TPS78433QWDRBRQ1 - 300mA 3.3V AEC-Q100 LDO | Texas Instruments
Teilenummer: TPS78433QWDRBRQ1 ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $1.18 | $1,18 |
| 10 | $1.06 | $10,60 |
| 100 | $0.94 | $94,00 |
| 500 | $0.85 | $425,00 |
| 1.000 | $0.78 | $780,00 |
| 3.000 | $0.71 | $2.130,00 |
TPS78433QWDRBRQ1 Übersicht
A low-dropout (LDO) regulator is a type of linear voltage regulator that maintains a stable output voltage using a series pass element, even when the input voltage is only slightly higher than the desired output. LDOs sit within the broader hierarchy of voltage regulators under power management ICs, and they are preferred over switching regulators when low noise, small footprint, and fast transient response matter more than conversion efficiency. The TPS78433QWDRBRQ1 targets always-on automotive subsystems where low quiescent current extends standby life on the vehicle battery.
Key features include a low quiescent current that preserves battery life in always-on systems, a high power-supply rejection ratio (PSRR) that attenuates upstream switching-converter ripple, and high output-voltage accuracy across line, load, and temperature. The device also integrates an active-high enable pin that supports power sequencing in multi-rail systems and a thermal-shutdown block that protects the die under fault conditions. The compact VSON-8 footprint suits module-level PCB layouts with strict area budgets.
Technically, the TPS784-Q1 family uses a PMOS pass topology to achieve low dropout, and its internal reference and feedback network are trimmed for tight initial accuracy. Stability is maintained with small ceramic output capacitors, simplifying BOM cost and PCB area. The wide operating range and automotive-grade qualification allow direct use under the hood, in body controllers, and in advanced driver-assistance system (ADAS) sensor supplies.
Typical applications include automotive camera modules, body and chassis controllers, ADAS sensor rails, infotainment head-unit auxiliary supplies, and always-on microcontroller rails in cluster and telematics modules. The fixed 3.3 V output suits low-power MCUs and CAN/LIN transceivers directly.
When designing with this device, ensure the input-to-output headroom is sufficient to keep the LDO in regulation at maximum load, and place input/output ceramic capacitors close to the pins. For applications sharing an automotive battery feed, follow OEM load-dump and reverse-battery protection guidance around the LDO input. This page synthesizes distributor pricing, AEC-Q100 drop-in alternatives, and practical automotive design notes not bundled in the manufacturer datasheet alone.
Drop-in-Alternativen für TPS78433QWDRBRQ1 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
TPS78430QWDRBRQ1
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
TPS78425QWDRBRQ1
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
TPS78418QWDRBRQ1
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
TPS7A2010PDBVR
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
TLV70033DDCR
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
TPS78433QWDRBRQ1 Grenzwerte & elektrische Eigenschaften
| Ausgangstyp | Fixed (3.3 V) |
| Ausgangsspannung | 3.3 V |
| Output Voltage Accuracy | 1.5% (typical, over line/load/temperature) |
| Maximaler Ausgangsstrom | 300 mA |
| Eingangsspannungsbereich | 1.65 V to 6.0 V |
| Enable-Pin | Yes (active-high) |
| Thermisches Abschalten | Yes (integrated) |
| Operating Temperature (Ambient, TA) | -40 °C to +125 °C |
| Junction Temperature Range (TJ) | -40 °C to +150 °C |
| Gehäuse | VSON-8 (DRB) 3 x 3 mm |
| Montageart | Surface Mount |
| RoHS-Status | Compliant |
| AEC-Q100 Grade | Grade 1 (qualified for automotive) |
TPS78433QWDRBRQ1 Pin-Konfiguration
| Pin 1 | IN — Input voltage supply |
| Pin 2 | IN — Input voltage supply (tied to pin 1) |
| Pin 3 | EN — Enable (active-high) |
| Pin 4 | NC — Not connected (per datasheet) |
| Pin 5 | GND — Ground |
| Pin 6 | NC — Not connected (per datasheet) |
| Pin 7 | OUT — Regulated 3.3 V output |
| Pin 8 | OUT — Regulated 3.3 V output (tied to pin 7) |
| Pin EP | PAD — Exposed thermal pad - connect to GND for thermal dissipation |
Typische Anwendungen
TPS78433QWDRBRQ1 ist geeignet für 6 Anwendungs: Automotive Camera Module Power, Body and Chassis Controllers, ADAS Sensor Power (Radar/LiDAR), Infotainment Auxiliary Supplies, Cluster and Telematics MCU Rails, Industrial IoT Gateways with Automotive Heritage.
