TLV2770IP - 5.1MHz Rail-to-Rail Op Amp | Texas Instruments
Référence : TLV2770IP ✓ ActifTLV2770IP Présentation
An operational amplifier, commonly called an op amp, is a voltage-gain element used to amplify small signals, buffer high-impedance sources, compare voltages, or drive analog stages. The TLV2770 belongs to the single-amplifier family within the broader hierarchy of analog integrated circuits, analog signal-chain ICs, and power-management-aware semiconductor designs. Its rail-to-rail output stage is intended to produce useful output voltage closer to the supply rails than a conventional output stage.
The headline characteristics are a 5.1 MHz gain-bandwidth product, a 10.5 V/µs slew rate, and operation from 2.7 V to 5.5 V. These specifications suit applications such as sensor-signal conditioning, active filtering, audio preamplification, and general-purpose analog buffers. The shutdown function provides a way to reduce power use when the amplifier is not needed, which can be useful in portable and intermittently powered systems.
Technically, gain-bandwidth product describes the relationship between closed-loop gain and bandwidth, while slew rate limits how quickly the output can move through large voltage changes. The TLV2770's combination favors relatively fast small-signal operation and reasonably clean large-signal transitions. Designers should still verify noise, input-offset voltage, output-current capability, stability, and load behavior against their exact operating conditions before releasing a production design.
Typical applications include low-voltage sensor interfaces, precision current-feedback signal paths, active low-pass filters, audio input stages, battery-powered instrumentation, and general analog signal conditioning. The 8-PDIP through-hole package is useful for prototypes, educational platforms, repair assemblies, and designs where a socketed DIP footprint is preferred over a compact surface-mount package.
A key design consideration is bypassing the supply pins with short, low-inductance connections and placing stable input and feedback networks close to the amplifier. Confirm the shutdown-pin logic and timing in the manufacturer datasheet before using the device for power sequencing. Because this is an analog IC rather than a power semiconductor, a safe operating area chart is not applicable.
This product record combines manufacturer and distributor information with application guidance, comparison parameters, and practical design notes. It highlights the TLV2770IP's 2.7 V minimum supply, 5.5 V maximum supply, 5.1 MHz bandwidth, 10.5 V/µs slew rate, rail-to-rail output, shutdown capability, and 8-PDIP packaging in one engineering-focused reference.
Alternatives de remplacement direct pour TLV2770IP — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
TLV2770CP
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TLV2770IP Valeurs maximales et caractéristiques électriques
| Amplifier Type | Single operational amplifier |
| Number of Circuits | 1 circuit |
| Supply Voltage Minimum | 2.7 V |
| Supply Voltage Maximum | 5.5 V |
| Gain-Bandwidth Product | 5.1 MHz |
| Slew Rate | 10.5 V/µs |
| Output Topology | Rail-to-rail output |
| Shutdown Function | Supported |
| Operating Temperature Minimum | -40 °C |
| Operating Temperature Maximum | 125 °C |
| Package Type | 8-PDIP |
| Nombre de broches | 8 pins |
| Type de montage | Through-hole |
Guide de configuration des broches du TLV2770IP 8-pdip
Configuration des broches du TLV2770IP (boîtier 8-pdip). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour TLV2770IP.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
TLV2770IP convient pour 6 applications: Low-Voltage Sensor Signal Conditioning, Active Low-Pass Filtering, Audio Preamplification, Battery-Powered Instrumentation, Industrial Control Signal Interface, Portable Data-Acquisition Module.
Low-Voltage Sensor Signal Conditioning
The TLV2770IP fits sensor front ends that require more bandwidth than a slow general-purpose amplifier but do not need a high-voltage supply. Its 5.1 MHz gain-bandwidth product and 10.5 V/µs slew rate provide useful dynamic range for pressure, temperature, and position-sensor signals operating from 2.7 V to 5.5 V. Place the amplifier in a non-inverting or differential conditioning stage, then keep sensor return paths and feedback resistors close to the device to limit parasitic pickup. Verify the input common-mode range against the sensor output and include filtering where sensor bandwidth is lower than the amplifier bandwidth.
Recommandé
Active Low-Pass Filtering
The TLV2770IP can implement an active low-pass filter in a 3.3 V or 5 V analog subsystem because its 5.1 MHz gain-bandwidth product leaves bandwidth above many practical filter cutoffs. The 10.5 V/µs slew rate also helps the output follow filter transitions without excessive delay for moderate signals. Build the filter around the device's prescribed noise-gain network, and place the operational amplifier, feedback components, and signal nodes close together to reduce board-level interference. Confirm noise, offset, common-mode behavior, and capacitor tolerances in the datasheet when the filter has high stopband attenuation requirements.
