TLE42662GHTMA2 - 5V 150mA LDO Regulator w/ INH | Infineon
Teilenummer: TLE42662GHTMA2 ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $2.55 | $2,55 |
| 10 | $2.29 | $22,90 |
| 100 | $1.84 | $184,00 |
| 500 | $1.47 | $735,00 |
| 1.000 | $1.18 | $1.180,00 |
TLE42662GHTMA2 Übersicht
A Low-Dropout (LDO) regulator is a type of linear voltage regulator that maintains a stable output voltage even when the input-to-output voltage difference is small. Within the broader semiconductor taxonomy, an LDO belongs to the family of linear regulators, which in turn are a subclass of voltage regulators, falling under the power management IC (PMIC) category. The TLE42662GHTMA2 is part of Infineon's OPTIREG™ linear family and is functionally compatible with the legacy TLE4266 device, but with substantially reduced quiescent current for always-on automotive applications.
Key features include a fixed 5 V output with tight regulation accuracy, current limit protection, thermal shutdown, overtemperature protection, and reverse-polarity protection. The INH pin enables the regulator to be put into a low-quiescent standby state, which is essential for automotive modules that must remain connected to the battery without draining it during parking. The SOT-223-4 package provides sufficient copper area on its tab to dissipate heat at moderate load currents without external heatsinking.
The device uses a monolithic bipolar architecture with an integrated pass element and bandgap reference. The architecture is optimized for very low quiescent current draw while still providing the transient response and PSRR required for microcontroller and sensor supply rails. Built-in protective features guard against load-dump transients common in automotive electrical systems.
Typical applications include automotive microcontroller power supplies, body and chassis ECUs, sensor and actuator power rails, and always-on standby supplies for CAN/LIN transceivers. It is qualified for use in harsh automotive environments. When designing with this regulator, ensure that the input voltage remains within the safe operating range under load-dump conditions and that the SOT-223-4 tab is soldered to a sufficiently large copper pour to manage thermals at full 150 mA load.
This page synthesizes distributor pricing from DigiKey, Mouser, and Octopart, plus drop-in SOT-223-4 alternatives and practical PCB layout notes not found in the manufacturer datasheet, giving procurement and design engineers a single source of truth for sourcing and replacement decisions.
Drop-in-Alternativen für TLE42662GHTMA2 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit TLE42662GHTMA2 (gleiche Bauform und Footprint) – abweichend in Package, Protection Features, Input Voltage Range, Output Voltage Accuracy, Maximum Output Current.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
TLE4266-2G
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
TLE4266G
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
TLE42662GHTSA1
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
TLS715B0EJV50XUMA1
✅ Drop-In✓ Auf Lager
$0.55 / Stück
Datenblatt ansehen →IFX1051LE
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
TLE42662GHTMA2 Grenzwerte & elektrische Eigenschaften
| Manufacturer | Infineon Technologies |
| Product Type | LDO Linear Voltage Regulator (Fixed Output) |
| Ausgangsspannung | 5 V (fixed) |
| Ausgangsstrom (max.) | 150 mA |
| Quiescent Current (ON) | 40 µA typical |
| Quiescent Current (OFF / INH low) | < 1 µA |
| Inhibit Pin (INH) | Yes (active-high; low = standby) |
| Protection Features | Current limit, overtemperature shutdown, reverse polarity |
| Gehäuse | PG-SOT223-4 (SOT-223-4 / TO-261-4) |
| Montageart | Surface Mount |
| Automotive Qualified | Yes (Infineon OPTIREG linear family for automotive) |
| RoHS-Status | Compliant |
| Lead-Free | Yes |
TLE42662GHTMA2 Pin-Konfiguration
| Pin 1 | IN — Input supply voltage (battery / pre-regulated rail) |
| Pin 2 | GND — Ground reference; also connected to metal tab for thermal dissipation |
| Pin 3 | INH — Inhibit input — pull high to enable, low for standby (< 1 µA Iq) |
| Pin 4 | OUT — Regulated 5 V output (up to 150 mA) |
Typische Anwendungen
TLE42662GHTMA2 ist geeignet für 6 Anwendungs: Automotive Body & Chassis ECU Power Supply, Always-On CAN/LIN Transceiver Standby Rail, Automotive Sensor Power Rail (5 V), Industrial 24 V PLC Logic Supply, Battery-Powered IoT Edge Node, LED Indicator & Display Driver Supply.
Automotive Body & Chassis ECU Power Supply
Provides a clean 5 V supply to body control modules (BCMs), door-zone ECUs, and lighting controllers operating from a 12 V automotive battery rail. The TLE42662GHTMA2's 150 mA output capability covers typical microcontroller plus sensor and relay-driver logic loads, while the INH pin supports key-off sleep modes with quiescent current dropping below 1 µA. Reverse-polarity and load-dump robustness from the OPTIREG linear architecture protects the ECU during jump-start and cranking transients, and the SOT-223-4 tab solders directly to a copper pour for thermal relief at full 150 mA load.
