TLV2770IP - 5.1MHz Rail-to-Rail Op Amp | Texas Instruments
Teilenummer: TLV2770IP ✓ AktivTLV2770IP Übersicht
An operational amplifier, commonly called an op amp, is a voltage-gain element used to amplify small signals, buffer high-impedance sources, compare voltages, or drive analog stages. The TLV2770 belongs to the single-amplifier family within the broader hierarchy of analog integrated circuits, analog signal-chain ICs, and power-management-aware semiconductor designs. Its rail-to-rail output stage is intended to produce useful output voltage closer to the supply rails than a conventional output stage.
The headline characteristics are a 5.1 MHz gain-bandwidth product, a 10.5 V/µs slew rate, and operation from 2.7 V to 5.5 V. These specifications suit applications such as sensor-signal conditioning, active filtering, audio preamplification, and general-purpose analog buffers. The shutdown function provides a way to reduce power use when the amplifier is not needed, which can be useful in portable and intermittently powered systems.
Technically, gain-bandwidth product describes the relationship between closed-loop gain and bandwidth, while slew rate limits how quickly the output can move through large voltage changes. The TLV2770's combination favors relatively fast small-signal operation and reasonably clean large-signal transitions. Designers should still verify noise, input-offset voltage, output-current capability, stability, and load behavior against their exact operating conditions before releasing a production design.
Typical applications include low-voltage sensor interfaces, precision current-feedback signal paths, active low-pass filters, audio input stages, battery-powered instrumentation, and general analog signal conditioning. The 8-PDIP through-hole package is useful for prototypes, educational platforms, repair assemblies, and designs where a socketed DIP footprint is preferred over a compact surface-mount package.
A key design consideration is bypassing the supply pins with short, low-inductance connections and placing stable input and feedback networks close to the amplifier. Confirm the shutdown-pin logic and timing in the manufacturer datasheet before using the device for power sequencing. Because this is an analog IC rather than a power semiconductor, a safe operating area chart is not applicable.
This product record combines manufacturer and distributor information with application guidance, comparison parameters, and practical design notes. It highlights the TLV2770IP's 2.7 V minimum supply, 5.5 V maximum supply, 5.1 MHz bandwidth, 10.5 V/µs slew rate, rail-to-rail output, shutdown capability, and 8-PDIP packaging in one engineering-focused reference.
Drop-in-Alternativen für TLV2770IP – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
TLV2770CP
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
TLV2770IP Grenzwerte & elektrische Eigenschaften
| Amplifier Type | Single operational amplifier |
| Number of Circuits | 1 circuit |
| Supply Voltage Minimum | 2.7 V |
| Supply Voltage Maximum | 5.5 V |
| Gain-Bandwidth Product | 5.1 MHz |
| Slew Rate | 10.5 V/µs |
| Output Topology | Rail-to-rail output |
| Shutdown Function | Supported |
| Operating Temperature Minimum | -40 °C |
| Operating Temperature Maximum | 125 °C |
| Package Type | 8-PDIP |
| Anzahl der Pins | 8 pins |
| Montageart | Through-hole |
TLV2770IP 8-pdip Pinbelegungsleitfaden
Pinbelegung für TLV2770IP (8-pdip-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.
Keine detaillierten Pinbelegungsdaten verfügbar für TLV2770IP.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
TLV2770IP ist geeignet für 6 Anwendungs: Low-Voltage Sensor Signal Conditioning, Active Low-Pass Filtering, Audio Preamplification, Battery-Powered Instrumentation, Industrial Control Signal Interface, Portable Data-Acquisition Module.
Low-Voltage Sensor Signal Conditioning
The TLV2770IP fits sensor front ends that require more bandwidth than a slow general-purpose amplifier but do not need a high-voltage supply. Its 5.1 MHz gain-bandwidth product and 10.5 V/µs slew rate provide useful dynamic range for pressure, temperature, and position-sensor signals operating from 2.7 V to 5.5 V. Place the amplifier in a non-inverting or differential conditioning stage, then keep sensor return paths and feedback resistors close to the device to limit parasitic pickup. Verify the input common-mode range against the sensor output and include filtering where sensor bandwidth is lower than the amplifier bandwidth.
Empfohlen
Active Low-Pass Filtering
The TLV2770IP can implement an active low-pass filter in a 3.3 V or 5 V analog subsystem because its 5.1 MHz gain-bandwidth product leaves bandwidth above many practical filter cutoffs. The 10.5 V/µs slew rate also helps the output follow filter transitions without excessive delay for moderate signals. Build the filter around the device's prescribed noise-gain network, and place the operational amplifier, feedback components, and signal nodes close together to reduce board-level interference. Confirm noise, offset, common-mode behavior, and capacitor tolerances in the datasheet when the filter has high stopband attenuation requirements.
