TPS54283 - Dual 2A 300kHz Buck Converter | Texas Instruments
Teilenummer: TPS54283 ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $3.89 | $3,89 |
| 10 | $3.46 | $34,60 |
| 100 | $2.98 | $298,00 |
| 500 | $2.52 | $1.260,00 |
| 1.000 | $2.18 | $2.180,00 |
TPS54283 Übersicht
What is a non-synchronous buck converter? A non-synchronous buck converter is a step-down switching regulator that uses an integrated high-side MOSFET as the control switch and an external Schottky diode as the low-side rectifier. Because the TPS54283 integrates the high-side switch, each of its two channels only needs an external Schottky diode, an inductor, and input/output capacitors. In the power management hierarchy it is: DC-DC converter -> non-synchronous buck converter -> step-down switching voltage regulator -> power management IC.
Key features include dual 2-A outputs, a wide 4.5-V to 28-V input range, adjustable output down to 0.8 V, fixed 300-kHz switching, internal compensation, and an integrated high-side MOSFET. The internal error-amplifier compensation removes the external compensation network, reducing BOM count and simplifying loop-stability design. The wide input range gives margin for 5-V, 12-V, and 24-V systems.
From a technical standpoint, the current-mode controlled converter balances inductor size, output ripple, and efficiency at 300 kHz. Because the low-side rectifier is external, a designer can optimize the Schottky diode for forward voltage and thermal behavior. The PowerPAD must be soldered to a solid ground-plane copper area to keep junction temperature within limits at full dual 2-A load.
Typical applications include broadband gateways (DSL/cable modems), IP security cameras, set-top boxes, and industrial control boards that generate a 5-V and a 3.3-V rail from a 12-V or 24-V input. The adjustable output also supports point-of-load power in consumer media devices.
When designing with the TPS54283, verify input-to-output headroom and Schottky diode rating for each channel, and use the exposed thermal pad to a large ground copper pour. Total dissipation is the combined loss of both channels, so thermal layout is critical at 2 A per output.
Drop-in-Alternativen für TPS54283 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
TPS54286PWP
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
TPS54183PWP
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
TPS54383PWP
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
TPS54386PWP
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
TPS54283 Grenzwerte & elektrische Eigenschaften
| Funktion | Dual non-synchronous buck converter |
| Anzahl der Ausgänge | 2 |
| Eingangsspannungsbereich | 4.5 V to 28 V |
| Output Current per Channel | 2 A |
| Ausgangsspannungsbereich | 0.8 V to 90% of VIN |
| Schaltfrequenz | 300 kHz (fixed) |
| Ausgangstyp | Adjustable |
| Integrated High-Side MOSFET | Yes |
| Low-Side Rectifier | External Schottky diode |
| Compensation | Internal |
| Gehäuse / Bauform | 14-PowerTSSOP (HTSSOP-14, PWP) 4.40 mm width |
| Montageart | Surface Mount |
| Thermal Pad | Exposed PowerPAD |
| RoHS | unknown (not provided in verified data) |
TPS54283 14-powertssop (htssop-14, pwp) 4.40 mm width Pinbelegungsleitfaden
Pinbelegung für TPS54283 (14-powertssop (htssop-14, pwp) 4.40 mm width-Gehäuse). Dieses Leistungsbauteil verfügt über Gate-, Drain- und Source-Anschlüsse. Bei nicht gepolten Gehäusen entnehmen Sie die genaue Ausrichtung von Pin 1 und Footprint-Details dem Herstellerdatenblatt. Typische Anwendungen sind Netzteilentwurf, Motoransteuerung und Lastschaltung.
Keine detaillierten Pinbelegungsdaten verfügbar für TPS54283.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
TPS54283 ist geeignet für 6 Anwendungs: Industrial Dual-Rail Power Supply, Broadband Gateway / DSL Modem Power, IP Security Camera Main Board, Set-Top Box / Media Player Power, 12-V Battery-Powered Industrial Equipment, Telecom / Networking Line Card.
Industrial Dual-Rail Power Supply
The TPS54283 is a natural fit for industrial dual-rail power supplies that convert a 24-V or 12-V bus into 5-V and 3.3-V logic rails. With a 4.5-V to 28-V input, each 2-A channel can drive MCU, FPGA, and sensor loads, while the integrated high-side MOSFET and internal compensation minimize external parts. One consideration is thermal: a 24-V to 5-V conversion at 2 A has large VIN-VOUT delta, so use a high-current Schottky diode and a large PowerPAD copper area to keep junction temperature within limits.
Empfohlen
Broadband Gateway / DSL Modem Power
Broadband gateways need multiple clean rails from a 12-V wall adapter. The TPS54283's two 2-A channels can generate 3.3 V for the SoC and 5 V for PHY or USB peripherals. The fixed 300-kHz switching reduces EMI in unshielded plastic enclosures, and internal compensation simplifies the BOM. At 2 A per channel, place the converter near the input connector and keep output traces short to minimize ripple; overall system thermal load should also factor in the adjacent Ethernet PHY and memory components.
