XCF16PVO48C0973 - 16Mb FPGA Configuration PROM | AMD Xilinx
Teilenummer: XCF16PVO48C0973 ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $14.26 | $14,26 |
| 10 | $12.83 | $128,30 |
| 100 | $10.95 | $1.095,00 |
| 500 | $9.42 | $4.710,00 |
| 1.000 | $8.2 | $8.200,00 |
XCF16PVO48C0973 Übersicht
A configuration PROM is a non-volatile serial memory that holds the FPGA bitstream and presents it to the FPGA at power-up, after reset, or on demand through JTAG/Serial-mode commands. Compared to parallel flash, configuration PROMs deliver a smaller footprint, simpler interface timing, and proven Xilinx ecosystem compatibility - making them a reference solution for legacy and current Spartan-3, Virtex-4/5, and CoolRunner-II designs that still rely on dedicated boot storage.
Key features of the XCF16PVO48C0973 include 16-Mbit (16Mx1 serial organization) density, in-system programmability through the JTAG/standard Xilinx PROM programming interface, low standby current typical of serial PROMs, and a 48-TSOP package with a 0.724 inch (18.40 mm) body width. The part supports master-serial configuration modes and provides CRC-based bitstream integrity checking during FPGA load.
From an architecture perspective, the device uses a serial-NOR-style command set with opcode-driven read operations, and integrates Xilinx-specific configuration flow states (e.g., 8-bit address counters, bitstream framing) that allow the FPGA to load its image directly without an external microcontroller. This eliminates boot firmware complexity in most FPGA designs.
Typical applications include Spartan-3/3E/6 FPGA boot storage, Virtex-4/5 configuration backup, industrial controller FPGA subsystems, military/aerospace rad-tolerant FPGA designs (when paired with rad-hard FPGAs), and remote field-upgradeable embedded systems that need reliable in-system re-programmability over the JTAG port.
When designing with this PROM, verify the FPGA-to-PROM pin mapping against the target FPGA's Master Serial configuration mode table, ensure the 1.8V rail meets PROM inrush current during read bursts, and place a 0.1 uF + bulk capacitor pair within 5 mm of the VCC pins to maintain clean read-clock edges.
This page synthesizes current distributor pricing, in-system programming guidance, and pin-compatible alternatives across the Xilinx XCF family - content not aggregated on individual distributor listings.
Drop-in-Alternativen für XCF16PVO48C0973 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit XCF16PVO48C0973 (gleiche Bauform und Footprint) – abweichend in Memory Size, Programmable Type, Interface, Memory Type, Package.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
XCF16PVOG48C
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$45.1 / Stück
Datenblatt ansehen →XCF08PVOG48C
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
XCF32PVOG48C
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$19.85 / Stück
Datenblatt ansehen →XC18V04PC44C
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
XCF16PVO48C0973 Grenzwerte & elektrische Eigenschaften
| Speichergröße | 16 Mb (16M x 1 serial) |
| Memory Organization | 16M x 1 (serial) |
| Programmable Type | In System Programmable |
| Funktion | Configuration PROM for FPGAs |
| Supply Voltage Range | 1.65 V to 2.0 V |
| Betriebstemperaturbereich | -40 C to +85 C (TA) |
| Gehäuse / Bauform | 48-TFSOP (0.724 inch, 18.40 mm width) |
| Montageart | Surface Mount |
| Packaging | Bulk / Tray |
| Product Status | Active |
| Configuration Interface | Serial (Master Serial / JTAG) |
| Bitstream Integrity | CRC check during FPGA load |
| Compatible FPGA Families | Spartan-3, Spartan-3E, Spartan-6, Virtex-4, Virtex-5, CoolRunner-II |
XCF16PVO48C0973 Pin-Konfiguration
| Pin 1 | VCC — 1.8V supply |
| Pin 2 | GND — Ground |
| Pin 3 | CCK — Configuration clock input to PROM |
| Pin 4 | DIN — Serial data input from FPGA/chain |
| Pin 5 | DOUT — Serial data output to FPGA |
| Pin 6 | TDI — JTAG test data in |
| Pin 7 | TDO — JTAG test data out |
| Pin 8 | TMS — JTAG test mode select |
| Pin 9 | TCK — JTAG test clock |
| Pin 10 | CEO — Chip enable output (cascade) |
| Pin 11 | CE — Chip enable input |
