TLV2770IP - 5.1MHz Rail-to-Rail Op Amp | Texas Instruments
MPN: TLV2770IP ✓ 啟用中TLV2770IP 概覽
An operational amplifier, commonly called an op amp, is a voltage-gain element used to amplify small signals, buffer high-impedance sources, compare voltages, or drive analog stages. The TLV2770 belongs to the single-amplifier family within the broader hierarchy of analog integrated circuits, analog signal-chain ICs, and power-management-aware semiconductor designs. Its rail-to-rail output stage is intended to produce useful output voltage closer to the supply rails than a conventional output stage.
The headline characteristics are a 5.1 MHz gain-bandwidth product, a 10.5 V/µs slew rate, and operation from 2.7 V to 5.5 V. These specifications suit applications such as sensor-signal conditioning, active filtering, audio preamplification, and general-purpose analog buffers. The shutdown function provides a way to reduce power use when the amplifier is not needed, which can be useful in portable and intermittently powered systems.
Technically, gain-bandwidth product describes the relationship between closed-loop gain and bandwidth, while slew rate limits how quickly the output can move through large voltage changes. The TLV2770's combination favors relatively fast small-signal operation and reasonably clean large-signal transitions. Designers should still verify noise, input-offset voltage, output-current capability, stability, and load behavior against their exact operating conditions before releasing a production design.
Typical applications include low-voltage sensor interfaces, precision current-feedback signal paths, active low-pass filters, audio input stages, battery-powered instrumentation, and general analog signal conditioning. The 8-PDIP through-hole package is useful for prototypes, educational platforms, repair assemblies, and designs where a socketed DIP footprint is preferred over a compact surface-mount package.
A key design consideration is bypassing the supply pins with short, low-inductance connections and placing stable input and feedback networks close to the amplifier. Confirm the shutdown-pin logic and timing in the manufacturer datasheet before using the device for power sequencing. Because this is an analog IC rather than a power semiconductor, a safe operating area chart is not applicable.
This product record combines manufacturer and distributor information with application guidance, comparison parameters, and practical design notes. It highlights the TLV2770IP's 2.7 V minimum supply, 5.5 V maximum supply, 5.1 MHz bandwidth, 10.5 V/µs slew rate, rail-to-rail output, shutdown capability, and 8-PDIP packaging in one engineering-focused reference.
直接替換替代品,適用於 TLV2770IP — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
TLV2770CP
✅ 直接替換📋 參考替代品(不在目錄中)
TLV2770IP 最大額定值與電氣特性
| Amplifier Type | Single operational amplifier |
| Number of Circuits | 1 circuit |
| Supply Voltage Minimum | 2.7 V |
| Supply Voltage Maximum | 5.5 V |
| Gain-Bandwidth Product | 5.1 MHz |
| Slew Rate | 10.5 V/µs |
| Output Topology | Rail-to-rail output |
| Shutdown Function | Supported |
| Operating Temperature Minimum | -40 °C |
| Operating Temperature Maximum | 125 °C |
| Package Type | 8-PDIP |
| 腳位數 | 8 pins |
| 安裝類型 | Through-hole |
TLV2770IP 8-pdip 腳位配置指南
TLV2770IP(8-pdip 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: TLV2770IP.
請參閱 資料表 以查看完整腳位配置。
典型應用
TLV2770IP 適用於 6 應用s: Low-Voltage Sensor Signal Conditioning, Active Low-Pass Filtering, Audio Preamplification, Battery-Powered Instrumentation, Industrial Control Signal Interface, Portable Data-Acquisition Module.
Low-Voltage Sensor Signal Conditioning
The TLV2770IP fits sensor front ends that require more bandwidth than a slow general-purpose amplifier but do not need a high-voltage supply. Its 5.1 MHz gain-bandwidth product and 10.5 V/µs slew rate provide useful dynamic range for pressure, temperature, and position-sensor signals operating from 2.7 V to 5.5 V. Place the amplifier in a non-inverting or differential conditioning stage, then keep sensor return paths and feedback resistors close to the device to limit parasitic pickup. Verify the input common-mode range against the sensor output and include filtering where sensor bandwidth is lower than the amplifier bandwidth.
推薦
Active Low-Pass Filtering
The TLV2770IP can implement an active low-pass filter in a 3.3 V or 5 V analog subsystem because its 5.1 MHz gain-bandwidth product leaves bandwidth above many practical filter cutoffs. The 10.5 V/µs slew rate also helps the output follow filter transitions without excessive delay for moderate signals. Build the filter around the device's prescribed noise-gain network, and place the operational amplifier, feedback components, and signal nodes close together to reduce board-level interference. Confirm noise, offset, common-mode behavior, and capacitor tolerances in the datasheet when the filter has high stopband attenuation requirements.
