Texas Instruments

TCA4311DRG4 - 400kHz Hot-Swap I2C Buffer | Texas Instruments

MPN: TCA4311DRG4 ✓ פעיל
2.7 V to 5.5 V Vdss 8-pin SOIC, 3.90 mm width Package 400 kHz Speed
כמות הזמנה מינימלית: 1 |

TCA4311DRG4 סקירה

The Texas Instruments TCA4311DRG4 is a 2-bit bidirectional I2C and SMBus buffer accelerator with a 2.7 V to 5.5 V supply range, 400 kHz bus speed, hot-swap capability, and an 8-pin SOIC package. It supports two-wire bus buffering and allows systems to isolate bus capacitance while improving signal integrity during live insertion or removal.

An I2C bus buffer is a bidirectional interface IC that separates a potentially noisy or capacitively loaded bus section from the rest of a two-wire bus. The TCA4311 belongs to the broader I2C interface IC hierarchy, where bus buffers, accelerators, repeaters, and hot-plug controllers support reliable communication between processors, sensors, memory devices, and expansion cards. Its 2-bit architecture provides two buffered channels in a compact surface-mount package.

The principal operating characteristics include a 2.7 V minimum supply, 5.5 V maximum supply, and support for 400 kHz I2C operation. The device is intended for hot-plug or hot-swap systems in which a peripheral may be connected to a live bus. Its bidirectional channels allow controller and peripheral traffic to pass through the buffer without changing the underlying open-drain I2C signaling method.

The TI TCA4311 product page identifies the device as a 2-bit bidirectional 2.7 V to 5.5 V hot-swappable 400 kHz I2C or SMBus buffer. The manufacturer datasheet explains that I2C limits total bus capacitance to 400 pF, while SMBus does not impose the same capacitance limit. A buffer can therefore divide a long or heavily loaded bus into shorter segments, reducing the capacitive burden seen by a controller while preserving communication across both segments.

Typical uses include industrial control modules, hot-pluggable sensor cards, server peripherals, communications equipment, and embedded systems that add or remove equipment while powered. It can also isolate a short, heavily loaded bus segment from a cleaner segment, improving rise-time behavior and reducing the probability that multiple peripheral pull-up networks combine into an excessive effective load.

When laying out a board, route the buffered bus sections as controlled transmission-line segments with continuous ground references, place the device close to the bus boundary, and keep both sides of the buffer free of unnecessary stubs. Confirm voltage compatibility, pull-up placement, logic levels, and bus capacitance before implementation because the buffer does not translate voltage levels or replace pull-up resistors.

This product page organizes the electrical characteristics, ordering information, drop-in alternatives, comparison parameters, and application guidance around the TCA4311DRG4. It is intended to accelerate component selection, PCB planning, and replacement analysis while keeping each engineering conclusion tied to the manufacturer documentation or an identified cross-reference result.

חלופות תחליף ישיר עבור TCA4311DRG4 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

וריאנטים בסדרה זו

דגמים מאותה סדרה התואמים Drop-in עם TCA4311DRG4 (אותו גורם צורה וטביעת רגל) — שונים ב Package, Product Type, Hot-Swap Support, Operating Temperature Range, Supported Bus.

Texas Instruments
Package: 8-pin SOIC (D)
Product Type: Hot-swappable 2-wire bus buffer
Operating Temperature Range: -40 °C to +85 °C
השווה עם TCA4311DRG4 →
Texas Instruments
Package: 8-pin SOIC, 0.154 inch wide, 3.90 mm
Product Type: 2-bit bidirectional I2C/SMBus buffer
Hot-Swap Support: Yes, hot-swappable
השווה עם TCA4311DRG4 →

TCA4311D

✅ Drop-In
Texas Instruments
📦 8-SOIC
2-bit bidirectional I2C/SMBus buffer · 2.7 V to 5.5 V · 400 kHz · 2 bits · Bidirectional · I2C and SMBus · Yes, hot-swappable · EN pin; low enables shutdown mode

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

TCA4311ADR

✅ Drop-In
Texas Instruments
📦 8-SOIC
Hot-swappable 2-wire bus buffer · 2.7 V to 5.5 V · 400 kHz · 1 channel · 2 bits · Supported on SDA and SCL · Supported · 1 V on SDA and SCL

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

TCA4311DRG4 מפרטים

Product Type 2-bit bidirectional I2C/SMBus buffer accelerator
Supply Voltage Range 2.7 V to 5.5 V
Maximum I2C Bus Frequency 400 kHz
Number of Buffered Channels 2 bits
Bus Direction Bidirectional
Supported Bus I2C and SMBus
Hot-Swap Support Yes
טווח טמפרטורת פעולה -40 C to +85 C
מארז 8-pin SOIC, 3.90 mm width
סוג הרכבה Surface mount
קיבול כניסה 10 pF
I2C Maximum Bus Capacitance 400 pF
SMBus Maximum Bus Capacitance No specified restriction
Logic Interface 2-wire bus
Output Interface 2-wire bus
Signal Conditioning Bus buffering and acceleration
Manufacturer Orderable Suffix DRG4
Standard Reel Quantity 2500 units

מדריך תצורת פינים של TCA4311DRG4 8-pin soic, 3.90 mm width

תצורת פינים עבור TCA4311DRG4 (מארזת 8-pin soic, 3.90 mm width). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.

