TPS2371PWR - Legacy PoE Power Interface Switch | TI
Teilenummer: TPS2371PWR ✗ Abgekündigt| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $0 | $0,00 |
| 10 | $0 | $0,00 |
| 100 | $0 | $0,00 |
| 500 | $0 | $0,00 |
| 1.000 | $0 | $0,00 |
| 3.000 | $0 | $0,00 |
TPS2371PWR Übersicht
A power interface switch is an integrated semiconductor that sits between a PoE source and the powered equipment. It controls how power is applied to the downstream circuit, helping prevent excessive startup current, protecting source equipment, and defining the operating conditions seen by the load. In the broader power-management hierarchy, this device belongs to the PoE interface-switch and power-management IC category rather than a conventional voltage regulator.
The verified manufacturer information identifies the TPS2371 as a legacy IEEE 802.3af-compatible power interface switch for PoE PDs. The datasheet search result also states that IEEE 802.3af permits an inrush current of 400 mA for 50 ms, limiting the load capacitor to approximately 180 µF. The programmable inrush current limit removes that restriction and permits a larger capacitor with lower startup current.
The key design trade-off is between fast startup and controlled power admission. A lower programmed inrush limit can reduce stress on the PoE source and downstream components but may lengthen startup, while a higher limit can start a larger load more quickly but places greater transient demand on the source. The device is intended to simplify legacy PoE PD power-interface designs while preserving the external 8-TSSOP footprint.
Typical applications include legacy PoE powered devices, powered Ethernet endpoints, IP cameras, VoIP phones, access-point equipment, and other IEEE 802.3af-compatible PDs. The part should be selected only after checking the source's PoE classification, available power, startup timing, protection requirements, and downstream capacitance against the complete manufacturer datasheet.
For implementation, follow the manufacturer application guidance for input capacitance, current-limit programming, surge protection, layout, and exposed-pad or thermal requirements where applicable. Do not infer ratings, thresholds, or timing values from distributor descriptions alone; verify them in the official TPS2371 datasheet before releasing a production design.
This page consolidates verified manufacturer and distributor descriptions, separates documented facts from unavailable parameters, and provides engineering guidance for comparing this legacy PoE interface switch with possible replacements.
Drop-in-Alternativen für TPS2371PWR – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit TPS2371PWR (gleiche Bauform und Footprint) – abweichend in Package, Product Type, Inrush Current Control, Operating Temperature Range.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
TPS2371PWRG4
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
TPS2371D
✅ Drop-In✓ Auf Lager
Preis auf Anfrage
Datenblatt ansehen →TPS2371PW
✅ Drop-In✓ Auf Lager
$1.12 / Stück
Datenblatt ansehen →TPS2371PWR Grenzwerte & elektrische Eigenschaften
| Product Type | Power interface switch for Power over Ethernet powered devices |
| PoE Compatibility | Legacy IEEE 802.3af compatible |
| Gehäuse | 8-TSSOP, 0.173 inch / 4.40 mm width |
| Pin-Anzahl | 8 pins |
| Input Inrush Limit | 400 mA for 50 ms according to IEEE 802.3af specification |
| Maximum Load Capacitor Under IEEE 802.3af Limit | Approximately 180 µF |
| Inrush Current Control | Programmable |
| Betriebstemperaturbereich | 0°C to 70°C |
| Montageart | Surface mount |
| Manufacturer | Texas Instruments |
| Lifecycle Classification | Legacy |
| Application Category | Power over Ethernet powered devices |
| Schnittstellentyp | PoE power interface |
TPS2371PWR 8-tssop, 0.173 inch / 4.40 mm width Pinbelegungsleitfaden
Pinbelegung für TPS2371PWR (8-tssop, 0.173 inch / 4.40 mm width-Gehäuse). Dieses Leistungsbauteil verfügt über Gate-, Drain- und Source-Anschlüsse. Bei nicht gepolten Gehäusen entnehmen Sie die genaue Ausrichtung von Pin 1 und Footprint-Details dem Herstellerdatenblatt. Typische Anwendungen sind Netzteilentwurf, Motoransteuerung und Lastschaltung.
Keine detaillierten Pinbelegungsdaten verfügbar für TPS2371PWR.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
TPS2371PWR ist geeignet für 6 Anwendungs: Legacy PoE IP Camera, VoIP Phone Power Interface, Powered Wireless Access Point, Industrial PoE Sensor Gateway, Legacy PoE Network Interface, Low-Power PoE Endpoint.
Legacy PoE IP Camera
TPS2371PWR is suitable for a legacy IEEE 802.3af powered IP camera when the system needs controlled startup of its local input capacitance. The switch's programmable inrush function is important because a camera can contain bulk capacitance, regulators, filters, and power-hold-up components that would otherwise create a large startup transient. Using a lower programmed inrush level can reduce stress on the PoE source, while a higher level can shorten startup when the power budget permits. The verified record confirms legacy PoE compatibility and programmable limiting, but it does not provide the complete current-limit range, input voltage range, or timing values. Validate the camera's capacitor size, power budget, and startup sequence against the official datasheet.