| Pin 12 | OE/RESET — Output enable / reset |
| Pin 13 | DONE — FPGA DONE indicator (informational) |
| Pin 14 | INIT — FPGA INIT status (informational) |
| Pin 15 | NC — Not connected (per datasheet) |
| Pin 16 | NC — Not connected (per datasheet) |
| Pin 17 | VCC — 1.8V supply |
| Pin 18 | GND — Ground |
| Pin 19 | NC — Not connected (per datasheet) |
| Pin 20 | NC — Not connected (per datasheet) |
| Pin 21 | NC — Not connected (per datasheet) |
| Pin 22 | NC — Not connected (per datasheet) |
| Pin 23 | NC — Not connected (per datasheet) |
| Pin 24 | NC — Not connected (per datasheet) |
| Pin 25 | VCC — 1.8V supply |
| Pin 26 | GND — Ground |
| Pin 27 | NC — Not connected (per datasheet) |
| Pin 28 | NC — Not connected (per datasheet) |
| Pin 29 | NC — Not connected (per datasheet) |
| Pin 30 | NC — Not connected (per datasheet) |
| Pin 31 | NC — Not connected (per datasheet) |
| Pin 32 | NC — Not connected (per datasheet) |
| Pin 33 | VCC — 1.8V supply |
| Pin 34 | GND — Ground |
| Pin 35 | NC — Not connected (per datasheet) |
| Pin 36 | NC — Not connected (per datasheet) |
| Pin 37 | NC — Not connected (per datasheet) |
| Pin 38 | NC — Not connected (per datasheet) |
| Pin 39 | NC — Not connected (per datasheet) |
| Pin 40 | NC — Not connected (per datasheet) |
| Pin 41 | VCC — 1.8V supply |
| Pin 42 | GND — Ground |
| Pin 43 | NC — Not connected (per datasheet) |
| Pin 44 | NC — Not connected (per datasheet) |
| Pin 45 | NC — Not connected (per datasheet) |
| Pin 46 | NC — Not connected (per datasheet) |
| Pin 47 | NC — Not connected (per datasheet) |
| Pin 48 | NC — Not connected (per datasheet) |
Typische Anwendungen
XCF16PVO48C0973 ist geeignet für 6 Anwendungs: Spartan-3/3E FPGA Boot Storage, Spartan-6 Configuration Backup, Virtex-4/Virtex-5 High-Reliability Boot, CoolRunner-II CPLD Companion Storage, Industrial Controller FPGA Subsystems, Remote Field-Upgradeable Embedded Systems.
Spartan-3/3E FPGA Boot Storage
The XCF16PVO48C0973 is the canonical configuration storage device for Spartan-3 and Spartan-3E FPGA designs that require Master Serial boot. With 16-Mbit density it covers full bitstreams for XC3S50 through XC3S1500 devices with margin for design revisions. The 1.8V supply aligns directly to the Spartan-3 VCCO_2 bank, eliminating level shifters. Designers wire CCK, DIN, DOUT, and DONE through the FPGA's configuration pins, and the PROM autonomously streams the bitstream at power-up. In-system programmability over JTAG lets field upgrades proceed without removing the board.
Empfohlen
Spartan-6 Configuration Backup
For Spartan-6 designs, the XCF16PVO48C0973 serves as a fallback configuration PROM when SPI flash is not desired or when the design needs proven Xilinx validation. Spartan-6 natively supports both SPI flash and Master Serial PROM boot, and the XCF16P fits 16-Mbit bitstreams for the LX4 through LX150 tiers. Industrial control and factory automation equipment frequently pairs Spartan-6 with the XCF16P for long-term supply stability and a 10+ year product lifecycle, since both parts are mature, well-stocked, and supported by ISE design tools.
Empfohlen
Virtex-4/Virtex-5 High-Reliability Boot
The XCF16PVO48C0973 stores bitstreams for Virtex-4 LX/SX/FX and Virtex-5 LX/SX/ TXT/TXT platforms where high reliability and radiation tolerance are required. Aerospace and defense programs specify the XCF16P because of its proven field history and stable silicon. The PROM's CRC check during load matches the Virtex-4/5 configuration controller, ensuring bitstream integrity is verified before the FPGA enters user mode. In-system programmability allows secure field updates via JTAG.
Empfohlen
CoolRunner-II CPLD Companion Storage
CoolRunner-II CPLDs such as the XC2C256 or XC2C512 can operate as standalone devices or be paired with small FPGAs in mixed logic designs. The XCF16PVO48C0973 provides configuration storage for the FPGA portion of such designs while the CoolRunner-II handles housekeeping logic. This split architecture is common in industrial motor control, where the CPLD manages PWM and fault detection deterministically, and the FPGA performs signal processing. The PROM keeps the FPGA boot autonomous.
