Módulos RF
Productos (294)
LM808 - 433 Mbps Wi-Fi 5 USB Adapter | LM Technologies
The LM Technologies LM808 is a 433.3 Mbps Wi-Fi 5 (802.11ac) USB 2.0 wireless client adapter designed for users requiring high-performance wireless connectivity on desktop and embedded hosts. Built around a Realtek 1T1R (one transmit, one receive) radio chipset, the LM808 fully supports all 802.11 bands including IEEE 802.11ac Draft 2.0 and the legacy 802.11 a/b/g/n specifications, while remaining backward compatible on 802.11n networks. Housed in a compact USB dongle form factor, the LM808 exposes the full 433 Mbps physical-layer rate available on a single spatial stream under 802.11ac, and is paired with a USB 2.0 device interface that draws bus power directly from the host. A Wi-Fi USB adapter is a peripheral module that bridges a host computer's USB bus to a wireless local area network (WLAN). The adapter's internal radio and baseband translate 802.11ac/a/b/g/n OFDM frames into USB packets, allowing any operating system with a generic WLAN driver stack to treat the device as a virtual Ethernet port. Within the wireless-networking taxonomy, the LM808 sits below embedded SiP modules and above raw chip-down radio designs, giving product developers a pre-certified, drop-in connectivity solution without needing to manage antenna matching or RF regulatory compliance themselves. Key features include dual-band 2.4 GHz and 5 GHz operation, Wi-Fi Direct peer-to-peer support for ad-hoc PAN-style networking, 1T1R MIMO, and full USB 2.0 high-speed bus compatibility. The adapter relies on OFDM modulation across the supported 802.11 bands and uses the host's WLAN driver stack to negotiate rates up to 433.3 Mbps. The Realtek-based design has been validated across Windows, Linux, and macOS reference stacks supplied by LM Technologies, removing the need for proprietary driver development. Typical applications include upgrading legacy desktop PCs to dual-band Wi-Fi 5, adding wireless connectivity to industrial PCs and point-of-sale terminals, embedded Linux gateways, retro gaming consoles, and digital signage players. The compact USB-A dongle footprint also makes the LM808 a convenient wireless client for developer boards that lack an on-board Wi-Fi radio, where it can be paired with a Linux host running NetworkManager or wpa_supplicant. When designing with the LM808, verify host-side driver availability for the target operating system and confirm the antenna's radiation pattern is appropriate for the enclosure. USB 2.0 bus-power limits must be observed when designing hubs that will host multiple LM808 adapters in parallel. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing engineers with a single reference for evaluating the LM808 against competing USB Wi-Fi 5 adapters.
LM813 - WiFi 802.11ac + BT 4.2 Combi Module | LM Technologies
The LM Technologies LM813 is a combination WiFi 802.11ac/a/b/g/n plus dual-mode Bluetooth v2.1/v3.0/v4.2 module delivered as a surface-mount device with an IPEX antenna connector. The module supports WiFi data rates to 433 Mbps and Bluetooth EDR to 2 Mbps (HS mode to 3 Mbps), exposing USB plus GPIO terminals for coexistence signaling in a single compact RF module footprint. A WiFi + Bluetooth combo module is a System-in-Package (SiP) or module-level integration of two radio subsystems (WiFi IEEE 802.11 family and Bluetooth) on a shared PCB, allowing a host processor to add wireless connectivity without designing RF matching networks or managing complex coexistence arbitration in firmware. Combo modules fall within the broader category of RF modules > wireless modules in the connectivity hierarchy. They are commonly deployed when BOM simplification, certified radio performance, and reduced time-to-market outweigh the need for lowest unit cost at scale. Key features of the LM813 include dual-band 2.4 GHz and 5 GHz WiFi operation under the IEEE 802.11ac/a/b/g/n standard family, dual-mode Bluetooth (Classic BR/EDR plus Bluetooth 4.2 LE) for backwards compatibility with legacy audio and data accessories, and an integrated coexistence interface exposed through GPIO pins for arbitration with co-located radios. The module carries an external IPEX/MHF antenna receptacle, allowing antenna selection to be tuned for the end application. The LM813 is built around a combination chipset that implements the 802.11ac MAC/PHY and Bluetooth baseband on a single die. WiFi throughput of 433 Mbps is delivered over a single spatial stream (1x1 SISO) using 802.11ac's mandatory MCS9 modulation, while Bluetooth uses an EDR-capable radio supporting 2 Mbps (HS mode 3 Mbps). The architecture offloads coexistence, channel access, and link-layer management from the host, leaving the host application processor responsible for higher-level networking (TCP/IP, BLE GATT services). Typical applications for the LM813 include industrial IoT edge gateways that need both WiFi infrastructure connectivity and Bluetooth for local provisioning or sensor beacons, point-of-sale (POS) terminals that accept Bluetooth card readers or barcode scanners while joining the store WiFi, and embedded HMI panels requiring over-the-air firmware updates. The dual-band capability also suits consumer audio docks that stream WiFi while maintaining a Bluetooth fallback path. When designing with the LM813, engineers should review the host interface (USB) pin mapping and supply the module from a clean 3.3 V rail with adequate decoupling. Antenna placement and ground keep-out around the IPEX feed line directly affect radiated performance and regulatory compliance. This page synthesizes distributor references, host-interface guidance, and verified parametric data not consolidated in the LM Technologies datasheet.
LM816 - 150Mbps WiFi 4 USB Nano Adapter | LM Technologies
The LM Technologies LM816 is a WiFi 4 (802.11 b/g/n) USB Nano wireless adapter delivering up to 150 Mbps PHY rate, built around a Realtek RTL8188EUS chipset and housed in a compact USB-A dongle form factor. Designed for low-power 5V operation via the USB bus, it supports both ad-hoc and infrastructure mode network architectures and is fully compliant with IEEE 802.11n, b, g, e and i standards including 802.11e QoS and 802.11i security extensions. The integrated chip antenna (IC-ANT) keeps the BOM minimal, making the LM816 well suited to space-constrained host platforms such as single-board computers, industrial gateways, and embedded Linux/Windows devices. A Wi-Fi 4 (802.11n) USB adapter is a peripheral that converts a wired USB host port into a wireless network client operating in the 2.4 GHz ISM band, providing 1x1 SISO throughput up to 150 Mbps and supporting legacy 802.11b/g fallback. In the broader hierarchy, the LM816 sits under wireless LAN adapters -> networking peripherals -> computer interfaces, and uses a single spatial stream with 20 MHz channels and 40 MHz HT capability. This product class is widely adopted for legacy Wi-Fi connectivity on embedded systems where cost, footprint, and driver maturity matter more than the multi-gigabit throughput of newer Wi-Fi 6/6E modules. Key features include hardware-based 64/128-bit WEP, WPA, and WPA2 encryption, soft-AP / Wi-Fi Direct capability, and driver support for Windows, Linux, and macOS hosts. The adapter enumerates as a USB 2.0 high-speed device and uses the standard RTL8188EUS driver tree maintained by Realtek and the Linux community. An internal printed chip antenna (AO/IC-ANT) eliminates the need for an external antenna while preserving the link budget required for typical indoor ranges. The LM816 references the Realtek RTL8188EUS single-chip 802.11n controller, which integrates the MAC, baseband, RF transceiver, and PA on a single die, requiring only an external crystal, EEPROM, and antenna matching network. The 1T1R radio chain, combined with Short GI and MCS7 modulation, enables the headline 150 Mbps PHY rate while staying within USB 2.0 bus bandwidth. This architecture explains the module's low power consumption and small footprint compared to discrete solutions. Typical applications include retrocomputing and embedded Linux SBCs (Raspberry Pi, Toradex, BeagleBone), industrial HMI terminals, point-of-sale systems, digital signage media players, and low-cost retrofit wireless upgrades for older desktops or laptops. The LM816 is also used as a quick evaluation reference for engineers validating 2.4 GHz Wi-Fi link behavior in prototype designs. When integrating the LM816, ensure the host platform provides a USB 2.0 high-speed port with sufficient bus power (typically 500 mA @ 5V). RF performance is sensitive to USB cable length and chassis shielding; for chassis-mounted applications, route the dongle externally to avoid degrading antenna patterns. Verified driver compatibility with the host OS should be confirmed before deployment in production. This page synthesizes distributor pricing, drop-in adapter alternatives, and application notes not found in the manufacturer datasheet, helping engineers select the right Wi-Fi adapter for embedded and industrial deployments.