Empfohlen
IP Security Camera Main Board
IP cameras powered over PoE use 48-V or 24-V to feed an intermediate 12-V rail, and the TPS54283 can then generate sensor-core and I/O rails. Its 2 A per channel covers CMOS image sensor, ISP, motor, and IR-LED auxiliary loads, while the 300-kHz switching keeps inductor size small for tight PCB form factors. Use the exposed PowerPAD to a ground pour and select a Schottky diode rated above the peak inductor current; the adjustable output also allows fine voltage trimming.
Empfohlen
Set-Top Box / Media Player Power
In set-top boxes and media players, the TPS54283 produces 5 V and 3.3 V from a 12-V adapter. Two 2-A channels are sufficient for the main SoC, DDR memory, Wi-Fi module, and front-end tuner. Internal compensation and integrated high-side MOSFET reduce BOM count and layout risk, and the dual outputs replace two single-channel bucks. Keep the switching node area small and the BOOT capacitor close to the IC; total board dissipation should be reviewed for fanless enclosures at full 2-A load.
Empfohlen
12-V Battery-Powered Industrial Equipment
For battery-powered industrial equipment, the TPS54283 accepts a 12-V nominal battery with input variation from 9 V to 16 V within its 4.5-V to 28-V range. Two 2-A outputs can power a host controller and actuators or I/O. At lower battery voltages the fixed 300-kHz converter still keeps high efficiency; at 4.5-V minimum input, output voltage can still be programmed down to 0.8 V. Use low-ESR ceramic caps and a Schottky diode sized for the maximum inductor ripple current.
Empfohlen
Telecom / Networking Line Card
On telecom line cards, board space is valuable and multiple rails are needed. The TPS54283's dual 2-A outputs generate 3.3 V and 1.8 V or 2.5 V from an intermediate 12-V bus, and the integrated high-side MOSFET keeps switching cells compact. The 300-kHz frequency stabilizes EMI across the card, and internal compensation reduces tuning effort. For higher-current rails, a companion TPS54383PWP (3 A) can be used, keeping the same HTSSOP-14 footprint.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für TPS54283 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | TPS54286PWP | TPS54183PWP | TPS54383PWP | TPS54386PWP |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-PowerTSSOP (HTSSOP-14, PWP) | 14-PowerTSSOP - same | 14-PowerTSSOP - same | 14-PowerTSSOP - same | 14-PowerTSSOP - same |
| Output Current per Channel | 2 A | 2 A | 1 A | 3 A | 3 A |
| Switching Frequency | 300 kHz | 600 kHz | 300 kHz | 300 kHz | 600 kHz |
| Input Voltage Range | 4.5 V to 28 V | 4.5 V to 28 V | 4.5 V to 28 V | 4.5 V to 28 V | 4.5 V to 28 V |
| Output Voltage Range | 0.8 V to 90% of VIN | 0.8 V to 90% of VIN | 0.8 V to 90% of VIN | 0.8 V to 90% of VIN | 0.8 V to 90% of VIN |
| Number of Outputs | 2 | 2 | 2 | 2 | 2 |
| Compensation | Internal | Internal | Internal | Internal | Internal |
Wichtigste Unterscheidungsmerkmale
- Dual 2-A output capability in one 14-pin package (vs. TPS54183PWP)
- Fixed 300-kHz switching with internal compensation (vs. TPS54286PWP)
- Cost-optimized for 2-A dual-rail loads (vs. TPS54383PWP)
Designhinweise
The TPS54283 is supplied in a 14-pin PowerTSSOP with exposed PowerPAD. At 12-V input, 3.3-V/2-A output per channel, total loss can exceed 4 W. Solder the PowerPAD to a large ground-plane copper area (at least 1 in² per channel equivalent) and add thermal vias under the pad to reduce theta_JA. Without proper thermal design, junction temperature may exceed the recommended limit at high ambient.
Place a 10-uF ceramic input capacitor near the VIN pins and a 0.1-uF BOOT capacitor close to BOOT/SW for the high-side gate drive. Use a Schottky diode rated for at least 3 A and low forward voltage, with the diode cathode close to the SW pin and anode to GND. Keep the SW node compact and away from the feedback/sense traces to reduce noise coupling.
Do not exceed 28 V on VIN, and remember the maximum output voltage is 90% of VIN, not rail-to-rail. The outputs are adjustable with an external resistor divider; use 1% resistors. Because the converter is non-synchronous, omitting the external Schottky diode will cause high dissipation and possible damage. Always verify component ratings at the actual peak inductor current.
Compliance-Informationen
Verified web data did not include compliance certificates; confirm with TI product page before claiming compliance.