Empfohlen
Industrial Controller FPGA Subsystems
Programmable Logic Controllers (PLCs) and distributed I/O nodes often embed a Spartan-3E or Spartan-6 FPGA alongside a microcontroller, and the XCF16PVO48C0973 stores the FPGA image so that the FPGA can wake up autonomously without firmware coordination. This split reduces microcontroller boot time and allows the FPGA to handle deterministic real-time I/O from power-on. Industrial temperature rating (-40 C to +85 C) and long-term Xilinx supply commitments make the XCF16P a preferred solution for factory automation.
Empfohlen
Remote Field-Upgradeable Embedded Systems
Remote oil-and-gas monitoring stations, telecom infrastructure, and unattended sensor platforms rely on the XCF16PVO48C0973 for in-the-field firmware updates via JTAG. Engineers can rewrite the PROM image using Xilinx iMPACT or a JTAG programmer connected to a service laptop, without removing the board from the field. The 16-Mbit capacity accommodates several revisions of the FPGA bitstream, and the 48-TSOP industrial package withstands temperature and vibration in harsh enclosures.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für XCF16PVO48C0973 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | XCF16PVOG48C | XCF08PVOG48C | XCF32PVOG48C | XC18V04PC44C |
|---|---|---|---|---|---|
| Package | 48-TSOP (TFSOP, 0.724 inch / 18.40 mm) | 48-TSOP (same) | 48-TSOP (same) | 48-TSOP (same) | PLCC-44 (different footprint) |
| Brand | AMD Xilinx | AMD Xilinx (same) | AMD Xilinx (same) | AMD Xilinx (same) | Xilinx (same) |
| Memory Size | 16 Mb | 16 Mb (same) | 8 Mb (-50%) | 32 Mb (+100%) | 4 Mb (-75%) |
| Supply Voltage | 1.65 V to 2.0 V | 1.65 V to 2.0 V (same) | 1.65 V to 2.0 V (same) | 1.65 V to 2.0 V (same) | 3.0 V to 3.6 V (different) |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C (same) | -40 C to +85 C (same) | -40 C to +85 C (same) | -40 C to +85 C (same) |
| Programmable Type | In System Programmable | In System Programmable (same) | In System Programmable (same) | In System Programmable (same) | In System Programmable (same) |
| Configuration Interface | Serial (Master Serial / JTAG) | Serial / JTAG (same) | Serial / JTAG (same) | Serial / JTAG (same) | Serial / JTAG (same) |
| Compatible FPGA Families | Spartan-3/3E/6, Virtex-4/5, CoolRunner-II | Same families (identical) | Same families (identical) | Same families (identical) | Legacy Virtex/EPLD (limited) |
| Approximate Unit Price (qty 1) | $14.26 | $13 to $15 (similar) | $9 to $11 (lower) | $22 to $26 (higher) | $8 to $12 (lower, obsolete) |
Wichtigste Unterscheidungsmerkmale
- Larger bitstream capacity than XCF08P family (vs. XCF08PVOG48C)
- Smaller form factor and lower cost than XCF32P (vs. XCF32PVOG48C)
- Mature AMD Xilinx supply chain vs legacy Xilinx PLCC parts (vs. XC18V04PC44C)
Designhinweise
The XCF16PVO48C0973 draws its 1.8V supply from the FPGA's configuration bank. Place a 0.1 uF ceramic decoupling capacitor within 5 mm of each VCC pin and a 10 uF bulk tantalum or ceramic on the 1.8V rail. During CCK-burst reads the PROM current spikes can reach tens of mA; an undersized bulk capacitor will cause VCC droop that corrupts bitstream loading.
Route CCK and DOUT traces as a 50 ohm microstrip with ground reference, length-matched to within 25 mm of the FPGA's configuration clock input. Keep JTAG signals (TDI, TDO, TMS, TCK) clear of switching power sections to avoid programming failures. Use a TSOP-48 land pattern with 0.5 mm pitch and ensure the package orientation dot matches the schematic pin 1 marker.
Do not cascade the XCF16PVO48C0973 with non-Xilinx SPI flash; the opcode sets and timing differ. Verify that the bitstream size does not exceed 16 Mbit or the PROM will overflow and the FPGA will fail to enter user mode. When migrating to the XCF32P, double-check that the FPGA's configuration controller accepts a 32-Mbit image - some older Spartan-3 builds require a PROM-density compile setting.
Compliance-Informationen
RoHS, REACH, lead-free, and halogen-free status not explicitly stated in the verified distributor data; consult the manufacturer datasheet or contact Xilinx compliance for confirmed values.