Empfohlen
Audio Preamplification
The TLV2770IP is applicable to low-voltage audio preamplifier stages where the 10.5 V/µs slew rate is preferable to the response of a low-bandwidth general-purpose op amp. Rail-to-rail output can increase the usable signal range in 2.7 V to 5.5 V single-supply systems, while the 5.1 MHz gain-bandwidth product supports audio-band closed-loop gains with practical bandwidth margin. The shutdown feature may reduce power consumption when the signal path is inactive. Headroom, output-current capability, noise, and distortion must be checked against the headphone, line, or speaker load before finalizing the stage.
Empfohlen
Battery-Powered Instrumentation
The TLV2770IP suits low-power instrumentation built around a 3.3 V or 5 V rail because it starts at 2.7 V and includes a shutdown function. The 5.1 MHz gain-bandwidth product and 10.5 V/µs slew rate allow the device to serve as a signal buffer, gain stage, or active filter rather than merely a precision DC amplifier. Shutdown can reduce activity when a measurement cycle is complete, but timing and logic levels must be controlled carefully. Use short supply paths, local decoupling, and a quiet ground reference to prevent the faster amplifier from amplifying board noise or switching transients.
Empfohlen
Industrial Control Signal Interface
The TLV2770IP can condition low-level control signals in industrial equipment operating from a 2.7 V to 5.5 V rail. Its rail-to-rail output and 10.5 V/µs slew rate are useful for driving downstream analog or mixed-signal stages through moderate impedances, while the 5.1 MHz bandwidth supports faster control-loop or interface signals. Maintain a common ground reference between the source and amplifier, protect external wiring from transients, and avoid driving long capacitive cables directly from the output without isolation or buffering. Review output-current and capacitive-load limits before using the device near connector or relay-driver circuits.
Empfohlen
Portable Data-Acquisition Module
The TLV2770IP is a practical fit for portable data-acquisition modules that need signal conditioning from a low-voltage battery-regulated supply. Its 5.1 MHz gain-bandwidth product supports moderately fast analog channels, and the shutdown capability can help a multichannel design isolate inactive circuitry. Use the amplifier for gain, current-to-voltage conversion, or active filtering, depending on the source impedance and required bandwidth. High-impedance sensors may require attention to bias current and offset, while ADC-driving paths require checking capacitive loading and settling behavior. Keep the analog return path compact and isolate fast digital switching from the signal input.
Empfohlen
Technische Referenzdaten für TLV2770IP – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | TLV2770CP |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-PDIP | 8-PDIP - same package |
| Amplifier Type | Single rail-to-rail output operational amplifier | Single rail-to-rail output operational amplifier |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Gain-Bandwidth Product | 5.1 MHz | 5.1 MHz |
| Slew Rate | 10.5 V/µs | 10.5 V/µs |
| Shutdown Function | Supported | Supported |
| Operating Temperature Range | -40 °C to 125 °C | -40 °C to 125 °C |
| Pin Compatibility | 8-PDIP pin configuration | Consistent terminals; no circuit modification required |
Wichtigste Unterscheidungsmerkmale
- High-speed operation in an 8-PDIP analog package (vs. TLV2770CP)
- Rail-to-rail output for low-voltage analog systems (vs. TLV2770CP)
- Integrated shutdown for power management (vs. TLV2770CP)
Designhinweise
Operate the TLV2770IP only within its 2.7 V to 5.5 V specified supply range. Place the supply-decoupling capacitor close to the power pins and use the manufacturer-recommended network and capacitor type. Treat the shutdown control as a sequencing input: its permitted voltage and transition behavior should be verified before tying it to a microcontroller or power-management signal. Keeping the power loop compact helps the 5.1 MHz bandwidth stage remain stable in practical layouts.
Route the op-amp input, feedback, and output paths to minimize loop area and susceptibility to switching noise. Place high-value feedback resistors close to the relevant device pins where practical, and keep the analog signal path away from clock and power-converter routing. Because the 10.5 V/µs slew rate can respond quickly to unwanted coupling, use a quiet return path and controlled board stackup. Validate the finished layout with stability and signal-integrity measurements.
Do not select the amplifier from bandwidth and slew rate alone. Check input common-mode range, offset voltage, bias current, noise, output-current capability, capacitive-load behavior, and shutdown logic for the intended circuit. A 5.1 MHz gain-bandwidth product does not guarantee 5.1 MHz operation at every closed-loop gain, and rail-to-rail output does not mean the input common-mode range reaches both rails. Use the device-specific manufacturer datasheet as the final electrical-selection reference.
Compliance-Informationen
The manufacturer and distributor records identify the TLV2770IP and its operating characteristics but do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. These fields therefore remain unknown.