STM32L072CZT6 - 192KB Flash Cortex-M0+ MCU | STMicroelectronics
Teilenummer: STM32L072CZT6 ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $6.12 | $6,12 |
| 10 | $5.42 | $54,20 |
| 100 | $4.75 | $475,00 |
| 500 | $4.21 | $2.105,00 |
| 1.000 | $3.78 | $3.780,00 |
STM32L072CZT6 Übersicht
An ARM Cortex-M0+ microcontroller (MCU) is a 32-bit RISC processor core from ARM's Cortex-M family optimized for energy efficiency and deterministic interrupt response in deeply embedded systems. The Cortex-M0+ sits at the low-power end of the Cortex-M lineup (Cortex-M0+ -> Cortex-M0 -> Cortex-M3/M4/M33), and STM32L0 microcontrollers sit at the low-power end of the STM32 product hierarchy (STM32L0 -> STM32L1/L4/L5 -> STM32F/G/H families). L0-series MCUs target coin-cell, sensor, metering, and wearable designs where standby current and integrated analog peripherals matter more than raw compute throughput.
Key features of the STM32L072CZT6 include 192 KB Flash with ECC, 20 KB SRAM, a 12-bit ADC with hardware oversampling, two ultra-low-power comparators, a real-time clock, multiple timers, and a USB 2.0 full-speed device interface that operates without an external crystal. The device supports AES-128 hardware encryption for secure connectivity in IoT endpoints. Integrated peripherals include I2C, SPI, USART, USB, and capacitive-touch sensing I/Os.
The architecture combines a Cortex-M0+ core with ST's ultra-low-power design techniques, including multiple voltage domains, low-power RTC, and a wide set of GPIOs tolerant to 5 V. The 48-pin LQFP package balances compact board footprint with easy hand-soldering and breadboard prototyping, and supports the full STM32L072xx peripheral set on the available I/O count.
Typical applications include battery-powered IoT sensors, USB-connected wearables, smart metering endpoints, wireless sensor nodes, medical patch devices, asset trackers, and human-machine interface panels. Designers value the part for USB connectivity in small form factors, deep-sleep currents, and an established STM32 toolchain (STM32CubeIDE, HAL/LL libraries). When designing with this part, plan decoupling around the 1.2 V core regulator pin and verify the low-power mode transitions in your application firmware before committing to battery-life calculations.
Drop-in-Alternativen für STM32L072CZT6 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit STM32L072CZT6 (gleiche Bauform und Footprint) – abweichend in ADC, Communication Interfaces, Core, Timers.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
STM32L073CZT6
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
STM32L072CZT3
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
STM32L072CZT6D
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
STM32L053CZT6
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
STM32L083CZT6
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
STM32L072CZT6 Grenzwerte & elektrische Eigenschaften
| Core | ARM Cortex-M0+ (32-bit) |
| Maximale Taktfrequenz | 32 MHz |
| Flash Memory | 192 KB |
| SRAM | 20 KB |
| Supply Voltage (VDD) | 1.65 V to 3.6 V |
| Supply Voltage (BOR enabled) | 1.8 V to 3.6 V |
| Betriebstemperatur | -40 C to +85 C (grade 6) |
| Gehäuse | 48-pin LQFP (7x7 mm) |
| Montageart | Surface Mount |
| USB | USB 2.0 full-speed device (crystal-less) |
| ADC | 12-bit, hardware oversampling |
| Comparators | 2 ultra-low-power comparators |
| Timers | Multiple 16-bit and 32-bit timers (see datasheet) |
| Communication Interfaces | I2C, SPI, USART, USB |
| AES Hardware | AES-128 |
| RTC | Yes, with calendar and tamper |