תרשים פינים של מארזת 8-pin soic, 3.90 mm width עבור TCA4311DRG4

אין נתוני פריסת פינים מפורטים עבור TCA4311DRG4.

עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.

יישומים טיפוסיים

TCA4311DRG4 מתאים עבור 6 יישוםs: Hot-Pluggable Sensor Cards, Industrial Control Module Bus Isolation, Server Peripheral Hot Plug, Communication Equipment Bus Extension, Portable Device External Connector, Test and Measurement Control Bus.

🧩

Hot-Pluggable Sensor Cards

The TCA4311DRG4 fits hot-pluggable sensor cards because it buffers two bidirectional I2C channels at rates up to 400 kHz while operating from 2.7 V to 5.5 V. Place the buffer between the removable card and the main controller bus so capacitance introduced by the card, cable, and pull-up network is isolated from the host-side bus. This separation can improve insertion behavior and reduce the load seen by the controller. The design must still verify logic-level compatibility, maintain short return paths, and follow the manufacturer application circuit for pull-ups and enable control.

🏭

Industrial Control Module Bus Isolation

In an industrial control module, the TCA4311DRG4 can divide a long two-wire bus into a host segment and a peripheral segment. Its 400 kHz operating capability covers standard-speed I2C communication, while the 2.7 V to 5.5 V supply range supports embedded controller rails common in control equipment. Isolating a short peripheral branch limits the combined capacitive loading from multiple devices. For reliable operation, calculate the effective pull-up resistance on each buffered side, keep both bus grounds connected, and use the pin-description table in the Texas Instruments datasheet when routing the enable and bypass connections.

🖥️

Server Peripheral Hot Plug

The TCA4311DRG4 is useful at a server peripheral boundary where an I2C or SMBus device may be attached while the host remains powered. Its bidirectional 2-bit architecture lets the host and peripheral communicate across a segmented bus while limiting the disturbance caused by the peripheral-side capacitance. The 400 kHz maximum rate supports conventional I2C peripherals rather than high-speed modes above that frequency. System integrators should use short, impedance-controlled branches, verify that the peripheral uses a compatible voltage domain, and confirm the device status and thermal conditions of each enclosure.

🌐

Communication Equipment Bus Extension

The TCA4311DRG4 can extend or segment an I2C bus in communications equipment where several low-speed management peripherals share a two-wire interface. Buffering the branch reduces the effective capacitance presented to the master and helps preserve the intended 400 kHz rise-time behavior. Because the TCA4311 is bidirectional, both controller-to-peripheral and peripheral-to-controller traffic pass through the same buffered path. Route each side as a controlled trace with a nearby ground reference, avoid long unterminated stubs, and place pull-up networks only where required by the manufacturer application guidance.

📱

Portable Device External Connector

A portable device can use the TCA4311DRG4 between an internal controller and an external connector carrying I2C signals, particularly when connection or disconnection while powered must be tolerated. The 2.7 V to 5.5 V operating range supports common portable-system supply rails, and the hot-swap architecture is intended for this type of bus interruption. Protection and signal-conditioning components may still be required for connector exposure, ESD, and cable-length concerns. The buffer should be positioned near the connector boundary, with its bus ground tied directly to the connector ground and its supply bypassed according to the manufacturer datasheet.

🔧

Test and Measurement Control Bus

The TCA4311DRG4 is suitable for separating a measurement instrument's control bus from a larger set of sensors, adapters, or front-end modules. The buffered 400 kHz two-wire interface reduces the capacitive loading caused by remote cables and numerous connected pull-ups, improving the likelihood that rise and fall times remain within specification. A common arrangement places the TCA4311 near the instrument-side connector and another buffered segment near the remote equipment. Before layout release, verify the total cable capacitance, connector pin assignments, logic levels, and enable sequencing against the Texas Instruments TCA4311 documentation.