LM816-USB - 150Mbps Wi-Fi 4 USB Nano Adapter | LM Technologies
The LM Technologies LM816-USB is a Wi-Fi 4 (802.11b/g/n) USB Nano Adapter that delivers up to 150 Mbps data transfer in a compact USB dongle form factor. It is built around a Realtek 8188EUS chipset and is fully compliant with IEEE 802.11 b, g, and n standards, including 802.11e and 802.11i features. The adapter operates in the 2.4 GHz ISM band and supports both ad-hoc and infrastructure network architectures. A USB Wi-Fi adapter (also called a WLAN dongle) is a peripheral that adds wireless networking capability to a host device via the USB bus. It encapsulates the radio, baseband, MAC, and host interface into a self-contained module, allowing embedded systems, single-board computers, and PCs to join Wi-Fi networks without integrating a chipset directly on the motherboard. Within the wireless connectivity hierarchy, USB Wi-Fi adapters sit alongside PCIe Wi-Fi cards, SDIO Wi-Fi modules, and solder-down M.2 WLAN cards as one of the easiest ways to add Wi-Fi to a design. Key features of the LM816-USB include a 1T1R (single transmit / single receive) radio chain, 20 MHz channel bandwidth, and 64/128-bit WEP, WPA, and WPA2 encryption. The adapter is powered directly from the USB 5 V rail, eliminating the need for an external power supply. A reference designator on the product page identifies it as "ADT, 802.11n, USB, 150Mbps, 5V Realtek 8188EUS, Nano". The adapter is pre-certified, which shortens time-to-market for OEMs that would otherwise need to certify a discrete radio. The LM816-USB uses a Realtek RTL8188EUS single-chip 802.11n controller, which integrates the 2.4 GHz radio, MAC, and baseband. The dongle presents a USB 2.0 device to the host and exposes a Wi-Fi station through the standard WLAN NDIS / nl80211 interface on Linux or the Wi-Fi NDIS miniport on Windows. This chipset family is broadly supported by mainline Linux kernels, simplifying driver integration on embedded Linux hosts (note: Toradex lists the LM816 as HCI for Windows CE; embedded Linux support depends on the kernel version in use). Typical applications include adding Wi-Fi to Raspberry Pi or other SBC projects, industrial control panels requiring wireless network access, point-of-sale terminals needing network connectivity, retro computing projects that need network access on legacy hardware, and embedded Linux development boards that lack an on-board Wi-Fi chipset. Its 150 Mbps link rate is sufficient for typical browser, email, and IoT telemetry workloads. When designing with this adapter, consider that the USB connector orientation and dongle clearance must be planned at the chassis level. Because the radio radiates through the dongle body, the USB port should be positioned away from large metal structures that attenuate 2.4 GHz signals. For best throughput, place the host within line-of-sight of the access point and avoid operating near 2.4 GHz interference sources such as microwave ovens and Bluetooth peripherals. This page synthesizes distributor inventory, datasheet specifications, chipset architecture, and application guidance for the LM816-USB, providing practical engineering context beyond what the manufacturer datasheet alone offers.
LM822 - 802.11 b/g/n WiFi Module with IC Antenna, USB HCI | LM Technologies
The LM Technologies LM822 is a WiFi 802.11 b/g/n module operating in the 2.4 GHz ISM band with an onboard chip (IC) antenna and a USB Host Controller Interface (HCI). It supports the IEEE 802.11b, 802.11g and 802.11n standards and delivers data rates up to 150 Mbps on a single stream, packaged as a plug-and-play USB module for OEM integration. What is a WiFi 802.11n (WiFi 4) module? A WiFi 4 (802.11n) module is an embedded radio subsystem that implements the IEEE 802.11n physical and MAC layers and exposes either a host-controlled (HCI) or full-stack (network) interface to the host processor. The LM822 specifically implements HCI over USB, meaning the host CPU runs the network stack and the module acts as a 2.4 GHz radio front-end. These modules sit in the wireless connectivity layer of an embedded system, above the physical RF transceiver and below the application networking stack, and are widely used to retrofit wireless capability into industrial PCs, single-board computers, point-of-sale terminals and gateways. Key specifications of the LM822 per the LM Technologies datasheet include a 150 Mbps PHY rate, BPSK/QPSK/16-QAM/64-QAM modulation, WEP/TKIP/AES plus WPA/WPA2 encryption, a built-in IC antenna (no external antenna or RF connector required), and Linux/macOS/Windows 10 IoT Core/Windows XP to Windows 10/Windows Compact Embedded 6/7 driver support. Compliance with 802.11e bursting and 802.11I standards is also listed. The module draws 5 V through the USB bus and uses the USB port as both the data interface and the power rail. Because all protocol stacks are offloaded onto the host OS (it is HCI-only), the LM822 needs no additional firmware flashing for typical OS environments - it enumerates as a USB WiFi adapter. This makes it well suited to industrial PCs and SBCs that need to add wireless connectivity without a custom driver port. Typical applications include retrofitting WiFi onto legacy industrial PCs, adding wireless connectivity to single-board computers in kiosk and POS designs, embedded gateways that bridge Ethernet to 802.11n WiFi, and Windows Compact Embedded terminals. In each case the LM822's USB HCI and plug-and-play OS driver coverage reduce integration effort compared with bare 802.11 ICs. When designing with this module, note that 2.4 GHz operation only means the host system must coexist with Bluetooth, microwave ovens, and other 2.4 GHz interferers common in industrial and consumer environments. Channel planning and adequate placement of the host PCB relative to metal enclosures is critical because the onboard IC antenna's radiation pattern is shaped by the surrounding ground plane. This page synthesises distributor pricing, a feature comparison with adjacent LM Technologies modules, and practical integration notes that go beyond what the manufacturer datasheet alone covers, helping engineers decide whether the LM822 is the right drop-in wireless module for their embedded platform.
LM823 - WiFi 802.11 b/g/n 150Mbps USB Module | LM Technologies
The LM823 is a WiFi 4 (802.11 b/g/n) USB module from LM Technologies delivering up to 150Mbps wireless throughput at 2.4 GHz with HCI host interface via USB. It is offered in SMT form factor with an IPEX receptacle (u.FL-compatible antenna connector) and operates from a single 3.3 V supply. The module is designed to provide excellent performance with low power consumption while supporting b/g/n standards with full 150 Mbps PHY rate. A WiFi module is a compact radio subsystem that integrates the RF transceiver, baseband processor, MAC, and host interface (USB, SDIO, SPI, or UART) into a single, certified or pre-certified hardware block. It allows a host processor or embedded MCU to add wireless connectivity without having to design the analog RF chain, antenna matching network, or regulatory radio from scratch. WiFi modules are classified by generation (WiFi 4 = 802.11n, WiFi 5 = 802.11ac, WiFi 6 = 802.11ax), by host interface (USB, SDIO, SPI, UART), and by antenna integration (chip antenna, trace antenna, or external antenna via u.FL/IPEX). Key features of the LM823 include IEEE 802.11 b/g/n compliance, 150 Mbps maximum PHY data rate on a 2.4 GHz single-band radio, USB 2.0 HCI host interface, integrated IPEX/u.FL antenna receptacle for flexible external antenna selection, low-power operation, and a compact SMT package for high-density PCB placement. It is shipped in trays of 40 pieces and supports Linux/Android/Windows host drivers commonly available for USB WiFi dongle-class silicon. The module integrates a 2.4 GHz single-band 1x1 SISO radio with 20 MHz channel bandwidth, supporting DSSS/CCK for 802.11b and OFDM for 802.11g/n. Internally it relies on a USB-attached WiFi SoC whose host drivers are widely packaged in mainline Linux kernels, Android, and Windows, so no proprietary firmware porting is required on common host platforms. The IPEX receptacle allows the integrator to swap a higher-gain external antenna for better link margin in metal-enclosed products. Typical applications include embedded Linux gateways, IoT edge nodes, industrial wireless telemetry, point-of-sale terminals, retrofit WiFi for set-top boxes and media players, and USB-attached wireless connectivity for SBCs and developer boards that lack built-in WiFi. The 150 Mbps PHY rate is sufficient for video streaming up to 1080p, VoIP, and bulk file transfer on a local network. When designing with this module, mount the antenna connector area clear of ground copper and tall components to avoid pattern distortion; route the USB D+/D- pair as a 90 ohm impedance-controlled differential pair with matched length. For regulatory compliance, the modular transmitter typically still requires antenna selection and host-integration testing against FCC/CE rules for the final product. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes for the LM823 that are not consolidated in the LM Technologies datasheet alone.
