AD517JH Precision Op Amp, 1.5 V/us, 150 uV | Analog Devices
N.º de pieza: AD517JH ✓ ActivoAD517JH Descripción general
An operational amplifier, or op amp, is an active semiconductor that amplifies the voltage difference between its differential inputs. The AD517 belongs to the precision amplifier hierarchy: operational amplifier, precision amplifier, analog signal-conditioning IC, and semiconductor. Precision op amps are used where input offset, bias current, common-mode rejection, and low-frequency noise directly affect the accuracy of instrumentation, measurement, and analog signal-processing systems.
The AD517JH combines laser-trimmed offset characteristics with internally compensated operation. Its 150 uV offset voltage is supported by 3 uV/°C offset temperature drift, while the 5 nA input offset current and 1 nA input bias current help reduce errors when working with high-impedance sources. The 110 dB CMRR figure improves rejection of common-mode signals, and the 25 nV/√Hz noise density at 1 kHz is relevant to low-level signal acquisition.
The device uses a 5 nA input offset current, 4 mA quiescent current, and 10 mA supply-current-related operating condition within the manufacturer specification. Built-in compensation removes the need for an external compensation network in closed-loop amplifier configurations. The dual supply ranges of -18 V to -5 V and +5 V to +18 V permit operation from conventional positive and negative laboratory rails.
Typical applications include precision instrumentation, low-level sensor amplification, bridge-amplifier front ends, laboratory measurement equipment, and analog control systems. In a sensor interface, the AD517JH can amplify a small differential voltage while its offset and bias-current characteristics limit errors contributed by the amplifier itself. The 1.5 V/us slew rate is also useful where the required signal bandwidth and step response must be balanced against low-noise precision.
When inserting the AD517JH into a circuit, verify the differential and common-mode input limits for the selected supply voltage, especially near the positive and negative rail boundaries. Maintain adequate supply bypassing, keep feedback-loop routing compact, and account for the TO-99 package when constructing through-hole layouts or socket-based prototypes.
This page organizes the AD517JH electrical characteristics, package information, application guidance, and verified sourcing links. It also distinguishes documented AD517JH specifications from unspecified details and avoids presenting unconfirmed substitutes as pin-compatible replacements.
Alternativas directas para AD517JH — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
No hay alternativas directas disponibles para este producto.
Solicitar alternativasAD517JH Valores máximos y características eléctricas
| Product Type | Monolithic precision operational amplifier |
| Positive Supply Voltage Range | +5 V to +18 V |
| Negative Supply Voltage Range | -18 V to -5 V |
| Rango de temperatura de funcionamiento | 0°C to +70°C |
| Slew Rate | 1.5 V/µs |
| Input Offset Voltage | 150 µV |
| Input Offset Voltage Temperature Drift | 3 µV/°C |
| Input Offset Current | 5 nA |
| Input Bias Current | 1 nA |
| Common-Mode Rejection Ratio | 110 dB |
| Input Noise Density | 25 nV/√Hz at 1 kHz |
| Corriente en reposo | 4 mA |
| Corriente de alimentación | 10 mA |
| Compensation | Built-in compensation |
| Encapsulado | 8-pin TO-99 |
| Terminal Form | Wire |
| Package Shape | Round |
| Tipo de montaje | Through-hole |
| Temperature Grade | Commercial |
Guía de configuración de pines de AD517JH round
Configuración de pines para AD517JH (encapsulado round). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para AD517JH.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
AD517JH es adecuado para 6 aplicacións: Precision Sensor Signal Conditioning, Bridge-Amplifier Front End, Laboratory Voltage Buffer, Low-Level DC Amplifier, Analog Control and Feedback Systems, Precision Test and Measurement Equipment.
Precision Sensor Signal Conditioning
The AD517JH fits low-level sensor front ends where amplifier offset and bias current can materially affect measurement accuracy. Its 150 µV input offset voltage, 1 nA input bias current, and 110 dB CMRR help preserve small differential signals in the presence of supply or ground disturbances. The amplifier can be connected in an inverting or noninverting configuration around its balanced input pins, with feedback resistors selected from the source impedance and target gain. Because the device is internally compensated, designers can avoid an external compensation network, while the 25 nV/√Hz input noise at 1 kHz remains an important contributor when calculating total measurement noise.
Bridge-Amplifier Front End
The AD517JH is suitable for conditioning differential bridge outputs because its 110 dB common-mode rejection reduces errors from common-mode voltage appearing across a resistive sensor bridge. A 150 µV input offset voltage and 3 µV/°C offset drift remain important when the bridge imbalance is small, making the amplifier appropriate for laboratory and industrial instrumentation rather than only high-level signal paths. Its 1 nA input bias current is especially helpful when using high-impedance bridge and lead resistances. Select resistor values for the intended closed-loop gain and confirm that sensor excitation, common-mode level, and output range stay within the datasheet operating limits.