סיכום מוצרים מומלצים

TCA4311D Texas Instruments בשימוש ב-: Hot-Pluggable Sensor Cards, Industrial Control Module Bus Isolation, Server Peripheral Hot Plug, Communication Equipment Bus Extension, Portable Device External Connector, Test and Measurement Control Bus TCA4311A Same-family buffered hot-plug interface candidate בשימוש ב-: Hot-Pluggable Sensor Cards, Industrial Control Module Bus Isolation, Server Peripheral Hot Plug, Communication Equipment Bus Extension, Portable Device External Connector, Test and Measurement Control Bus
What is the TCA4311DRG4?
The TCA4311DRG4 is a 2-bit bidirectional I2C and SMBus buffer accelerator that supports 400 kHz bus operation from a 2.7 V to 5.5 V supply. According to the Texas Instruments TCA4311 product page, the device is designed for hot-swappable two-wire buses and is housed in an 8-pin SOIC package.
What is the operating voltage range of TCA4311DRG4?
The TCA4311DRG4 operates from 2.7 V to 5.5 V. The Texas Instruments product page lists this supply range for the TCA4311 family, making the device suitable for common 3.3 V and 5 V system rails. The manufacturer datasheet should be used to confirm operating limits for the selected temperature range.
What is the maximum bus speed supported by TCA4311DRG4?
The TCA4311DRG4 supports I2C operation up to 400 kHz. According to the Texas Instruments TCA4311 product page, it is a 400 kHz hot-swappable buffer for I2C or SMBus communication. Actual bus speed still depends on pull-up resistance, bus capacitance, clock rise time, and the electrical characteristics of connected peripherals.
Where can I download the TCA4311DRG4 datasheet PDF?
The official TCA4311DRG4 datasheet PDF is available from the Texas Instruments document link at https://www.ti.com/lit/ds/symlink/tca4311.pdf. The document contains the electrical characteristics, application circuit, bus-capacitance information, and device pin descriptions needed to evaluate the TCA4311 in an I2C or SMBus design.
Where can I find the TCA4311DRG4 pinout?
The TCA4311DRG4 pinout is defined by the pin-description table in the official Texas Instruments TCA4311 datasheet. The device uses an 8-pin SOIC package, but pin names and functions should be assigned directly from the manufacturer pin table rather than inferred from another bus-buffer family. Use that table when routing the enable, ground, and bidirectional bus connections.
How does TCA4311DRG4 support I2C hot swap?
The TCA4311DRG4 is designed to permit peripheral insertion into a live two-wire bus by buffering the segmented bus and limiting the disturbance visible to the rest of the system. According to the manufacturer datasheet, the I2C specification limits total bus capacitance to 400 pF, so segmentation and isolation can make a practical bus architecture possible.
TCA4311DRG4 vs TCA4311D - which is the better replacement?
The TCA4311D is the closest identified same-family alternative because the cross-reference information describes its terminals and 8-pin SOIC package as completely replaceable for TCA4311DRG4. The DRG4 ordering code adds tape-and-reel packaging, so the electrical distinction is primarily the orderable package suffix rather than the bus-buffer function.
Can TCA4311A replace TCA4311DRG4 pin to pin?
The TCA4311A is a same-family candidate for review because Texas Instruments discusses it in connection with I2C buffers that support 3.3 V signaling on a 5 V bus and hot connections. The manufacturer discussion confirms functional relevance, but engineers should verify the exact 8-pin SOIC footprint and pin assignments in the TCA4311A datasheet before treating it as a drop-in replacement.
What is the best drop-in replacement for TCA4311DRG4?
The TCA4311D is the best directly identified drop-in candidate because the manufacturer-related cross-reference describes matching terminals, package, and functional characteristics. The TCA4311A is another same-family option for pin-level review. Both should be checked against the current datasheet and production requirements rather than selected solely from the family name.
What can replace TCA4311DRG4?
TCA4311D can replace TCA4311DRG4 according to the identified cross-reference result, which describes the two 8-pin SOIC devices as completely replaceable. TCA4311A is a second same-family candidate, while LTC4301 was discussed as having a similar pinout but is not included here because the cited discussion does not establish the same package and footprint.
When should I choose TCA4311DRG4 over another I2C buffer?
Choose the TCA4311DRG4 when the design needs a 2-bit bidirectional 2.7 V to 5.5 V I2C or SMBus buffer with 400 kHz operation and hot-swap capability. It is particularly appropriate when a live bus must be segmented to isolate capacitance or when a peripheral may be inserted while the system remains powered.
Is TCA4311DRG4 suitable for hot-pluggable sensor modules?
The TCA4311DRG4 is suitable for hot-pluggable sensor modules because it is explicitly identified as a hot-swappable I2C or SMBus buffer. Its two buffered channels can separate a peripheral segment from the main bus, but the implementation still requires correct pull-ups, voltage-level compatibility, grounded return paths, and a design that satisfies the applicable bus-capacitance limits.
How much bus capacitance can TCA4311DRG4 handle?
The I2C specification cited in the Texas Instruments datasheet allows 400 pF maximum bus capacitance. That figure describes the permitted bus load for compliant I2C operation rather than a dedicated capacitor rating printed for the TCA4311DRG4 itself. Actual channel loading and system margin must be evaluated from the manufacturer electrical-characteristics tables.
Is TCA4311DRG4 suitable for 3.3 V and 5 V systems?
The TCA4311DRG4 supports a 2.7 V to 5.5 V operating supply, which covers both 3.3 V and 5 V rails. The Texas Instruments product page identifies this range for the TCA4311 family. The buffer does not automatically translate logic levels, so both connected devices must still use compatible voltage domains.
Where can I buy TCA4311DRG4 and check its lead time?
Use the Request a Quote form on this page to request TCA4311DRG4 availability, current lead time, and order quantities. The Request a Quote workflow is the appropriate channel for an exact-MPN sourcing request because component inventory and delivery schedules change. Quote requests can also confirm whether the required DRG4 tape-and-reel format is available.