Recommandé
Audio Preamplification
The TLV2770IP is applicable to low-voltage audio preamplifier stages where the 10.5 V/µs slew rate is preferable to the response of a low-bandwidth general-purpose op amp. Rail-to-rail output can increase the usable signal range in 2.7 V to 5.5 V single-supply systems, while the 5.1 MHz gain-bandwidth product supports audio-band closed-loop gains with practical bandwidth margin. The shutdown feature may reduce power consumption when the signal path is inactive. Headroom, output-current capability, noise, and distortion must be checked against the headphone, line, or speaker load before finalizing the stage.
Recommandé
Battery-Powered Instrumentation
The TLV2770IP suits low-power instrumentation built around a 3.3 V or 5 V rail because it starts at 2.7 V and includes a shutdown function. The 5.1 MHz gain-bandwidth product and 10.5 V/µs slew rate allow the device to serve as a signal buffer, gain stage, or active filter rather than merely a precision DC amplifier. Shutdown can reduce activity when a measurement cycle is complete, but timing and logic levels must be controlled carefully. Use short supply paths, local decoupling, and a quiet ground reference to prevent the faster amplifier from amplifying board noise or switching transients.
Recommandé
Industrial Control Signal Interface
The TLV2770IP can condition low-level control signals in industrial equipment operating from a 2.7 V to 5.5 V rail. Its rail-to-rail output and 10.5 V/µs slew rate are useful for driving downstream analog or mixed-signal stages through moderate impedances, while the 5.1 MHz bandwidth supports faster control-loop or interface signals. Maintain a common ground reference between the source and amplifier, protect external wiring from transients, and avoid driving long capacitive cables directly from the output without isolation or buffering. Review output-current and capacitive-load limits before using the device near connector or relay-driver circuits.
Recommandé
Portable Data-Acquisition Module
The TLV2770IP is a practical fit for portable data-acquisition modules that need signal conditioning from a low-voltage battery-regulated supply. Its 5.1 MHz gain-bandwidth product supports moderately fast analog channels, and the shutdown capability can help a multichannel design isolate inactive circuitry. Use the amplifier for gain, current-to-voltage conversion, or active filtering, depending on the source impedance and required bandwidth. High-impedance sensors may require attention to bias current and offset, while ADC-driving paths require checking capacitive loading and settling behavior. Keep the analog return path compact and isolate fast digital switching from the signal input.
Recommandé
Données de référence d'ingénierie pour TLV2770IP — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | TLV2770CP |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-PDIP | 8-PDIP - same package |
| Amplifier Type | Single rail-to-rail output operational amplifier | Single rail-to-rail output operational amplifier |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Gain-Bandwidth Product | 5.1 MHz | 5.1 MHz |
| Slew Rate | 10.5 V/µs | 10.5 V/µs |
| Shutdown Function | Supported | Supported |
| Operating Temperature Range | -40 °C to 125 °C | -40 °C to 125 °C |
| Pin Compatibility | 8-PDIP pin configuration | Consistent terminals; no circuit modification required |
Principaux différenciateurs
- High-speed operation in an 8-PDIP analog package (vs TLV2770CP)
- Rail-to-rail output for low-voltage analog systems (vs TLV2770CP)
- Integrated shutdown for power management (vs TLV2770CP)
Notes de conception
Operate the TLV2770IP only within its 2.7 V to 5.5 V specified supply range. Place the supply-decoupling capacitor close to the power pins and use the manufacturer-recommended network and capacitor type. Treat the shutdown control as a sequencing input: its permitted voltage and transition behavior should be verified before tying it to a microcontroller or power-management signal. Keeping the power loop compact helps the 5.1 MHz bandwidth stage remain stable in practical layouts.
Route the op-amp input, feedback, and output paths to minimize loop area and susceptibility to switching noise. Place high-value feedback resistors close to the relevant device pins where practical, and keep the analog signal path away from clock and power-converter routing. Because the 10.5 V/µs slew rate can respond quickly to unwanted coupling, use a quiet return path and controlled board stackup. Validate the finished layout with stability and signal-integrity measurements.
Do not select the amplifier from bandwidth and slew rate alone. Check input common-mode range, offset voltage, bias current, noise, output-current capability, capacitive-load behavior, and shutdown logic for the intended circuit. A 5.1 MHz gain-bandwidth product does not guarantee 5.1 MHz operation at every closed-loop gain, and rail-to-rail output does not mean the input common-mode range reaches both rails. Use the device-specific manufacturer datasheet as the final electrical-selection reference.
Informations de conformité
The manufacturer and distributor records identify the TLV2770IP and its operating characteristics but do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. These fields therefore remain unknown.