Automotive Camera Module Power
The TPS78433QWDRBRQ1 delivers a clean fixed 3.3 V rail for automotive front, rear, and surround-view camera modules. Its 300 mA continuous rating easily supports image-sensor AVDD plus serializer logic, and AEC-Q100 Grade 1 qualification covers underhood and behind-bumper thermal stress. Compared with a switching regulator, the LDO adds no EMI switching noise into the image-sensor analog path, which preserves SNR in low-light conditions. The VSON-8 (DRB) 3 x 3 mm footprint fits the tight module stack-up of compact automotive cameras.
Empfohlen
Body and Chassis Controllers
Body controllers (BCM), door modules, and chassis ECUs use 3.3 V rails for MCUs, CAN/LIN transceivers, and load-driver logic. The TPS78433QWDRBRQ1's wide 1.65 V to 6.0 V input lets the rail ride directly on a 5 V pre-regulated bus or a loosely regulated battery feed, while the active-high enable pin supports ignition-aware power sequencing. AEC-Q100 Grade 1 ensures reliable operation in sealed under-dash modules that can see ambient swings to +125 °C. The exposed-pad VSON-8 package provides low thermal resistance for continuous 300 mA bias currents.
Empfohlen
ADAS Sensor Power (Radar/LiDAR)
Advanced driver-assistance sensor boards require low-noise, post-regulated rails for analog front-ends and high-speed serializers. The TPS78433QWDRBRQ1's high PSRR attenuates ripple from upstream automotive buck regulators, protecting radar MMIC and LiDAR photodiode analog paths. The 300 mA rating covers combined analog + digital blocks, and AEC-Q100 Grade 1 supports behind-grille and roof-mount sensor placement. The fixed 3.3 V output eliminates external feedback components, reducing PCB area on space-constrained sensor PCBs.
Empfohlen
Infotainment Auxiliary Supplies
Infotainment head units and rear-seat entertainment modules draw auxiliary 3.3 V rails for HMI microcontrollers, audio DSPs, and display backlight drivers. The TPS78433QWDRBRQ1's low quiescent current preserves quiescent battery drain when the infotainment system is in standby, while the 300 mA capability supports peak DSP and backlight bursts. The VSON-8 (DRB) footprint suits the dense multi-layer PCBs of head-unit mainboards.
Empfohlen
Cluster and Telematics MCU Rails
Instrument clusters, gateway ECUs, and telematics control units need always-on 3.3 V rails for low-power microcontrollers and CAN-FD transceivers. The TPS78433QWDRBRQ1's low-IQ architecture minimizes quiescent battery drain during key-off, which is critical for OEM quiescent-current budgets. AEC-Q100 Grade 1 supports behind-dash mounting, and the 6.0 V maximum VIN tolerates load-dump transients when paired with an upstream protection network.