推薦
Audio Preamplification
The TLV2770IP is applicable to low-voltage audio preamplifier stages where the 10.5 V/µs slew rate is preferable to the response of a low-bandwidth general-purpose op amp. Rail-to-rail output can increase the usable signal range in 2.7 V to 5.5 V single-supply systems, while the 5.1 MHz gain-bandwidth product supports audio-band closed-loop gains with practical bandwidth margin. The shutdown feature may reduce power consumption when the signal path is inactive. Headroom, output-current capability, noise, and distortion must be checked against the headphone, line, or speaker load before finalizing the stage.
推薦
Battery-Powered Instrumentation
The TLV2770IP suits low-power instrumentation built around a 3.3 V or 5 V rail because it starts at 2.7 V and includes a shutdown function. The 5.1 MHz gain-bandwidth product and 10.5 V/µs slew rate allow the device to serve as a signal buffer, gain stage, or active filter rather than merely a precision DC amplifier. Shutdown can reduce activity when a measurement cycle is complete, but timing and logic levels must be controlled carefully. Use short supply paths, local decoupling, and a quiet ground reference to prevent the faster amplifier from amplifying board noise or switching transients.
推薦
Industrial Control Signal Interface
The TLV2770IP can condition low-level control signals in industrial equipment operating from a 2.7 V to 5.5 V rail. Its rail-to-rail output and 10.5 V/µs slew rate are useful for driving downstream analog or mixed-signal stages through moderate impedances, while the 5.1 MHz bandwidth supports faster control-loop or interface signals. Maintain a common ground reference between the source and amplifier, protect external wiring from transients, and avoid driving long capacitive cables directly from the output without isolation or buffering. Review output-current and capacitive-load limits before using the device near connector or relay-driver circuits.
推薦
Portable Data-Acquisition Module
The TLV2770IP is a practical fit for portable data-acquisition modules that need signal conditioning from a low-voltage battery-regulated supply. Its 5.1 MHz gain-bandwidth product supports moderately fast analog channels, and the shutdown capability can help a multichannel design isolate inactive circuitry. Use the amplifier for gain, current-to-voltage conversion, or active filtering, depending on the source impedance and required bandwidth. High-impedance sensors may require attention to bias current and offset, while ADC-driving paths require checking capacitive loading and settling behavior. Keep the analog return path compact and isolate fast digital switching from the signal input.
推薦
工程參考資料,適用於 TLV2770IP — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | TLV2770CP |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-PDIP | 8-PDIP - same package |
| Amplifier Type | Single rail-to-rail output operational amplifier | Single rail-to-rail output operational amplifier |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Gain-Bandwidth Product | 5.1 MHz | 5.1 MHz |
| Slew Rate | 10.5 V/µs | 10.5 V/µs |
| Shutdown Function | Supported | Supported |
| Operating Temperature Range | -40 °C to 125 °C | -40 °C to 125 °C |
| Pin Compatibility | 8-PDIP pin configuration | Consistent terminals; no circuit modification required |
主要差異化特點
- High-speed operation in an 8-PDIP analog package (對比TLV2770CP)
- Rail-to-rail output for low-voltage analog systems (對比TLV2770CP)
- Integrated shutdown for power management (對比TLV2770CP)
設計說明
Operate the TLV2770IP only within its 2.7 V to 5.5 V specified supply range. Place the supply-decoupling capacitor close to the power pins and use the manufacturer-recommended network and capacitor type. Treat the shutdown control as a sequencing input: its permitted voltage and transition behavior should be verified before tying it to a microcontroller or power-management signal. Keeping the power loop compact helps the 5.1 MHz bandwidth stage remain stable in practical layouts.
Route the op-amp input, feedback, and output paths to minimize loop area and susceptibility to switching noise. Place high-value feedback resistors close to the relevant device pins where practical, and keep the analog signal path away from clock and power-converter routing. Because the 10.5 V/µs slew rate can respond quickly to unwanted coupling, use a quiet return path and controlled board stackup. Validate the finished layout with stability and signal-integrity measurements.
Do not select the amplifier from bandwidth and slew rate alone. Check input common-mode range, offset voltage, bias current, noise, output-current capability, capacitive-load behavior, and shutdown logic for the intended circuit. A 5.1 MHz gain-bandwidth product does not guarantee 5.1 MHz operation at every closed-loop gain, and rail-to-rail output does not mean the input common-mode range reaches both rails. Use the device-specific manufacturer datasheet as the final electrical-selection reference.
合規資訊
The manufacturer and distributor records identify the TLV2770IP and its operating characteristics but do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. These fields therefore remain unknown.