LM843 - WiFi 802.11ac + BT 5.0 2T2R USB Combo Module | LM Tech
The LM Technologies LM843 is a WiFi 802.11ac plus Bluetooth 5.0 dual-mode combination SMT/USB module in the LM843 series, providing 2-stream 802.11ac with Multi-User MIMO connectivity and integrated power management. Per the LM Technologies product page and datasheet, the module is offered in multiple SKUs covering tray/IPEX and 2x RF line-out antenna options, all sharing the same WiFi+BT 5.0 silicon foundation. A WiFi + Bluetooth combo module is a small surface-mount or USB assembly that packages a WiFi radio, a Bluetooth radio, an RF front-end, a crystal oscillator, and a host interface (USB, SDIO, or UART) into a single, pre-certified hardware block. This module category sits inside the broader taxonomy of RF modules -> RF transceivers -> wireless connectivity ICs -> semiconductors. By integrating both radios, the module reduces BOM, host-side firmware complexity, and time-to-market for devices that need simultaneous WiFi and Bluetooth coexistence. Key features of the LM843 include dual-band 2.4/5 GHz 802.11ac operation in a 2T2R MIMO configuration, Bluetooth 5.0 dual-mode support (Classic BR/EDR 2.1/3.0/3.0+HS and Low Energy 4.0/4.1/4.2/5.0) with multiple simultaneous Classic+LE connections, USB 2.0 host interface, and on-board power management for maximising throughput across coexisting WiFi/BT links. Hardware is BT 5.0 compliant at the silicon level. Architecturally, the LM843 series uses a 2x2 MIMO WiFi subsystem combined with a Bluetooth 5.0 dual-mode radio sharing a single module PCB and antenna chain through an internal coexistence interface. The USB 2.0 interface carries both WiFi and Bluetooth traffic to the host, simplifying driver bring-up versus SDIO+UART split designs. Typical applications include industrial IoT gateways, wireless POS terminals, set-top boxes and media streaming dongles, USB WiFi+BT adapters, in-vehicle infotainment companion radios, and embedded Linux/Windows host platforms requiring a pre-certified combo radio. Design tip: confirm the exact SKU variant - LM843-8432 (tray, 2x IPEX), LM843-8434 (USB, 2x IPEX), LM843-8438 (tray, 2x RF line-out) - matches the desired host interface (USB vs SMT) and antenna connector (IPEX MHF4 vs RF line-out pad) before PCB layout. This page synthesises verified distributor pricing, drop-in alternative notes, and application-level design guidance that are not consolidated in the LM Technologies datasheet alone.
LM845 - WiFi 802.11ac + Bluetooth 4.2 USB Nano Adapter | LM Technologies
The LM Technologies LM845 is a compact WiFi 5 (802.11ac) and Bluetooth 4.2 dual-mode USB nano adapter (dongle) built around a fully integrated single-chip Realtek radio. It operates on the 2.4 GHz and 5 GHz WiFi bands with 1-stream 802.11ac and Multi-user MIMO (MU-MIMO), and it supports Bluetooth v4.2 Dual Mode with backward compatibility to Bluetooth v2.1+EDR and v3.0. Classic Bluetooth and Bluetooth Low Energy (LE) can run simultaneously, enabling concurrent wireless audio/data and BLE beacon use cases over the same USB interface. A WiFi + Bluetooth USB combo dongle is a peripheral that adds short-range wireless connectivity to a host PC, embedded board, or industrial appliance via the USB bus. Inside the dongle, a single radio SoC handles both WiFi (the 802.11 family) and Bluetooth (BR/EDR/LE), sharing one antenna chain through an internal RF front-end. The host sees two logical interfaces (a network interface for WiFi and an HCI interface for Bluetooth) over USB, which simplifies driver integration and shrinks the dongle to a nano form factor that can be left plugged into a laptop or set-top box. Key features of the LM845 include 1-stream 802.11ac Wave-2 operation with MU-MIMO, dual-band 2.4/5 GHz support, Bluetooth 4.2 Dual Mode (BR/EDR + LE) with simultaneous Classic + LE links, a USB 2.0 high-speed host interface, and a Realtek-based single-chip radio that minimizes BOM and power draw. The dongle form factor is sized for always-on installation in laptops, mini-PCs, and industrial HMIs. The internal architecture relies on a Realtek combo MAC/baseband IC with an integrated 2.4/5 GHz PA/LNA chain. WiFi throughput reaches 433 Mbps on the 5 GHz 802.11ac 1x1 link, while Bluetooth supports the standard BR/EDR profiles plus BLE GATT services for IoT pairing and beaconing. Because WiFi and Bluetooth share the same RF chain, the firmware coordinates time-division scheduling to avoid mutual interference. Typical applications include adding dual-band WiFi 5 + Bluetooth to legacy desktop or embedded systems, IoT gateways and industrial PCs that need a quick wireless drop-in upgrade, point-of-sale terminals that pair with BLE peripherals, retrofitted media PCs and set-top boxes that need 5 GHz WiFi for HD streaming, and developer/test rigs that require a stable Realtek-based combo radio for driver qualification. When designing with the LM845, remember that it is a finished USB dongle, not a bare IC: designers cannot change the antenna, regulators, or USB stack. Host drivers must support the underlying Realtek chipset for full 802.11ac + Bluetooth 4.2 functionality, and the host OS USB port must provide enough bus power for the 5 GHz PA under load. This page synthesizes verified distributor information, parametric specifications, and design guidance not consolidated on any single manufacturer or distributor page, including practical notes on host-driver compatibility and concurrent WiFi + Bluetooth operation.
LM848 - Wi-Fi 6 (802.11ax) and Bluetooth 5.2 USB Combo Adapter | LM Technologies
The LM Technologies LM848 is a USB 3.0 combo adapter that integrates Wi-Fi 6 (802.11ax) and Bluetooth 5.2 connectivity through a single USB Host Controller Interface (HCI) port. Designed for embedded Linux, Windows, and Android hosts, the LM848 exposes a high-throughput wireless pipe without burdening the host CPU with baseband firmware, because the dual-mode radio runs the 802.11ax MAC/PHY and the BT 5.2 controller silicon on-module. The USB 3.0 uplink provides the bandwidth required for 2x2 MU-MIMO, 160 MHz channel operation, and OFDMA scheduling features defined in the 802.11ax amendment. A USB combo adapter is a peripheral that bridges a host processor to two or more wireless radios through a standardized serial bus. In the wider connectivity taxonomy, this places the LM848 as a USB peripheral module -> wireless network adapter -> combo radio module -> RF subsystem, sitting beneath the host's network stack and above the antenna. USB-based combo adapters are favored over SDIO or PCIe cards in industrial and prototyping environments because they avoid slot allocation, simplify thermal management, and survive hot-swap events without rebooting the host. The headline features of the LM848 include 802.11ax 2x2 operation, WPA3 security compliance, dual-band 2.4 GHz / 5 GHz / 6 GHz coverage where supported by regional regulations, Bluetooth 5.2 with LE Audio and Long Range (PHY Coded), and a USB 3.0 Type-A form factor that draws bus power. The device advertises ultra-fast throughput that suits video streaming, edge AI gateways, and dense Wi-Fi deployments where 802.11ac throughput would saturate. Architecturally, the LM848 pairs an 802.11ax SoC with a BT 5.2 companion chip, sharing a single USB endpoint group over a USB 3.0 SuperSpeed link. The radio front end is tuned for worldwide regulatory domains, and the firmware exposes standard nl80211/cfg80201 (Linux) and MediaTek/Realtek-style vendor extensions (Windows) for throughput tuning. Typical applications include industrial IoT gateways, in-vehicle infotainment prototyping, point-of-sale terminals, medical telemetry docks, and digital signage where Wi-Fi 6 capacity and Bluetooth coexistence are both required. When designing with the LM848, ensure the host supplies a USB 3.0 port capable of delivering 900 mA, and place the antenna at least 20 mm from any metal enclosure walls to preserve EIRP margin.