Empfohlen
Industrial IoT Gateways with Automotive Heritage
Industrial IoT and fleet-management gateways that benefit from automotive-grade reliability can use the TPS78433QWDRBRQ1 as a robust 3.3 V rail for MCUs and NB-IoT/LTE-M modems. Its wide temperature range and AEC-Q100 qualification deliver automotive-grade resilience in harsh industrial cabinets. The VSON-8 (DRB) footprint is footprint-compatible with industrial designs migrating from commercial-grade LDOs, and the enable pin supports module-level power gating.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für TPS78433QWDRBRQ1 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | TPS78430QWDRBRQ1 | TPS78425QWDRBRQ1 | TPS78418QWDRBRQ1 | TPS7A2010PDBVR | TLV70033DDCR |
|---|---|---|---|---|---|---|
| Package | VSON-8 (DRB) 3x3 mm | VSON-8 (DRB) 3x3 mm - same | VSON-8 (DRB) 3x3 mm - same | VSON-8 (DRB) 3x3 mm - same | SOT-23-5 (DBV) - different footprint | SOT-23-5 (DDC) - different footprint |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Output Voltage | 3.3 V fixed | 3.0 V fixed | 2.5 V fixed | 1.8 V fixed | Adjustable | 3.3 V fixed |
| Output Current | 300 mA | 300 mA | 300 mA | 300 mA | 300 mA | 200 mA |
| Input Voltage Range | 1.65 V to 6.0 V | 1.65 V to 6.0 V | 1.65 V to 6.0 V | 1.65 V to 6.0 V | 1.5 V to 6.0 V (max 18 V transient on TPS7A20 family) | 2.0 V to 5.5 V |
| AEC-Q100 Qualification | Grade 1 (-40C to +125C ambient) | Grade 1 (-40C to +125C ambient) | Grade 1 (-40C to +125C ambient) | Grade 1 (-40C to +125C ambient) | Grade 1 (TPS7A20 family automotive variant) | Not automotive qualified |
| Enable Pin | Yes | Yes | Yes | Yes | Yes | Yes |
| Output Capacitor Type | Ceramic (low ESR) | Ceramic (low ESR) | Ceramic (low ESR) | Ceramic (low ESR) | Ceramic (low ESR) | Ceramic (low ESR) |
Wichtigste Unterscheidungsmerkmale
- AEC-Q100 Grade 1 qualified with VSON-8 exposed-pad thermal footprint (vs. TLV70033DDCR)
- Higher 300 mA continuous output rating in VSON-8 (vs. TPS7A2010PDBVR)
- Wide 1.65 V to 6.0 V input range with low IQ (vs. TLV70033DDCR)
Designhinweise
Estimated: At VIN = 5.0 V, VOUT = 3.3 V, and 300 mA full load, power dissipation is (5.0 - 3.3) * 0.3 = 0.51 W. The VSON-8 (DRB) 3 x 3 mm package dissipates this through the exposed thermal pad; the datasheet theta_JA figure should be confirmed for the actual PCB copper area. For continuous 300 mA bias at +85 °C ambient, attach the EP pad to a GND copper pour of at least 1 square inch with thermal vias to maintain junction temperature below +150 °C.
Place the input and output ceramic capacitors as close as possible to the IN and OUT pins of the TPS78433QWDRBRQ1 to minimize parasitic inductance. Use a 1 µF X7R ceramic on the input and a 1 µF X7R ceramic on the output as a starting point, and confirm stability with the actual PCB layout. The enable pin (EN) should be tied to IN via a 100 kΩ pull-up if not driven by an MCU GPIO, and a 0.1 µF bypass cap on EN improves noise immunity.
Do not assume the TPS78433QWDRBRQ1's 6.0 V absolute-max VIN survives an automotive load-dump event; add a TVS clamp or upstream pre-regulator for 12 V battery systems. Avoid reverse-battery polarity on VIN - automotive designs typically include a series diode or P-FET reverse-protection block. Verify the EN pin voltage never exceeds its absolute-max rating, especially during transients.
Compliance-Informationen
AEC-Q100 Grade 1 qualified per TI product page ('Automotive, 300-mA, low-IQ, high-PSRR, LDO voltage regulator with high accuracy and enable'). RoHS compliance confirmed via TI product page; halogen-free status not explicitly listed in the verified web data and set to 'unknown'.