Empfohlen
Always-On CAN/LIN Transceiver Standby Rail
Supplies the standby logic of CAN and LIN transceivers that must remain connected to the automotive bus during vehicle parking to handle wake-up frames. The TLE42662GHTMA2's < 1 µA OFF-mode quiescent current preserves battery life over weeks of inactivity, while the 5 V fixed output matches the VIO rail requirements of modern automotive transceivers. The INH pin can be tied to the wake-up output of the transceiver so the rest of the ECU only powers up when a valid wake frame is received, dramatically reducing quiescent drain.
Empfohlen
Automotive Sensor Power Rail (5 V)
Powers 5 V automotive sensors such as pressure, temperature, and Hall-effect devices that feed the ECU's analog front end. The TLE42662GHTMA2's low output noise and tight line/load regulation keep sensor readings stable across cranking transients, while internal current limiting protects against sensor short-to-battery faults. The SOT-223-4 footprint mounts on the same sensor PCB or ECU sub-board as the sensor itself, simplifying harness design and reducing wire count compared to a centralized regulator.
Empfohlen
Industrial 24 V PLC Logic Supply
Steps a 24 V industrial bus down to a clean 5 V rail for PLC logic, isolated I/O modules, and HMI controllers. The TLE42662GHTMA2 handles industrial surge and brownout events thanks to its reverse-polarity and thermal protection, and the INH pin enables software-controlled standby of unused I/O banks. Although the input voltage must stay within the regulator's safe range (verify against the datasheet absolute maximums), the part's automotive-grade robustness makes it a reliable choice for factory-floor deployments where electrical noise is heavy.
Empfohlen
Battery-Powered IoT Edge Node
Provides regulated 5 V to IoT edge nodes, smart-home bridges, and remote telemetry units powered by a 12 V or multi-cell battery pack. The TLE42662GHTMA2's < 1 µA standby via INH lets the node sleep for months between transmissions, while its 150 mA output supports short bursts of wireless transmission and sensor acquisition. Combined with a low-Iq microcontroller, the system can operate from a small battery for extended service intervals without maintenance.
Empfohlen
LED Indicator & Display Driver Supply
Supplies constant 5 V to status LEDs, segment displays, and small graphic OLED panels in automotive instrument clusters, infotainment heads, and after-market dashboards. The TLE42662GHTMA2's low output noise prevents visible flicker in PWM-dimmed LED strings, and its thermal shutdown protects the regulator if a display fault shorts the supply rail. The INH pin can be tied to the cluster's ignition-sense line so the display powers down cleanly when the vehicle is off.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für TLE42662GHTMA2 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | TLE4266-2G | TLE4266G | TLE42662GHTSA1 | TLS715B0EJV50XUMA1 | IFX1051LE |
|---|---|---|---|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| Package | PG-SOT223-4 | PG-SOT223-4 - same | PG-SOT223-4 - same | PG-SOT223-4 - same | PG-SOT223-4 - same | PG-SOT223-4 - same |
| Output Voltage | 5 V (fixed) | 5 V (fixed) | 5 V (fixed) | 5 V (fixed) | 5 V (fixed) | 5 V (fixed) |
| Output Current (max) | 150 mA | 150 mA | 150 mA | 150 mA | 150 mA+ | 150 mA |
| INH / Enable Pin | Yes (active-high inhibit) | Yes | Yes | Yes | EN pin (different polarity - verify) | Yes |
| Reverse-Polarity Protection | Yes | Yes | Yes | Yes | Yes | Yes |
Wichtigste Unterscheidungsmerkmale
- Sub-1 µA standby quiescent current with INH control (vs. TLE4266G (legacy))
- Pin-compatible upgrade path within OPTIREG family (vs. TLE4266-2G (bare die))
- Compact 5 V/150 mA in SOT-223-4 with INH (vs. TLE42702DATMA1 (1 A in DPAK))
Designhinweise
At VIN = 12 V, VOUT = 5 V, and 150 mA load, the TLE42662GHTMA2 dissipates roughly 1.05 W. Solder the SOT-223-4 metal tab to at least 100 mm² of 1 oz copper pour to keep junction temperature within safe limits. For continuous loads above 100 mA in an enclosed automotive housing, add thermal vias to an inner plane and consider derating above 85 °C ambient.
Place the input capacitor (≥ 100 nF, low-ESR ceramic) as close as possible to the IN pin and the output capacitor (≥ 1 µF, low-ESR ceramic or tantalum) close to the OUT pin. Minimize the loop area between IN/GND and OUT/GND to reduce high-frequency noise and improve transient response. Keep the INH trace away from switching nodes to avoid spurious enable pulses.
Do not leave the INH pin floating — if unused, tie it directly to IN through a 100 kΩ resistor to guarantee regulator enable. Do not exceed the absolute maximum input voltage (refer to the Infineon datasheet for the exact value). Avoid reverse-polarity events by ensuring the input protection network handles load-dump transients typical of 12 V automotive systems.
Compliance-Informationen
AEC-Q100 qualification per Infineon OPTIREG automotive linear family. RoHS and REACH compliance per Infineon product page. Halogen-free status not explicitly stated in provided data — marked unknown.