Laboratory Voltage Buffer
The AD517JH can serve as a unity-gain or buffered input stage in laboratory measurement equipment where a high-impedance source must drive a downstream analog circuit. The 1 nA input bias current limits the voltage error caused by high source resistance, while the 110 dB CMRR helps reject common-mode noise present on instrumentation leads. Built-in compensation simplifies a conventional voltage-feedback buffer, and the 1.5 V/µs slew rate provides useful response for moderate-bandwidth signal changes. For a precision instrument, evaluate offset and noise at the actual bandwidth rather than relying only on the 25 nV/√Hz density specified at 1 kHz.
Low-Level DC Amplifier
The AD517JH is appropriate for low-level DC signal amplification where the input is much smaller than the supply rails. Its laser-trimmed 150 µV offset specification and 3 µV/°C temperature coefficient support stable amplification of millivolt-level control or measurement signals. The 110 dB CMRR improves rejection of common-mode voltage in grounded industrial systems, while internal compensation avoids the need for a discrete frequency-compensation network. Designers should calculate gain-bandwidth and output-swing headroom for the selected feedback network, and should avoid treating the CMRR and noise figures as constant across every frequency without consulting the detailed frequency-response data.
Analog Control and Feedback Systems
The AD517JH can be used in analog servo loops, actuator feedback paths, and slow closed-loop control systems where accurate error amplification matters more than very high bandwidth. Its low 1 nA input bias current reduces excitation of sensitive source impedances, while the 150 µV offset sets a meaningful limit on near-zero error detection. The 1.5 V/µs slew rate supports normal correction signals without requiring a high-speed amplifier family. Stable implementation requires attention to feedback topology, load capacitance, supply bypassing, and loop compensation; the built-in compensation applies to the device configuration described in the Analog Devices AD517JH datasheet.
Precision Test and Measurement Equipment
The AD517JH is well matched to precision test and measurement equipment that handles small differential voltages, especially where supply noise and common-mode voltage are present. Its 110 dB CMRR and 25 nV/√Hz input noise at 1 kHz help preserve signal integrity at the input stage, while the 1 nA input bias current supports connections to high-impedance probes or sensors. The 0°C to +70°C commercial operating range suits laboratory and controlled industrial environments. For production test systems, evaluate offset calibration, temperature drift, input guarding, and resistor-network tolerance because these can dominate end-to-end accuracy even with a low-noise amplifier.
Datos de referencia de ingeniería para AD517JH — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto |
|---|---|
| Brand | Analog Devices |
| Package | 8-pin TO-99 |
| Positive Supply Voltage Range | +5 V to +18 V |
| Negative Supply Voltage Range | -18 V to -5 V |
| Input Offset Voltage | 150 µV |
| Input Offset Voltage Temperature Drift | 3 µV/°C |
| Slew Rate | 1.5 V/µs |
| Input Noise Density | 25 nV/√Hz at 1 kHz |
| Common-Mode Rejection Ratio | 110 dB |
| Input Bias Current | 1 nA |
| Operating Temperature Range | 0°C to +70°C |
| Compensation | Built-in compensation |
Notas de diseño
Use a ground plane and route the non-inverting input directly to the source reference with minimal loop area. For the inverting configuration, keep the feedback resistor and input resistor close to the amplifier pins to minimize parasitic capacitance and susceptibility to interference. The AD517JH is a through-hole TO-99 device, so pay particular attention to lead spacing, socket orientation, and the possibility of socket contact resistance in high-gain measurement circuits.
Bypass the positive and negative supply pins with ceramic capacitors selected for adequate effective capacitance at the operating frequency. Place each bypass capacitor close to its corresponding supply pin and include additional bulk decoupling where the op amp drives capacitive or dynamic loads. The AD517JH accepts +5 V to +18 V and -18 V to -5 V, but output swing and input common-mode range must also remain valid under the minimum supply conditions used by the design.
Do not select a substitute solely by lead count or by the input offset voltage alone. A valid replacement must also preserve the exact TO-99 lead assignment and meet the requirements for 1 nA-class bias current, 110 dB-class CMRR, 25 nV/√Hz-class noise, internal compensation, and the specified supply ranges. Verify the manufacturer pinout and electrical limits for every proposed substitute before changing an existing precision measurement design.
For low-level measurements, guard sensitive input nodes, use short leads, and avoid placing high-impedance traces beside switching-node or mains-derived wiring. Offset error and noise place practical limits on the measurable signal: the 150 µV offset is significant for microvolt-level sensing, and the 25 nV/√Hz density at 1 kHz should be integrated over the intended measurement bandwidth. Calibration can remove fixed offset but not time-varying drift or uncorrelated noise.
Información de cumplimiento
No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified for AD517JH. AEC-Q100 is not applicable because the AD517JH is a commercial-temperature precision operational amplifier rather than an automotive-qualified device.