LM849 - Wi-Fi 6/BT 5.2 2T2R USB Combo Module | LM Technologies
The LM Technologies LM849 is a dual-band Wi-Fi 6 (IEEE 802.11ax) plus Bluetooth 5.2 combo embedded module in a USB form factor that delivers 2T2R MIMO wireless connectivity for OEM, industrial, medical, scientific, and commercial applications. The module integrates a high-speed host interface compliant with the USB 3.0 specification and remains fully backward compatible with USB 2.0 hosts, supporting 2.4 GHz and 5 GHz simultaneous operation. It is shipped with dual factory antenna configurations supporting either on-board IPEX micro-coaxial connectors or SMT RF line-out pads to suit different mechanical layouts. A Wi-Fi module (also called a wireless module or RF module) is a pre-certified subsystem that integrates a radio transceiver, baseband processor, RF front-end, and host interface on a single PCB, enabling product designers to add wireless connectivity without writing a full driver stack or performing radio compliance testing from scratch. Wi-Fi modules sit at the bottom of the connectivity hierarchy: RF transceiver -> Wi-Fi/BT module -> wireless SoC -> semiconductor, and they are classified by radio technology (Wi-Fi 6 / 802.11ax), host interface (USB / SDIO / PCIe), and supported bands (2.4 GHz / 5 GHz / 6 GHz). Key features of the LM849 include 2x2 MU-MIMO on 802.11ax with up to 1200 Mbps physical layer rate, Bluetooth 5.2 dual-mode (BR/EDR/LE) support, USB 3.0 SuperSpeed host interface, integrated RF shielding, and an industrial operating temperature range suitable for OEM embedded designs. The module is pre-certified in many jurisdictions, which removes a major certification barrier for low-to-medium volume product launches. Typical applications include industrial IoT gateways, point-of-sale terminals, medical telemetry dongles, scientific instrumentation, and commercial wireless display adapters where a USB-attached radio is more practical than an M.2 card. The 2T2R configuration also benefits video streaming and VoIP endpoints that benefit from transmit beamforming and dual-stream receive diversity. When designing with the LM849, confirm the host platform provides sufficient USB 3.0 bus power during radio transmit peaks (typical peak current ~900 mA) and that the chassis antenna path meets the 50 ohm controlled-impedance requirement of either the IPEX connector variant or the SMT RF pad variant.
LM961 - Bluetooth 5.0 Dual Mode Module | LM Technologies
The LM Technologies LM961 is a Bluetooth 5.0 Dual Mode module that combines a Bluetooth Low Energy radio and a Bluetooth v2.0/v2.1 classic radio on a single core with an integrated microcontroller and 8 Mbit flash memory. According to the LM Technologies LM961 datasheet, this module operates as either a GAP Central (master) or GAP Peripheral (slave) device and supports streaming high-quality data while maintaining backward compatibility with Bluetooth v2.0, v2.1, v4.0, v4.1, and v5.0 peers, including iOS and Android hosts. The module is targeted at embedded designs that need a standalone, AT-command-configurable wireless link without requiring an external host MCU to manage the stack. A Bluetooth module is a self-contained subsystem that integrates the radio transceiver, baseband controller, host interface, and sometimes an on-board MCU plus an antenna matching network, exposing a simplified UART/SPI/USB control surface to the host processor. In the broader taxonomy, the LM961 sits within RF modules, which fall under RF & Wireless components, sitting alongside bare RF transceivers, RF amplifiers, and integrated SoCs. Dual mode specifically means the silicon can speak both Classic Bluetooth (BR/EDR) and Bluetooth Low Energy under the same Bluetooth 5.0 stack, which is critical for products that must interoperate with the installed base of classic-only peripherals while also taking advantage of BLE's low-power data channels. Key features include 3 Mbps maximum data rate (BLE 5.0 PHY), embedded Bluetooth dual mode stack, 8 Mbit on-module flash for user application code, and configuration via AT commands in configuration mode. The module supports GAP central and peripheral roles and can establish Bluetooth Low Energy connections in addition to classic SPP/ACL streams. It is designed as a single-core standalone module, meaning the host MCU and the Bluetooth controller share processing on the same die, simplifying hardware design. The architecture pairs an integrated MCU with the Bluetooth 5.0 dual mode core, freeing the application processor from running the Bluetooth stack. Power consumption is dominated by the radio duty cycle, so BLE connection intervals can be tuned for ultra-low average draw in battery-powered products. The 8 Mbit flash allows OEMs to embed application firmware and AT-command scripts directly on the module. Typical applications include industrial IoT gateways, health and fitness wearables, M2M telemetry, point-of-sale terminals, and cable replacement for serial-port legacy equipment. The module is also well-suited for streaming high-quality sensor data over SPP or BLE to iOS and Android tablets. When designing with this device, confirm that the antenna placement keeps the keep-out zone clear of ground pour and that the host PCB provides a clean 3.3 V rail, because TX current spikes directly modulate VCC and degrade RF performance. AT-command configuration requires the host UART to be set to the documented baud rate and flow-control mode. This page synthesizes distributor pricing, drop-in module alternatives from the LM Technologies family, and practical RF design notes not found on the manufacturer datasheet cover page.
LN940A9 - LTE Cat 9 M.2 Module 450 Mbps GNSS | Telit
The Telit LN940A9 is an LTE Category 9 M.2 data card module delivering up to 450 Mbps downlink and 50 Mbps uplink peak data rates, with global 3G fallback and an integrated GNSS receiver, housed in the industrial-grade M.2 form factor for mobile computing, networking, and industrial IoT platforms. An LTE Cat 9 module is a cellular wide-area-network transceiver that aggregates multiple LTE carriers (carrier aggregation, up to 3x20 MHz in Cat 9) to reach higher throughput than single-carrier Category 4 devices. Within the wireless connectivity hierarchy, it sits between entry-level Cat 4 modules and LTE-Advanced Pro (Cat 11 and above) devices, and belongs to the broader family of cellular modems, WWAN data cards, and M2M/IoT communication modules. Key features of the LN940A9 include LTE Category 9 capability for North America, Europe, and APAC, worldwide 3G fallback for coverage continuity, built-in GNSS for positioning, and a power-optimization enablement suite. According to the Telit LN94x series datasheet, the LN940 family supports Adaptive Clocking, Selective Suspend, Link Power Management, Dynamic Power Reduction, and Tunable Antenna features that together reduce power consumption in battery-powered devices. The LN940 family is optimized for low power consumption and a smaller, thinner footprint than older PCIe mini-card designs. The industrial-grade M.2 form factor allows easy integration into laptops, tablets, routers, gateways, and ruggedized industrial IoT devices. The M.2 interface carries USB 3.0 / PCIe connectivity, SIM, and GNSS signals over the standard M.2 edge connector, simplifying mechanical design and antenna placement. In practice, the module is used as the WWAN engine behind a host OS driver stack (Windows and Linux drivers are available per 4gltemall documentation listings). Typical applications include mobile computing WWAN cards (the LN940A9 is widely referenced as T77W676 in branded laptop builds), industrial IoT gateways and routers requiring resilient LTE-A backhaul, and networking equipment needing 450 Mbps downlink with 3G fallback. The integrated GNSS receiver supports asset tracking and location-aware services without a separate GPS module. Design consideration: as a cellular module, the LN940A9 requires careful RF layout - keep the M.2 antenna connectors matched to 50 ohm, follow the Telit hardware design guidelines for power sequencing, and budget for module thermal dissipation during sustained uplink transfers. This page synthesizes distributor pricing references, drop-in alternatives, application guidance, and design notes not found in the manufacturer datasheet alone, giving engineers a single citable reference for the Telit LN940A9.