Empfohlen
VoIP Phone Power Interface
TPS2371PWR can be considered in a legacy PoE VoIP phone or access endpoint where the powered device receives power through an Ethernet connection. The programmable inrush feature helps separate the initial charging event from the normal operating load, allowing the designer to choose a startup profile that does not excessively burden the source. This is useful in designs with local decoupling and regulator input capacitors. The verified data identifies an 8-TSSOP package and legacy IEEE 802.3af compatibility, but it does not specify telephone power classes, startup time, or maximum operating current. Those values must be obtained from the manufacturer datasheet before selecting the device for a production phone.
Empfohlen
Powered Wireless Access Point
TPS2371PWR may fit a legacy PoE wireless access point that needs controlled admission of power before its RF, digital, and memory circuits start. The switch's inrush-current programming helps the designer manage a load with multiple local capacitors and regulators, reducing the chance that startup energy will trip or stress the upstream PoE source. A lower limit may extend startup, while a higher limit may improve boot time; the correct setting depends on the source capability and load capacitance. The verified data confirms legacy IEEE 802.3af compatibility and programmable inrush behavior but does not provide the device's current-limit range, input voltage limits, or thermal data.
Empfohlen
Industrial PoE Sensor Gateway
TPS2371PWR can be evaluated in a legacy PoE sensor gateway when the powered equipment includes a large input capacitor or multiple supply rails. The switch provides a controlled path for applying power rather than allowing an uncontrolled inrush event. That benefit is especially relevant when the gateway includes wireless, analog, or digital subsystems that become active only after power is stable. However, the verified record does not establish industrial temperature qualification, input-voltage tolerance, surge protection, or AEC-Q100 status. The gateway design should therefore use the device only after confirming the full electrical envelope and environmental requirements in the official TPS2371 documentation.
Empfohlen
Legacy PoE Network Interface
TPS2371PWR is applicable to a legacy PoE network interface that needs a defined power-on sequence between the Ethernet source and the local circuitry. Programmable inrush current helps coordinate the charging of input capacitance with the source's allowed startup behavior. The part's 8-TSSOP package is useful for compact embedded designs, but board layout must follow the manufacturer recommendations for high-current paths, bypass capacitors, protection, and signal return. The verified data does not provide a complete pinout or all timing thresholds, so engineers should not assign pins or finalize startup timing from the distributor snippets alone.
Empfohlen
Low-Power PoE Endpoint
TPS2371PWR can be considered for a low-power PoE endpoint where controlled startup is more important than adding a modern high-integration power converter. The device separates the source-admission function from the downstream regulator, allowing the powered circuit to use its own voltage regulation while the interface switch manages the initial current event. This can simplify power sequencing and reduce the risk of source overload. The verified material does not provide efficiency, quiescent current, maximum power, or thermal specifications, so the endpoint's average and peak power must be checked against the complete manufacturer datasheet and the selected PoE power class.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für TPS2371PWR – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | TPS2371PWRG4 | TPS2371D | TPS2371PW |
|---|---|---|---|---|
| Product Type | Legacy IEEE 802.3af-compatible PoE PD power interface switch | TPS2371 family power interface switch; similar functional characteristics reported | Power interface switch; comparison result describes consistent characteristics | TPS2371 family variant; consistent characteristics reported |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-TSSOP, 0.173 inch / 4.40 mm width | 8-TSSOP reported by comparison context | SOIC-8 reported by comparison result; physical footprint requires verification | 8-TSSOP family package |
Wichtigste Unterscheidungsmerkmale
- Legacy PoE positioning (vs. TPS23753APW)
- Programmable startup behavior (vs. TPS2350PWR)
- Documented reference limit (vs. TPS2371D)
- Package selection requires validation (vs. TPS2371D)
Designhinweise
Calculate the startup charge requirement from the downstream capacitance and the selected inrush limit before laying out the PoE input stage. The supplied datasheet snippet identifies a 400 mA, 50 ms IEEE 802.3af reference and an approximately 180 µF resulting capacitor limit, but the TPS2371's programmable range is not included in the verified record. Confirm the exact threshold, tolerance, and startup timing in the official datasheet. Then verify that the programmed profile does not cause the source or local regulator to exceed its limits.
Place the input bypass and protection components directly along the PoE power-entry path and keep the high-current return path short and wide. The verified data does not include the complete pinout or recommended land pattern, so do not infer pad assignments from the package name. Use the manufacturer package drawing and application guidance to determine capacitor placement, surge-current routing, and exposed thermal features. Incorrect high-current placement can increase parasitic inductance and undermine the controlled startup behavior.
Do not treat a distributor search result as proof of drop-in compatibility. The cross-reference material names TPS23753APW and TPS2350PWR for comparison, but it does not establish identical pin functions, input limits, current-limit ranges, startup timing, or protection behavior. Before substituting either part, compare the official datasheets and verify the PCB footprint. Also check the device's legacy status and obtain a current lifecycle statement before committing new production designs.
Compliance-Informationen
The supplied verified data does not explicitly state RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 status. AEC-Q100 is marked not_applicable because no automotive qualification claim appears in the verified data, not because the product is confirmed qualified or unqualified for every automotive context.
