TCA4311DRG4 - 400kHz Hot-Swap I2C Buffer | Texas Instruments
Teilenummer: TCA4311DRG4 ✓ AktivTCA4311DRG4 Übersicht
An I2C bus buffer is a bidirectional interface IC that separates a potentially noisy or capacitively loaded bus section from the rest of a two-wire bus. The TCA4311 belongs to the broader I2C interface IC hierarchy, where bus buffers, accelerators, repeaters, and hot-plug controllers support reliable communication between processors, sensors, memory devices, and expansion cards. Its 2-bit architecture provides two buffered channels in a compact surface-mount package.
The principal operating characteristics include a 2.7 V minimum supply, 5.5 V maximum supply, and support for 400 kHz I2C operation. The device is intended for hot-plug or hot-swap systems in which a peripheral may be connected to a live bus. Its bidirectional channels allow controller and peripheral traffic to pass through the buffer without changing the underlying open-drain I2C signaling method.
The TI TCA4311 product page identifies the device as a 2-bit bidirectional 2.7 V to 5.5 V hot-swappable 400 kHz I2C or SMBus buffer. The manufacturer datasheet explains that I2C limits total bus capacitance to 400 pF, while SMBus does not impose the same capacitance limit. A buffer can therefore divide a long or heavily loaded bus into shorter segments, reducing the capacitive burden seen by a controller while preserving communication across both segments.
Typical uses include industrial control modules, hot-pluggable sensor cards, server peripherals, communications equipment, and embedded systems that add or remove equipment while powered. It can also isolate a short, heavily loaded bus segment from a cleaner segment, improving rise-time behavior and reducing the probability that multiple peripheral pull-up networks combine into an excessive effective load.
When laying out a board, route the buffered bus sections as controlled transmission-line segments with continuous ground references, place the device close to the bus boundary, and keep both sides of the buffer free of unnecessary stubs. Confirm voltage compatibility, pull-up placement, logic levels, and bus capacitance before implementation because the buffer does not translate voltage levels or replace pull-up resistors.
This product page organizes the electrical characteristics, ordering information, drop-in alternatives, comparison parameters, and application guidance around the TCA4311DRG4. It is intended to accelerate component selection, PCB planning, and replacement analysis while keeping each engineering conclusion tied to the manufacturer documentation or an identified cross-reference result.
Drop-in-Alternativen für TCA4311DRG4 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit TCA4311DRG4 (gleiche Bauform und Footprint) – abweichend in Package, Product Type, Hot-Swap Support, Operating Temperature Range, Supported Bus.
TCA4311D
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →TCA4311ADR
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →TCA4311DRG4 Technische Daten
| Product Type | 2-bit bidirectional I2C/SMBus buffer accelerator |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Maximum I2C Bus Frequency | 400 kHz |
| Number of Buffered Channels | 2 bits |
| Bus Direction | Bidirectional |
| Supported Bus | I2C and SMBus |
| Hot-Swap Support | Yes |
| Betriebstemperaturbereich | -40 C to +85 C |
| Gehäuse | 8-pin SOIC, 3.90 mm width |
| Montageart | Surface mount |
| Eingangskapazität | 10 pF |
| I2C Maximum Bus Capacitance | 400 pF |
| SMBus Maximum Bus Capacitance | No specified restriction |
| Logic Interface | 2-wire bus |
| Output Interface | 2-wire bus |
| Signal Conditioning | Bus buffering and acceleration |
| Manufacturer Orderable Suffix | DRG4 |
| Standard Reel Quantity | 2500 units |
TCA4311DRG4 8-pin soic, 3.90 mm width Pinbelegungsleitfaden
Pinbelegung für TCA4311DRG4 (8-pin soic, 3.90 mm width-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für TCA4311DRG4.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
TCA4311DRG4 ist geeignet für 6 Anwendungs: Hot-Pluggable Sensor Cards, Industrial Control Module Bus Isolation, Server Peripheral Hot Plug, Communication Equipment Bus Extension, Portable Device External Connector, Test and Measurement Control Bus.
Hot-Pluggable Sensor Cards
The TCA4311DRG4 fits hot-pluggable sensor cards because it buffers two bidirectional I2C channels at rates up to 400 kHz while operating from 2.7 V to 5.5 V. Place the buffer between the removable card and the main controller bus so capacitance introduced by the card, cable, and pull-up network is isolated from the host-side bus. This separation can improve insertion behavior and reduce the load seen by the controller. The design must still verify logic-level compatibility, maintain short return paths, and follow the manufacturer application circuit for pull-ups and enable control.
Empfohlen
Industrial Control Module Bus Isolation
In an industrial control module, the TCA4311DRG4 can divide a long two-wire bus into a host segment and a peripheral segment. Its 400 kHz operating capability covers standard-speed I2C communication, while the 2.7 V to 5.5 V supply range supports embedded controller rails common in control equipment. Isolating a short peripheral branch limits the combined capacitive loading from multiple devices. For reliable operation, calculate the effective pull-up resistance on each buffered side, keep both bus grounds connected, and use the pin-description table in the Texas Instruments datasheet when routing the enable and bypass connections.
Empfohlen
Server Peripheral Hot Plug
The TCA4311DRG4 is useful at a server peripheral boundary where an I2C or SMBus device may be attached while the host remains powered. Its bidirectional 2-bit architecture lets the host and peripheral communicate across a segmented bus while limiting the disturbance caused by the peripheral-side capacitance. The 400 kHz maximum rate supports conventional I2C peripherals rather than high-speed modes above that frequency. System integrators should use short, impedance-controlled branches, verify that the peripheral uses a compatible voltage domain, and confirm the device status and thermal conditions of each enclosure.
Empfohlen
Communication Equipment Bus Extension
The TCA4311DRG4 can extend or segment an I2C bus in communications equipment where several low-speed management peripherals share a two-wire interface. Buffering the branch reduces the effective capacitance presented to the master and helps preserve the intended 400 kHz rise-time behavior. Because the TCA4311 is bidirectional, both controller-to-peripheral and peripheral-to-controller traffic pass through the same buffered path. Route each side as a controlled trace with a nearby ground reference, avoid long unterminated stubs, and place pull-up networks only where required by the manufacturer application guidance.
Empfohlen
Portable Device External Connector
A portable device can use the TCA4311DRG4 between an internal controller and an external connector carrying I2C signals, particularly when connection or disconnection while powered must be tolerated. The 2.7 V to 5.5 V operating range supports common portable-system supply rails, and the hot-swap architecture is intended for this type of bus interruption. Protection and signal-conditioning components may still be required for connector exposure, ESD, and cable-length concerns. The buffer should be positioned near the connector boundary, with its bus ground tied directly to the connector ground and its supply bypassed according to the manufacturer datasheet.
Empfohlen
Test and Measurement Control Bus
The TCA4311DRG4 is suitable for separating a measurement instrument's control bus from a larger set of sensors, adapters, or front-end modules. The buffered 400 kHz two-wire interface reduces the capacitive loading caused by remote cables and numerous connected pull-ups, improving the likelihood that rise and fall times remain within specification. A common arrangement places the TCA4311 near the instrument-side connector and another buffered segment near the remote equipment. Before layout release, verify the total cable capacitance, connector pin assignments, logic levels, and enable sequencing against the Texas Instruments TCA4311 documentation.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für TCA4311DRG4 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | TCA4311D | TCA4311A |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-SOIC | 8-SOIC | 8-SOIC |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Maximum Bus Frequency | 400 kHz | 400 kHz | 400 kHz |
| Buffered Channels | 2-bit bidirectional | 2-bit bidirectional | 2-bit bidirectional |
| Bus Compatibility | I2C and SMBus | I2C and SMBus | I2C and SMBus |
| Hot-Swap Capability | Yes | Yes | Yes |
Wichtigste Unterscheidungsmerkmale
- Directly identified completely replaceable alternative (vs. TCA4311D)
- Same-family hot-swap architecture (vs. TCA4311A)
- Production-friendly tape-and-reel ordering (vs. TCA4311D)
Designhinweise
Place the TCA4311DRG4 directly at the boundary between the host-side and peripheral-side bus segments. Keep each segment as short as practical, minimize stubs, and provide a continuous ground reference beneath the routed traces. The 400 kHz bus-rate target does not guarantee acceptable signal integrity in an arbitrary layout, so trace geometry, connector transitions, pull-up placement, and cable capacitance must be evaluated together.
Decouple the TCA4311DRG4 supply locally and connect the bypass capacitor close to the device's supply and ground pins. The supported 2.7 V to 5.5 V range covers 3.3 V and 5 V systems, but hot-plug transients can be reflected in the connector and cable environment. Verify the supply remains inside the manufacturer operating range during startup, insertion, removal, and normal bus activity.
Do not treat the TCA4311DRG4 as a level translator. It buffers bidirectional I2C or SMBus traffic but does not convert incompatible voltage domains. Also avoid adding pull-up networks indiscriminately on both sides of the buffer, because multiple pull-ups in parallel can reduce resistance too far and create excessive sink current. Follow the manufacturer application circuit and calculate each segment's effective pull-up resistance before layout release.
Compliance-Informationen
The general-purpose interface IC is not presented as an AEC-Q100-qualified automotive device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations must be confirmed from the manufacturer product page or current material-compliance documentation.