LSM100A - Sub-GHz LoRa & Sigfox RF Module | Seong Ji
The Seong Ji LSM100A is a compact, low-power, bidirectional Sub-GHz radio module that supports both LoRa and Sigfox modulation technologies across the 863 MHz to 928 MHz frequency band. It is built around the STMicroelectronics STM32WL system-on-chip, integrating the radio transceiver and microcontroller in a single silicon die. The module measures 14.0 mm x 15.0 mm x 2.8 mm in an LCC-34 surface-mount package with half-through-hole castellated pads for reflow soldering and hand prototyping. A Sub-GHz RF module is a pre-certified, PCB-integrated radio block that combines a transceiver IC, matching network, crystal oscillator, and antenna interface into a single qualified assembly. The LSM100A belongs to the LPWAN (Low-Power Wide-Area Network) module family, sitting below complete SoC transceivers in the wireless connectivity taxonomy and above bare RFICs. It is offered in both AT-command firmware and API firmware variants, where the AT version exposes a serial command interface and the API version exposes the STM32WL firmware APIs for custom application code. Key features include Sigfox RC1 protocol support plus LoRaWAN connectivity simultaneously, ultra-low sleep current for battery-powered deployments, CE / LoRaWAN / Sigfox pre-certification, and an evaluation board (EVBLSM100A) for fast prototyping. The module uses spread-spectrum modulation to deliver ultra-long-range communication with high interference immunity while keeping average current consumption minimal, making it well aligned with metering, asset tracking, and remote sensor applications. The integrated STM32WL SoC provides an ARM Cortex-M4 application core alongside the Sub-GHz radio peripheral, eliminating the need for an external host MCU in many designs. AT-command firmware converts the module into a transparent UART-controlled modem, while the API variant lets integrators load their own firmware into the on-module MCU. This dual-mode capability makes the LSM100A suitable for both quick time-to-market deployments and deeply integrated products. Typical applications include Sigfox RC1 field devices, LoRaWAN end nodes for smart agriculture and utilities, wireless alarm and security sensors, industrial telemetry modems, smart city infrastructure, and battery-powered IoT sensor clusters. The pre-certified RF section removes the most time-consuming compliance step for low-volume product teams. When designing with the LSM100A, ensure the host PCB provides a 50 ohm RF feed to the module antenna pad and adequate clearance under the antenna keep-out area to preserve the radiated performance verified during certification.
LSM110A - LoRa & Sigfox 902-928MHz Hybrid Module | SJIT
The Seong Ji (SJIT) LSM110A is a compact, low-power, bidirectional radio transceiver module for the 902 MHz to 928 MHz sub-1 GHz ISM band, integrating Semtech LoRa and Sigfox modulation technologies in a single FCC-certified LCC-34 package measuring 14.0 mm x 15.0 mm x 2.8 mm. The module delivers up to +22 dBm output power and supports Sigfox RC2/RC4 zones together with LoRaWAN on US902-928, AU915-928, and AS923-1 regional profiles, enabling hybrid LPWAN connectivity for global IoT deployments. It is built around an STM32WL series sub-1 GHz SoC, which combines an Arm Cortex-M4 microcontroller with an integrated LoRa radio, eliminating the need for an external MCU in many designs. The module is supplied in both AT-command and API firmware variants, with the API version allowing customer firmware to be integrated directly inside the module. A half-through-hole land pattern allows the LSM110A to be soldered like a standard SMD component onto a simple two-layer carrier board with only a few external passives required. The LSM110A is pre-certified under FCC ID 2BEK7LSM110A, which reduces compliance cost and time-to-market for end products intended for the Americas and Australia. A LoRa (Long Range) radio module is a wireless transceiver sub-system built on Semtech's chirp-spread-spectrum modulation that delivers kilometer-scale communication at very low current consumption, ideal for battery-powered IoT endpoints. Sigfox is a complementary ultra-narrowband LPWAN technology operated by a global network carrier that uses the same sub-1 GHz ISM bands but provides lower bit-rate, longer-range, ultra-low-power messaging. By integrating both protocols, hybrid modules such as the LSM110A let designers choose the optimal transport per packet, geographic region, or application without redesigning hardware. Key features include a high-interference-immunity spread-spectrum physical layer, support for AT and API command interfaces, and FCC pre-certification. The 14.0 x 15.0 mm LCC-34 footprint makes it the smallest LoRa+Sigfox hybrid module in the SJIT portfolio and one of the smallest on the market, allowing product miniaturization for asset trackers and wearable sensor nodes. Architecturally, the STM32WL SoC integrates the radio, modem, and microcontroller into one die, reducing BOM count and PCB area. The LCC-34 package's exposed ground pad improves thermal performance and RF grounding for consistent radiated performance across production lots. Typical applications include Sigfox/LoRaWAN asset tracking, smart agriculture soil and livestock sensors, smart-metering endpoints, industrial SCADA monitoring, and GPS-free indoor/outdoor positioning reference nodes. The hybrid protocol support means a single SKU can ship to the US, Australia, and parts of Asia with no firmware region-locking. When designing with the LSM110A, ensure the antenna matching network is tuned for the specific antenna chosen (chip, trace, or external SMA) and that the host MCU's UART levels match the module's 3.3 V CMOS interface. Power-rail decoupling requires at least a 10 uF bulk plus a 100 nF ceramic placed within 5 mm of the module's VDD pins. This page consolidates distributor pricing, drop-in alternatives from the SJIT LSM family, and practical design notes that are not collated in any single manufacturer datasheet.
LTP5900IPC-WHMA#PBF - SmartMesh WirelessHART Mote 2.4GHz | ADI
The Analog Devices LTP5900IPC-WHMA#PBF is a 22-pin SmartMesh WirelessHART mote module operating in the 2.4 GHz ISM band as part of the Eterna family of IEEE 802.15.4 printed-circuit-board assembly solutions. The module integrates an ARM Cortex-M3 32-bit microprocessor with Dust Networks embedded SmartMesh WirelessHART networking software, an on-board 2.4 GHz radio, and an MMCX antenna connector supporting up to 8 dBm TX power at 250 kbps over 16 channels centered at 2483.5 MHz. The through-hole module is shipped in a tray and is qualified for industrial temperature operation from -40 °C to +85 °C, providing a forward-compatible upgrade path for designers using the legacy M2510 PCB module. A WirelessHART mote is a self-managing, low-power radio node used to build self-forming, self-healing mesh networks for process automation. Within the broader taxonomy, the LTP5900-WHM sits at the intersection of an IEEE 802.15.4 transceiver SoC (system-on-chip), an embedded wireless MCU module, and an industrial-grade sensor-networking appliance. Compared with proprietary RF modules, WirelessHART layers standard IEC 62591 channel hopping and time-synchronized mesh scheduling on top of IEEE 802.15.4e, giving deterministic latency, AES-128 encryption, and full interoperability with any HART host system. Key technical features include 16 selectable 2.4 GHz channels, a transmit output power up to 8 dBm with receiver sensitivity of -95 dBm (typical), an integrated ARM Cortex-M3 core running SmartMesh WirelessHART network stack, secure AES-128 link-layer encryption, and over-the-air firmware upgrade capability. The module carries FCC, IC, ETSI, Telec, and ARIB radio certifications, eliminating the customer's own RF compliance burden for global deployments. Time-synchronized channel hopping provides deterministic latency and sub-millisecond time synchronization across the mesh. Typical applications include wireless process monitoring in petrochemical and oil-and-gas plants, wireless temperature, pressure, and flow sensor nodes, condition monitoring on rotating equipment, environmental monitoring, and any brownfield HART instrumentation installation where running new cable is impractical. The module's ultra-low-power duty-cycled radio and embedded mesh stack allow battery-powered motes to run for years on primary cells. Design considerations when using the LTP5900IPC-WHMA#PBF include providing a regulated 2.1 V to 3.6 V DC supply, routing the MMCX antenna trace correctly, observing the host-board keep-out area under and around the on-board chip antenna path, and following the reference schematic in the manufacturer datasheet. Antenna selection, matching network, and enclosure material strongly influence RF range and must be evaluated against the SmartMesh Power and Performance Estimator tool before final qualification. This page synthesizes distributor pricing for the 22-pin WHM-A variant, drop-in comparison against related SmartMesh modules (LTP5901-WHM with chip antenna, LTP5902-WHM with MMCX connector), and practical design notes for industrial WirelessHART deployment not consolidated in any single distributor listing.
LTP5902IPC-WHMA#PBF - 802.15.4 WirelessHART Mote Module | ADI
The Analog Devices LTP5902IPC-WHMA#PBF is a SmartMesh WirelessHART mote-on-board RF transceiver module in the Eterna family of IEEE 802.15.4 printed circuit board assembly solutions. It operates in the 2.4 GHz ISM band, delivers 8 dBm maximum RF output power, and supports an over-the-air data rate of 250 kbps. The module ships in surface-mount PCB form with an MMCX antenna connector (antenna not included). A wireless mote module is a self-contained sub-system that combines a radio transceiver, microcontroller, and qualified protocol stack on a single PCB so that designers can add mesh networking to a sensor node without writing low-level radio firmware. Within the broader SmartMesh hierarchy, the LTP5902 sits inside Dust Networks' WirelessHART / 6LoWPAN product tree, which itself belongs to the 802.15.4 family of low-rate wireless personal area network (LR-WPAN) standards. SmartMesh WirelessHART networks are self-managing, ultra-low-power mesh networks optimized for industrial process automation. Key features of the LTP5902IPC-WHMA#PBF include transmit current of 5.4 mA to 9.7 mA depending on output power, receive current of 4.5 mA, an integrated ARM Cortex-M3 microprocessor for on-module application processing, and a hardware SPI host interface that exposes network and application services to an external microcontroller. Each mote functions as a full routing node, providing redundant self-healing mesh paths with ultra-low power consumption that enables multi-year battery life on a single cell. The module combines a precision radio with built-in time-synchronized channel hopping, AES-128 encryption, and self-forming/self-healing mesh capabilities that meet the WirelessHART (IEC 62591) standard. This architecture lets industrial operators deploy dense, deterministic sensor networks without manual RF tuning, and it lets battery-powered field instruments operate reliably for years in harsh plant environments. Typical applications include wireless process instrumentation, factory automation sensor networks, condition monitoring of rotating equipment, and battery-powered environmental sensors in oil and gas, pharmaceutical, and chemical plants. The Eterna family's ultra-low power consumption makes it suitable for intrinsically safe installations. When designing with this module, observe the host MCU's SPI timing requirements, provide a clean regulated 3.3 V source with adequate decoupling, and select an MMCX antenna whose VSWR matches the 2.4 GHz band. Verify regulatory certifications for your target region (FCC, IC, ETSI) and follow Dust Networks SmartMesh XT/XD antenna placement guidelines to maximize mesh link margin. This page synthesizes real-time distributor stock, parametric drop-in alternatives, and design notes that are not bundled in the manufacturer datasheet, giving engineers a single reference for selecting the LTP5902IPC-WHMA#PBF in industrial WirelessHART mesh deployments.
MAX-M10S-00B - u-blox M10 GNSS LCC Module | Ultra-Low-Power
The u-blox MAX-M10S-00B is an ultra-low-power, high-performance GNSS receiver module built on the u-blox M10 silicon platform and housed in a 9.7 x 10 mm LCC package with integrated TCXO, LNA, and SAW filter. The module concurrently tracks GPS, GLONASS, Galileo, and BeiDou constellations across the 1.561 GHz, 1.575 GHz, and 1.602 GHz GNSS bands, delivers a tracking sensitivity of -167 dBm and supports an update/data rate of 921.6 kbps on the UART/USB interface. The MAX-M10S-00B ordering code ships with ROM-based SPG 5.10 firmware on a 500-piece reel. What is a GNSS receiver module? A GNSS (Global Navigation Satellite System) receiver module is an integrated electronic assembly that combines the RF front-end (LNA, SAW filter, mixer), baseband correlator, GNSS processor, and a host interface (typically UART, I2C, or SPI) into a single surface-mount component. The host MCU sends configuration commands and receives NMEA or UBX protocol position/velocity/time (PVT) messages, removing the need to design a discrete RF chain. As a sub-category of RF receivers, GNSS modules sit inside the broader RF & Wireless category and serve as the position-and-time reference for any battery-powered or remote-connected embedded product. Key features of the MAX-M10S-00B include -167 dBm tracking sensitivity (acquiring and maintaining fix in weak-signal environments such as urban canyons), concurrent reception of four GNSS constellations for sub-2 m CEP positioning, integrated SAW+LNA RF front-end for immunity to out-of-band interferers, and ROM-based firmware that cannot be firmware-upgraded in the field. The module also supports both 1.8 V and 3.0 V host interfaces via the VCC and V_BCKP pins, simplifying migration from legacy NEO-M8 designs. The MAX-M10S-00B is built on the u-blox M10 architecture, manufactured in 28 nm CMOS, and consumes under 25 mW in continuous tracking mode - roughly 2x lower power than the MAX-M8 / NEO-M8 generation. The integrated TCXO provides fast warm-start times of a few seconds and stable reference for weak-signal acquisition, while the on-module SAW filter blocks cellular and Wi-Fi interferers common in asset-tracking deployments. Designers can evaluate the module with the SparkFun MAX-M10S Qwiic breakout or the MIKROE GNSS MAX Click board. Typical applications include battery-powered asset trackers, wearable fitness and pet-tracking devices, e-scooter and shared-mobility telematics, fleet management OBD dongles, and precision timing reference for cellular IoT modules. Engineers select the MAX-M10S-00B when four-constellation concurrent tracking and ultra-low power matter more than field firmware upgradeability. When designing with this device, ensure a clean VCC rail with a 1 uF + 100 nF decoupling pair close to the module pins, an active or passive GNSS antenna matched to 50 ohms, and a backup battery on V_BCKP for warm-start ephemeris retention. Choose the pin-compatible MAX-M10M-00B if you do not need the integrated TCXO and prefer a lower BOM cost; the package and pinout are identical for drop-in replacement. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet - information gain not duplicated on DigiKey, Mouser, or Octopart product pages.
MIFARE DESFire EV3 - AES-128 Contactless Multi-Application IC | NXP
The NXP MIFARE DESFire EV3 (MF3DHx3) is a high-security contactless multi-application IC for smart city services, combining ISO/IEC 14443-4 Type A communication, AES-128 and 3DES cryptographic protection, and EAL5+ Common Criteria certification in a contactless die/package suitable for inlay embedding. It delivers 2-32 KB of EEPROM user memory across the MF3DH23 (2 KB), MF3DH43 (4 KB), MF3DH83 (8 KB) and MF3DHR3 (32 KB variants per family naming) options with configurable ATS, optional RANDOM UID for privacy, and a unique 7-byte serial number per device. A contactless smartcard IC is a passive NFC chip that harvests energy from a reader's RF field, communicates over a 13.56 MHz HF air interface, and stores credentials and application data in secure non-volatile memory. MIFARE DESFire EV3 belongs to the NXP MIFARE DESFire platform family within the broader contactless smart card hierarchy, sitting between classic MIFARE Classic products and secure element SE chips, designed for high-throughput transit fare collection, secure access management, multi-application enterprise credentialing and NFC mobile deployment via MIFARE 2GO. Key features include AES-128 hardware acceleration alongside legacy 3DES support, Secure Dynamic Messaging (SDM) that mirrors secure OTPs as text into the NDEF message (compatible with NTAG DNA readers), SUN (Secure Unique NDEF) message authentication, mutual three-pass authentication per ISO/IEC 7816-4, and full backward compatibility with MIFARE DESFire EV1 and EV2 command sets. The chip is NFC Forum Type 4 Tag certified (Certificate ID 58652) and supports configurable ATS information for card personalization across diverse reader infrastructures. Typical applications include contactless transit ticketing, electronic toll collection, employee and student ID, hotel key cards, citizen eID cards, micropayment loyalty schemes, and mobile credential provisioning via NXP's MIFARE 2GO service. Applications running on DESFire EV3 can be deployed to NFC mobile phones without silicon changes, allowing issuers to manage physical and mobile credentials from a single personalization workflow. When designing with DESFire EV3, ensure the inlay antenna geometry matches the target reader's RF field strength, and verify that the SAM (Secure Access Module) on the reader side supports EV3's full command space including EV2/EV3 transaction MAC commands. Migration from EV1 or EV2 is largely command-compatible but requires re-personalization of application keys. This page synthesizes distributor availability, cross-family alternatives and design trade-offs not found in the manufacturer datasheet.
MJ001-01 - Wi-SUN FAN RF Communication Module | Star Instrument
The Shenzhen Star Instrument MJ001-01 is a Wi-SUN protocol radio frequency communication module integrating an SoC with RF transceiver and Wi-SUN protocol processing, interfacing to host devices via a serial (UART) interface for data and command exchange. It targets smart utility and AMI (Advanced Metering Infrastructure) applications requiring long-range, low-power mesh networking. Wi-SUN (Wireless Smart Utility Network) is an IEEE 802.15.4g-based mesh networking protocol standardized by the Wi-SUN Alliance for utility-scale IoT deployments such as smart meters, street lighting, and distribution automation. Unlike proprietary sub-GHz stacks, Wi-SUN FAN (Field Area Network) provides interoperable, self-healing mesh networks where every node can route traffic, giving utilities carrier-grade reliability and scalability across thousands of endpoints. Key characteristics of the MJ001-01 include its minimal size, low power consumption, and long transmission distance, per the official user manual. The module has passed Wi-SUN Alliance technical standard certification covering FAN PHY (Physical layer) conformance, and carries FCC ID 2A2X4-MJ001-01 for the US market. Star Instrument is recognized by the Wi-SUN Alliance as an early provider of Wi-SUN FAN V1.0 products deployed in overseas pilot and batch applications for automatic meter reading. Architecturally, the module embeds the complete Wi-SUN protocol stack on-chip, offloading RF timing, MAC, and mesh routing from the host MCU. Host integration is simplified to UART command/response traffic, reducing firmware development effort and certification scope for the end device. Typical applications include smart electricity, gas, and water metering, streetlight control networks, and distribution grid monitoring where multi-kilometer mesh links must operate for years on constrained power budgets. A key design consideration is verifying the module pinout, RF regulatory profile (region-specific frequency bands), and serial interface voltage levels against the manufacturer manual before layout, since public parametric data for this part is limited. This page synthesizes verified web sources - the official user manual, Wi-SUN Alliance product listing, and FCC filing - including certification status and sourcing context not consolidated in any single datasheet.
MM6108-MF08651-US - Wi-Fi HaLow 802.11ah Module 902-928MHz | Morse Micro
The Morse Micro MM6108-MF08651-US is a Wi-Fi HaLow RF module compliant with the IEEE 802.11ah sub-1 GHz standard, delivering data rates up to 32.5 Mbps with programmable operation in the 902 MHz to 928 MHz US ISM band. The module integrates an ultra-long-reach power amplifier (PA), a high-linearity low-noise amplifier (LNA), a SAW filter, a T/R switch, and a 32 MHz crystal oscillator on a compact certified module built around the Morse Micro MM6108 SoC. Wi-Fi HaLow is the sub-1 GHz variant of the Wi-Fi standard family (IEEE 802.11ah), designed as a low-power, long-range extension of conventional 2.4/5 GHz Wi-Fi. In the wireless connectivity hierarchy, it sits between short-range Wi-Fi/BLE and licensed-band LPWAN technologies such as LoRaWAN and NB-IoT, offering Wi-Fi-native IP connectivity with kilometer-scale reach and multi-year battery life potential. Key features include data rates up to 32.5 Mbps - roughly an order of magnitude beyond typical LPWAN throughput - long-range link budgets enabled by the ultra-long-reach PA, and low power consumption suited to battery-powered IoT endpoints. The integrated SAW filter and high-linearity LNA provide superior RF performance and out-of-band rejection, while WPA3 security support addresses modern Wi-Fi certification requirements. At the core of the module is the MM6108 single-chip SoC, which integrates the radio, PHY, and MAC functions and supports programmable operation from 850 MHz to 950 MHz at the chip level; the module is tuned and certified for the US 902-928 MHz band. The SoC architecture simplifies Wi-Fi HaLow connection to an external host processor over SDIO/USB-class interfaces, offloading the full 802.11 MAC from the host. Typical applications include smart home automation, industrial control and monitoring, security cameras, access control, and large-scale IoT/M2M sensor networks where conventional Wi-Fi range is insufficient. The Morse Micro MM6108-EKH05 v2 evaluation kit pairs this module with an STM32 MCU for rapid prototyping. Design consideration: because this variant is tuned for the US frequency band, designs targeting EU (863-868 MHz) or other regions must select a region-specific module variant or the chip-level MM6108 with custom RF front-end. This page synthesizes distributor pricing context, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, with pricing as of 2026-10-20.
MM610X-001 - Wi-Fi HaLow Sub-GHz IoT Module | AsiaRF
The AsiaRF MM610X-001 is a Wi-Fi HaLow Sub-GHz wireless module based on the Morse Micro MM6108 RF SOC, operating on the IEEE 802.11ah standard below 1 GHz in an LGA-42 stamp-form package with a U.FL connector for an external antenna. Wi-Fi HaLow is a low-power, long-range version of the IEEE 802.11 Wi-Fi standard, defined by the IEEE 802.11ah amendment. As a member of the wireless module family within RF modules and wireless connectivity semiconductors, it offloads the entire RF PHY and MAC from a host processor, exposing a simple digital interface to system designers. Key features include long-range sub-1 GHz connectivity that reaches approximately 10 times the distance and 100 times the area of traditional 2.4 GHz Wi-Fi, low power consumption optimized for battery-powered IoT nodes, and broad regulatory certification. According to Morse Micro, the MM610X-001 carries broader regulatory certification than any other module in the AsiaRF Wi-Fi HaLow range, allowing a single hardware design to ship to more export markets without board respins. The module integrates the MM6108 RF SOC, which implements the full 802.11ah protocol stack. Host connectivity is versatile: the module connects over UART, SDIO, SPI, or I2C, giving designers freedom to match it to low-end MCUs or Linux-class application processors. Community-documented bring-ups include Raspberry Pi 5 integration using Morse Micro MM610x software release packages under mainline Linux kernels. Typical applications include smart city infrastructure, security cameras and surveillance over long distances, industrial sensor networks, agricultural monitoring, and utility metering - scenarios where thousands of devices must connect securely through a single access point over kilometer-scale links. Design consideration: because HaLow operates in sub-GHz spectrum, antenna choice and regulatory region selection (channel plan) directly affect range and throughput; plan the U.FL antenna placement and verify the target market's certified band before production. Note the module requires a host driver stack from Morse Micro - budget integration time for the target OS. This page synthesizes distributor listings, manufacturer datasheets, regulatory information, and drop-in alternative analysis not found on any single source, providing a complete engineering view of the MM610X-001 for sourcing and design decisions.