| I/Os | Up to 37 GPIOs (package-dependent) |
| RoHS-Status | Compliant |
STM32L072CZT6 Pin-Konfiguration
| Pin 1 | PB9 — GPIO PB9 / I2C1_SDA |
| Pin 2 | PB10 — GPIO PB10 / I2C2_SDA |
| Pin 3 | PB11 — GPIO PB11 / I2C2_SCL |
| Pin 4 | VDD — Digital supply voltage |
| Pin 5 | PB12 — GPIO PB12 / SPI2_NSS |
| Pin 6 | PB13 — GPIO PB13 / SPI2_SCK |
| Pin 7 | PB14 — GPIO PB14 / SPI2_MISO |
| Pin 8 | PB15 — GPIO PB15 / SPI2_MOSI |
| Pin 9 | PA8 — GPIO PA8 |
| Pin 10 | PA9 — GPIO PA9 / USART1_TX |
| Pin 11 | PA10 — GPIO PA10 / USART1_RX |
| Pin 12 | PA11 — GPIO PA11 / USB_DM |
| Pin 13 | PA12 — GPIO PA12 / USB_DP |
| Pin 14 | PA13 — GPIO PA13 / SWDIO |
| Pin 15 | VSS — Digital ground |
| Pin 16 | VDD — Digital supply voltage |
| Pin 17 | PA14 — GPIO PA14 / SWCLK |
| Pin 18 | PA15 — GPIO PA15 / JTDI |
| Pin 19 | PB3 — GPIO PB3 / JTDO |
| Pin 20 | PB4 — GPIO PB4 / NJTRST |
| Pin 21 | PB5 — GPIO PB5 |
| Pin 22 | PB6 — GPIO PB6 / I2C1_SCL |
| Pin 23 | PB7 — GPIO PB7 / I2C1_SDA |
| Pin 24 | PB8 — GPIO PB8 |
| Pin 25 | VSS — Digital ground |
| Pin 26 | VDD — Digital supply voltage |
| Pin 27 | PC13 — GPIO PC13 / RTC_TAMP |
| Pin 28 | PC14 — GPIO PC14 / OSC32_IN |
| Pin 29 | PC15 — GPIO PC15 / OSC32_OUT |
| Pin 30 | VSS — Digital ground |
| Pin 31 | VDDA — Analog supply voltage |
| Pin 32 | VREF+ — ADC reference voltage |
| Pin 33 | PA0 — GPIO PA0 / ADC_IN0 |
| Pin 34 | PA1 — GPIO PA1 / ADC_IN1 |
| Pin 35 | PA2 — GPIO PA2 / ADC_IN2 / USART2_TX |
| Pin 36 | PA3 — GPIO PA3 / ADC_IN3 / USART2_RX |
| Pin 37 | PA4 — GPIO PA4 / ADC_IN4 |
| Pin 38 | PA5 — GPIO PA5 / ADC_IN5 |
| Pin 39 | PA6 — GPIO PA6 / ADC_IN6 |
| Pin 40 | PA7 — GPIO PA7 / ADC_IN7 |
| Pin 41 | PC0 — GPIO PC0 / ADC_IN10 |
| Pin 42 | PC1 — GPIO PC1 / ADC_IN11 |
| Pin 43 | PC2 — GPIO PC2 / ADC_IN12 |
| Pin 44 | PC3 — GPIO PC3 / ADC_IN13 |
| Pin 45 | VSSA — Analog ground |
| Pin 46 | VREF- — ADC reference ground |
| Pin 47 | VSS — Digital ground |
| Pin 48 | VDD — Digital supply voltage |
Typische Anwendungen
STM32L072CZT6 ist geeignet für 6 Anwendungs: Battery-Powered IoT Sensor Nodes, USB-Connected Wearable Devices, Smart Metering Endpoints, Medical Patch and Health Monitoring Devices, Asset Tracking and Cold-Chain Loggers, Human-Machine Interface Panels.
Battery-Powered IoT Sensor Nodes
The STM32L072CZT6 fits battery-powered IoT sensor nodes because of its sub-microamp Standby current (sub-uA) and 192 KB Flash for sensor-stack firmware. Its 32 MHz Cortex-M0+ core is fast enough for periodic sensor sampling while sleeping deeply between events, which directly extends CR2032 coin-cell life. According to the ST datasheet, Stop mode with RTC draws less than 1 uA, enabling multi-year battery deployments for environmental sensors.
Empfohlen
USB-Connected Wearable Devices
The STM32L072CZT6 is well matched to USB-connected wearables because of its crystal-less USB 2.0 full-speed device interface and 192 KB Flash for vendor-class USB stacks. Designers save a 48 MHz crystal and reduce BOM cost while maintaining USB compliance, per the ST datasheet. The LQFP-48 package fits on small wearable PCAs with 5 V-tolerant GPIOs for charger integration.
Empfohlen
Smart Metering Endpoints
Smart metering applications benefit from the STM32L072CZT6's RTC with calendar, tamper detection, AES-128 hardware encryption, and 12-bit ADC for voltage/current sensing. The part's wide 1.65-3.6 V supply supports battery-backed meter designs, and the LQFP-48 footprint provides enough I/Os for meter interfaces. According to the datasheet, AES-128 hardware runs at low power without CPU overhead, securing AMI traffic.
Empfohlen
Medical Patch and Health Monitoring Devices
The STM32L072CZT6 suits medical patch devices thanks to its low-power modes, 12-bit ADC with hardware oversampling, and 192 KB Flash for DSP-style signal processing. According to the ST datasheet, the 12-bit ADC reaches 16-bit effective resolution with oversampling, supporting accurate bio-potential measurements. The LQFP-48 package is small enough for wearable form factors and has 5 V-tolerant GPIOs for sensor interfacing.
Empfohlen
Asset Tracking and Cold-Chain Loggers
Cold-chain and asset tracking applications benefit from the STM32L072CZT6's RTC calendar, low-power Stop mode, AES-128 for signed log integrity, and 192 KB Flash for local storage of time-stamped events. The 32 MHz Cortex-M0+ core is sufficient to drive temperature/humidity sampling and USB-based log extraction in field service. Per ST documentation, the part handles -40 C to +85 C industrial environments.
Empfohlen
Human-Machine Interface Panels
The STM32L072CZT6 supports HMI panel designs with its capacitive-touch sensing I/Os, 12-bit ADC for analog slider feedback, AES-128 for secure boot, and 192 KB Flash for graphics state machines. The LQFP-48 footprint provides sufficient I/O count for keypad scanning plus LCD segment driving via external drivers. The crystal-less USB interface supports field firmware updates without an external oscillator.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für STM32L072CZT6 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | STM32L073CZT6 | STM32L072CZT3 | STM32L072CZT6D | STM32L053CZT6 | STM32L083CZT6 |
|---|---|---|---|---|---|---|
| Package | LQFP-48 (7x7 mm) | LQFP-48 (7x7 mm) - same | LQFP-48 (7x7 mm) - same | LQFP-48 (7x7 mm) - same | LQFP-48 (7x7 mm) - same | LQFP-48 (7x7 mm) - same |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Flash Memory | 192 KB | 192 KB | 192 KB | 192 KB | 192 KB | 192 KB |
| SRAM | 20 KB | 20 KB | 20 KB | 20 KB | 20 KB | 20 KB |
| USB Peripheral | Yes (crystal-less USB 2.0 FS) | Yes | Yes | Yes | No | Yes |
| AES-128 Hardware | Yes | Yes | Yes | Yes | Yes | Yes |
| Wireless Connectivity | None | Sigfox | None | None | None | LoRa |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +125 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
| Supply Voltage | 1.65 V to 3.6 V | 1.65 V to 3.6 V | 1.65 V to 3.6 V | 1.65 V to 3.6 V | 1.65 V to 3.6 V | 1.65 V to 3.6 V |
Wichtigste Unterscheidungsmerkmale
- Crystal-less USB 2.0 full-speed peripheral (vs. STM32L053CZT6)
- Optional wireless connectivity without PCB rework (vs. STM32L073CZT6)
- 192 KB Flash headroom for USB stacks (vs. STM32L052C8T6)
Designhinweise
Estimated: at 32 MHz active core current with peripherals disabled the STM32L072CZT6 draws around 1 mA/MHz per ST datasheet figures. Add 100 nF + 10 uF ceramic decoupling near each VDD/VDDA pin and a ferrite bead between digital and analog supplies for clean ADC readings. Use the integrated voltage regulator to drive VDD from a 1.8 V to 3.3 V rail and avoid supplying core voltage externally.
At low duty cycles the STM32L072CZT6 spends nearly all its time in Stop or Standby, so self-heating is negligible. For continuous-active designs at 32 MHz, the LQFP-48 theta_JA around 65 C/W produces only a few degrees of rise even without a copper pour. Still place thermal vias under the exposed pad if your PCB stackup supports it.
Route the USB DP/DM pair (PA11/PA12) as a 90 ohm differential with length matching within 150 mils and keep them away from switching nodes. The crystal-less USB relies on internal trimming, so a clean 3.3 V rail with low ripple is essential. Per ST AN4879, place the USB common-mode choke near the connector side of the route.
Do not exceed 3.6 V on any pin including 5 V-tolerant GPIOs. Make sure BOOT0 is tied low for normal Flash boot and pulled high only for system memory bootloader access. Disable unused peripherals in PWR register settings before entering Stop mode to achieve sub-microamp current per the ST reference manual RM03510.
Compliance-Informationen
RoHS and REACH compliance per ST product page. Not AEC-Q100 qualified - this is a commercial/consumer part. For automotive applications use the equivalent -A or -Q suffix variant if available.