נתוני עזר הנדסיים עבור TCA4311DRG4 — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose TCA4311DRG4 for a 400 kHz, 2-bit bidirectional I2C or SMBus design that operates from 2.7 V to 5.5 V and benefits from hot-swap bus isolation. Choose TCA4311D when it is the directly identified completely replaceable option and its available orderable format suits the assembly process. Consider TCA4311A when reviewing another member of the same hot-swap buffer family, but verify its detailed enable thresholds, temperature limits, and pin assignments before committing it to an existing layout. LTC4301 should not be assumed to be a direct substitute because a similar pinout alone does not establish the same 8-SOIC footprint. For any option, verify voltage compatibility, pull-up values, bus capacitance, hot-plug behavior, and current sourcing needs.

השוואה עם חלופות

פרמטר מוצר זה TCA4311D TCA4311A
Brand Texas Instruments Texas Instruments Texas Instruments
Package 8-SOIC 8-SOIC 8-SOIC
Supply Voltage Range 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V
Maximum Bus Frequency 400 kHz 400 kHz 400 kHz
Buffered Channels 2-bit bidirectional 2-bit bidirectional 2-bit bidirectional
Bus Compatibility I2C and SMBus I2C and SMBus I2C and SMBus
Hot-Swap Capability Yes Yes Yes

מבדילים עיקריים

  • Directly identified completely replaceable alternative (לעומתTCA4311D)
  • Same-family hot-swap architecture (לעומתTCA4311A)
  • Production-friendly tape-and-reel ordering (לעומתTCA4311D)

הערות תכנון

Place the TCA4311DRG4 directly at the boundary between the host-side and peripheral-side bus segments. Keep each segment as short as practical, minimize stubs, and provide a continuous ground reference beneath the routed traces. The 400 kHz bus-rate target does not guarantee acceptable signal integrity in an arbitrary layout, so trace geometry, connector transitions, pull-up placement, and cable capacitance must be evaluated together.

Decouple the TCA4311DRG4 supply locally and connect the bypass capacitor close to the device's supply and ground pins. The supported 2.7 V to 5.5 V range covers 3.3 V and 5 V systems, but hot-plug transients can be reflected in the connector and cable environment. Verify the supply remains inside the manufacturer operating range during startup, insertion, removal, and normal bus activity.

Do not treat the TCA4311DRG4 as a level translator. It buffers bidirectional I2C or SMBus traffic but does not convert incompatible voltage domains. Also avoid adding pull-up networks indiscriminately on both sides of the buffer, because multiple pull-ups in parallel can reduce resistance too far and create excessive sink current. Follow the manufacturer application circuit and calculate each segment's effective pull-up resistance before layout release.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

The general-purpose interface IC is not presented as an AEC-Q100-qualified automotive device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations must be confirmed from the manufacturer product page or current material-compliance documentation.

חיפושים קשורים

TCA4311DRG4 TCA4311DRG4 datasheet TCA4311DRG4 datasheet pdf TCA4311DRG4 pinout TCA4311DRG4 equivalent TCA4311DRG4 replacement TCA4311DRG4 cross reference TCA4311DRG4 vs TCA4311D Texas Instruments TCA4311DRG4 TCA4311DRG4 400kHz TCA4311DRG4 2.7V 5.5V TCA4311DRG4 SOIC-8 TCA4311DRG4 I2C hot swap TCA4311DRG4 price TCA4311DRG4 stock

רכיבים ומונחים קשורים

Texas Instruments TCA4311DRG4 TCA4311D TCA4311A I2C SMBus two-wire bus bidirectional bus buffer bus accelerator hot-swap buffer hot-plug interface bus isolation bus capacitance 400 kHz I2C 2.7 V to 5.5 V supply open-drain signaling 8-SOIC package SOIC family surface-mount package interface IC semiconductor pull-up resistor rise-time control
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר