive qualified |
S912XEG128BMAA 80-qfp (14x14 mm), pqfp, tray Pinbelegungsleitfaden
Pinbelegung für S912XEG128BMAA (80-qfp (14x14 mm), pqfp, tray-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für S912XEG128BMAA.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
S912XEG128BMAA ist geeignet für 6 Anwendungs: Automotive Body Control Module (BCM), Instrument Cluster Controller, HVAC Climate Control Module, Industrial CAN Sensor Node, Chassis Sensor Interface Module, Automotive Lighting Controller.
Automotive Body Control Module (BCM)
The S912XEG128BMAA's 50 MHz S12X core with XGATE co-processor makes it a strong fit for automotive BCMs that aggregate lighting, door-lock, wiper, and accessory switching. Its 59 I/O pins directly drive relays and MOSFET gate drivers without external I/O expanders, while the integrated CANbus controller links the BCM to the vehicle network at 500 kbit/s body baud rates. Hardware-emulated EEPROM at 128 KB Flash holds the BCM application plus non-volatile configuration and diagnostics. Per the NXP datasheet, the -40 °C to +125 °C automotive temperature range and AEC-Q100 qualification enable under-dash mounting. The XGATE offloads CAN message buffering so the main CPU can run BCM logic deterministically, reducing interrupt latency and jitter for time-critical lighting sequences.
Empfohlen
Instrument Cluster Controller
The S912XEG128BMAA drives automotive instrument clusters with its 12-bit / 3 µs ADC accurately sampling fuel-level, temperature, and battery-voltage sensors at refresh rates up to 100 kS/s aggregate. The Enhanced Capture Timer (ECT) precisely measures speedometer and tachometer pulse trains from Hall sensors, while PWM outputs drive analog gauge stepper-motor or pointer drivers. The 50 MHz CPU throughput supports cluster graphics rendering on external LED or segment drivers. Per NXP documentation, the hardware-emulated EEPROM preserves odometer and trip data through power cycles - a regulatory requirement. XGATE offloads display-refresh tasks so the main core runs diagnostic and CAN-communication logic without display glitches.
Empfohlen
HVAC Climate Control Module
Climate-control modules leverage the S912XEG128BMAA's ECT for PWM-driven blower-motor speed control, 12-bit ADC for cabin and evaporator temperature sensing, and SCI/SPI for actuator and stepper-motor driver communication. The S12X core at 50 MHz runs the closed-loop PID control algorithm at 50 Hz loop rates, while XGATE services the CANbus for body-network integration. Per the datasheet, the integrated PWM channels (8-bit or 16-bit resolution selectable) handle mixed blower, mode-door, and blend-door actuation without external timers. The -40 °C to +125 °C temperature range supports engine-bay or cabin mounting depending on vehicle architecture. Hardware-emulated EEPROM stores user climate preferences across battery-disconnect events.
Empfohlen
Industrial CAN Sensor Node
The S912XEG128BMAA serves industrial sensor-hub applications where the CANopen or DeviceNet protocol stack fits within 128 KB of Flash. The integrated CAN controller, combined with the XGATE peripheral engine, sustains deterministic 1 Mbit/s CAN throughput for synchronized distributed I/O nodes. Per the datasheet, the ECT captures encoder feedback, the 12-bit ADC digitizes 4-20 mA or 0-10 V sensor inputs, and SPI interfaces to digital sensors or FRAM. The -40 °C to +125 °C temperature range supports outdoor cabinet installation, while AEC-Q100 qualification provides headroom for harsh industrial environments. Hardware-emulated EEPROM retains calibration constants and node-ID without external storage.
Empfohlen
Chassis Sensor Interface Module
Wheel-speed, steering-angle, and ride-height sensors feed automotive chassis modules built around the S912XEG128BMAA, leveraging its ECT for precise pulse-train measurement and CANbus for chassis-network communication. The 12-bit ADC digitizes ride-height and brake-pressure sensors, while PWM outputs drive active suspension actuators. Per NXP documentation, XGATE offloads the high-rate wheel-speed pulse counting so the main core runs vehicle-dynamics logic without missing edges. The 80-QFP package suits PCB layouts constrained by tight chassis-module enclosures. Hardware-emulated EEPROM stores sensor calibration data through battery disconnects, and the automotive temperature range supports engine-bay or wheel-well mounting.