MM8108-M20 - High-Power Wi-Fi HaLow Module 28.5dBm | Morse Micro
The Morse Micro MM8108-M20 is a high-power IEEE 802.11ah Wi-Fi HaLow transceiver module with up to 28.5 dBm transmit output power and a 902-928 MHz operating band, housed in a compact 18.5 mm x 14 mm surface-mount LGA-style footprint. Wi-Fi HaLow is the sub-1 GHz flavor of Wi-Fi defined by the IEEE 802.11ah standard. Unlike 2.4 GHz and 5 GHz Wi-Fi, HaLow trades bandwidth for range, wall penetration, and power efficiency, making it a wireless protocol positioned between legacy Wi-Fi and LPWAN technologies such as LoRa in the IoT connectivity hierarchy. The MM8108-M20 brings standard IP networking over sub-GHz links, so devices can use native TCP/IP stacks without gateways that translate protocols. Key features include transmit amplification up to 28.5 dBm delivered by an integrated external power amplifier, a surface acoustic wave (SAW) filter tuned to the 902-928 MHz North American band for exceptional receive sensitivity, and host connectivity via USB 2.0 High-Speed, SDIO, or SPI interfaces. The underlying MM8108 second-generation SoC integrates radio, PHY, and MAC functions compliant with IEEE 802.11ah and supports PHY rates up to 43.3 Mbps using 256-QAM modulation at 8 MHz bandwidth. The module is a single-chip solution built around the MM8108 SoC, which Morse Micro states delivers up to 3x more energy efficiency than the next best Wi-Fi SoC, extending battery life in power-sensitive designs. The SAW-filtered RF front end improves out-of-band rejection and receiver blocking performance, which is critical in the crowded sub-GHz license-exempt bands. Typical applications include industrial IoT sensor networks, security cameras and surveillance systems, smart building infrastructure, and long-range access points such as the Gateworks GW16170 M.2 2230 E-Key radio card, which uses the MM8108-M20 with up to +27.5 dBm transmit power in the 902-928 MHz band. Design consideration: the MM8108-M20 is region-specific to the 902-928 MHz band (FCC/IC markets); designs targeting other regulatory domains should evaluate the MM8108-MF15457 module covering 850-950 MHz instead. Antenna matching and thermal layout on the host PCB should follow the Morse Micro hardware design guide. This page synthesizes verified distributor and manufacturer data, drop-in alternative analysis, application guidance, and practical design notes not found in the manufacturer datasheet alone.
MM8108-MF15457 - Wi-Fi HaLow 802.11ah Module, 26dBm | Morse Micro
The Morse Micro MM8108-MF15457 is a fully integrated Wi-Fi HaLow (IEEE 802.11ah) transceiver module operating in the 850 MHz to 950 MHz sub-1 GHz license-exempt RF bands, delivering PHY data rates up to 43.3 Mbps with up to 26 dBm transmit power in a surface-mount RF PAD package. Wi-Fi HaLow is the IEEE 802.11ah amendment of the Wi-Fi standard, purpose-built for long-range, low-power connectivity. Unlike conventional 2.4 GHz or 5 GHz Wi-Fi, HaLow operates below 1 GHz, where propagation characteristics enable roughly ten times greater range and superior wall penetration, making it a key technology in the IoT connectivity hierarchy alongside LoRa, Sigfox, and NB-IoT for smart home, industrial, and infrastructure applications. Key features of the MM8108-MF15457 include compliance with IEEE 802.11ah, PHY rates up to 43.3 Mbps using world-first 256-QAM modulation at 8 MHz bandwidth, up to 26 dBm output power, and FCC, IC, CE, and Telec certifications for multi-region deployment. The module integrates the second-generation MM8108 Wi-Fi HaLow SoC with radio, PHY, and MAC functions on a single chip, together with integrated power amplifiers, drastically reducing external BOM complexity. The underlying MM8108 SoC is a highly integrated, ultra-low-power single-chip connectivity solution that Morse Micro claims delivers up to 3x more energy efficiency than the next best Wi-Fi SoC, and an OFDM transmitter up to 4x more energy-efficient than competing HaLow solutions. This translates directly into longer battery life for power-sensitive IoT endpoints without sacrificing throughput. Typical applications include smart home and security cameras requiring long-range video-capable links, industrial automation and sensor networks, and campus-scale IoT backhaul where a single HaLow access point can serve devices hundreds of meters away. The USB host interface (with SDIO and SPI support depending on loaded firmware) simplifies host integration. Design consideration: place the module per the MM8108-MF15457 Hardware Design Guide, keeping the RF PAD footprint and antenna keep-out areas intact, and confirm regional regulatory band limits (850-950 MHz varies by country) before certification. This page synthesizes distributor availability data, datasheet specifications, certification status, and practical design notes in one place - information not consolidated in the manufacturer datasheet alone.
MMM6000R2 - TRANSAAM TRANS MODULE | NXP / Freescale
The NXP (formerly Freescale Semiconductor) MMM6000R2 is a TRANSAAM transmit module classified as a specialized IC for cellular RF front-end applications. Per the verified product page on DigiKey and distributor descriptions, this part is described as a "TRANSAAM TRANS MODULE" and is associated with NXP/Freescale's legacy cellular RF power-management portfolio. The MMM6000R2 is sold primarily through authorized distributors including Rochester Electronics (the authorized afterlife source for NXP/Freescale legacy parts), LCSC, and several independent distributors; one marketplace listing (kstmicro.com) reports an inventory of 36,000 units, indicating healthy aftermarket availability despite an older product generation. What is a TRANSAAM module? In legacy cellular RF design, a TRANSAAM (transmit antenna amplifier module) is a specialized RF integrated circuit that integrates transmit signal-chain functions for 2G/3G/EDGE handset front-ends, often alongside the associated power-management biasing. TRANSAAM modules sit at the interface of the baseband transceiver and the power amplifier, providing controlled gain, ramping, and bias for the transmit path. Within the system hierarchy, a TRANSAAM belongs to: specialized IC -> RF front-end IC -> wireless transceiver subsystem -> cellular handset platform. Key features documented in the verified data include the long-standing NXP/Freescale RF integrated-circuit pedigree and the dual NXP / Freescale branding carried through from the Freescale acquisition by NXP Semiconductors. The part is listed as RoHS compliant per the kstmicro product page. Because the original datasheet (referenced as a 16-page PDF on alldatasheet for the related MMM6025 family) is no longer hosted on the NXP corporate site, this page synthesizes distributor catalog information and the related MMM60xx family datasheet to characterize the part. Modern equivalent parts from NXP's Airfast and RF GaN portfolios are recommended for new designs, with the MMM6000R2 used for maintenance of legacy EDGE/WCDMA platforms. Typical applications include EDGE/WCDMA handset transmit modules, legacy cellular infrastructure transmit chains, RF power-amplifier bias controllers, and repair/maintenance of older 2G/3G mobile platforms. The part is also encountered as a replacement component for OEM service stocks and as a long-term-supply (LTS) part via Rochester Electronics. Modern 4G LTE and 5G NR designs should migrate to NXP's Airfast MMIC portfolio or equivalent GaN/SiGe PAs. Design considerations for this part include verifying the exact RF frequency band coverage against your baseband transceiver before substitution, confirming the supply-voltage rail (the related MMM6025 family operates in the 3.0-4.5 V range), and budgeting for legacy-IC long lead times since authorized stock is increasingly limited to Rochester Electronics and independent distributors. Where possible, perform a substitution-validation bench test with the original baseband chipset to confirm transmit EVM, ACLR, and ramp-profile compliance. This page synthesizes distributor pricing, stock data, drop-in cross-reference options, and design notes not consolidated in the original manufacturer datasheet, providing an integrated engineering view that single distributor listings do not offer.