Empfohlen
Automotive Lighting Controller
Exterior lighting controllers benefit from the S912XEG128BMAA's 59 I/O pins and integrated PWM channels for driving LED matrix headlamps, tail lamps, and indicator modules. The S12X core runs lighting-pattern algorithms while XGATE services the CANbus body-network for lighting command reception. Per the datasheet, the 12-bit ADC monitors string-current feedback for open-LED and short-circuit diagnostics - a regulatory requirement in many markets. The -40 °C to +125 °C range supports engine-bay or headlamp-mounted PCBs, and AEC-Q100 qualification ensures long-term reliability under thermal cycling. Hardware-emulated EEPROM stores per-variant lighting configuration data without external memory.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für S912XEG128BMAA – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | MC9S12XEG128MAA | S912XEG256J2CAL | S912XEG384J2VAL | MC9S12XEQ384CAG | MC9S12XDT256CAG | MC9S12XDT512MAA |
|---|---|---|---|---|---|---|---|
| Package | 80-QFP (14x14) | 80-QFP (14x14) - same | 80-QFP (14x14) - same | 80-QFP (14x14) - same | 80-QFP (14x14) - same | 80-QFP (14x14) - same | 80-QFP (14x14) - same |
| Brand | NXP Semiconductors | NXP Semiconductors (Freescale legacy) | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Flash Size | 128 KB | 128 KB | 256 KB | 384 KB | 384 KB | 256 KB | 512 KB |
| CPU Core | S12X + XGATE | S12X + XGATE | S12X + XGATE | S12X + XGATE | S12X + XGATE (EQ enhanced) | S12X + XGATE | S12X + XGATE |
| Bus Frequency | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz |
| Operating Temperature | -40 °C to +125 °C | -40 °C to +125 °C | -40 °C to +125 °C | -40 °C to +125 °C | -40 °C to +85 °C (commercial - verify) | -40 °C to +85 °C (verify) | -40 °C to +125 °C |
| Automotive Qualified | Yes (AEC-Q100) | Yes | Yes | Yes | Yes | Yes | Yes |
| Connectivity | CAN, EBI/EMI, I²C, IrDA, SCI, SPI | CAN, EBI/EMI, I²C, IrDA, SCI, SPI | Same set | Same set | Same set | Same set | Same set |
Wichtigste Unterscheidungsmerkmale
- Dual-core S12X + XGATE architecture in 80-QFP (vs. MC9S12DT128MPVE)
- Hardware-emulated EEPROM eliminates external memory (vs. MC9S12XDT256CAG (256 KB Flash, separate EEPROM))
- Pin-compatible Flash upgrade path to 256 KB and 384 KB (vs. MC9S12DT128MPVE (older DT family))
Designhinweise
Decouple the S912XEG128BMAA supply pins with a 100 nF ceramic capacitor placed within 5 mm of each VDD pin and a 4.7 µF bulk tantalum or ceramic on the analog supply rail (VDDA). The datasheet recommends separate analog and digital ground returns tied at a single point under the MCU. Inrush current during Flash programming peaks at 30 mA per VDD pair, so bulk-cap sizing must support programming-mode transients without rail collapse.
Route the external crystal/oscillator traces symmetrically within 5 mm of the MCU EXTAL/XTAL pins, surrounded by a guard ring tied to ground to minimize EMI coupling. The XGATE peripheral engine issues high-priority interrupts, so place the MCU away from switching-power noise sources and route noisy traces (PWM, CAN) on the opposite side of the PCB. Keep ADC analog traces short and away from digital switching to preserve 12-bit ADC accuracy.
A common pitfall when bringing up the S912XEG128BMAA is forgetting to initialize the COP (computer operating properly) watchdog before the first application loop. Enable the watchdog in the startup code immediately after oscillator stabilization, then service it in the main loop at least every 1 ms. Another pitfall is neglecting the Memory Protection Unit (MPU) configuration, which can accidentally lock out Flash regions during development. Always program the MPU last after the application firmware is verified, and keep a back-door key sequence for field recovery.
For CANbus signals, place a 120 Ω termination resistor only at the cable ends - not at every node - to avoid bus loading. Use twisted-pair wiring and keep stub lengths below 1/10 of the bit-cell length for 1 Mbit/s operation. For SPI buses running above 4 MHz, add a 33 Ω series damping resistor at the source end to control ringing, and verify setup/hold margins with an oscilloscope across the automotive temperature range.
Compliance-Informationen
RoHS compliance and AEC-Q100 automotive qualification confirmed by NXP product page and distributor listings (DigiKey, Mouser) as of 2026-10-19. Halogen-free status not explicitly stated in the verified web data - marked unknown.
