Analog Devices

AD517JH Precision Op Amp, 1.5 V/us, 150 uV | Analog Devices

부품 번호: AD517JH ✓ 활성
+5 V to +18 V Vdss 5 nA Id 8-pin TO-99 Package
MOQ: 1 |

AD517JH 개요

The Analog Devices AD517JH is a monolithic precision operational amplifier with a 1.5 V/us slew rate, 150 uV input offset voltage, 110 dB common-mode rejection, and 25 nV/√Hz input noise at 1 kHz, housed in an 8-pin TO-99 package. It operates from -18 V to -5 V and +5 V to +18 V, supports a commercial temperature range of 0°C to +70°C, and requires no external compensation.

An operational amplifier, or op amp, is an active semiconductor that amplifies the voltage difference between its differential inputs. The AD517 belongs to the precision amplifier hierarchy: operational amplifier, precision amplifier, analog signal-conditioning IC, and semiconductor. Precision op amps are used where input offset, bias current, common-mode rejection, and low-frequency noise directly affect the accuracy of instrumentation, measurement, and analog signal-processing systems.

The AD517JH combines laser-trimmed offset characteristics with internally compensated operation. Its 150 uV offset voltage is supported by 3 uV/°C offset temperature drift, while the 5 nA input offset current and 1 nA input bias current help reduce errors when working with high-impedance sources. The 110 dB CMRR figure improves rejection of common-mode signals, and the 25 nV/√Hz noise density at 1 kHz is relevant to low-level signal acquisition.

The device uses a 5 nA input offset current, 4 mA quiescent current, and 10 mA supply-current-related operating condition within the manufacturer specification. Built-in compensation removes the need for an external compensation network in closed-loop amplifier configurations. The dual supply ranges of -18 V to -5 V and +5 V to +18 V permit operation from conventional positive and negative laboratory rails.

Typical applications include precision instrumentation, low-level sensor amplification, bridge-amplifier front ends, laboratory measurement equipment, and analog control systems. In a sensor interface, the AD517JH can amplify a small differential voltage while its offset and bias-current characteristics limit errors contributed by the amplifier itself. The 1.5 V/us slew rate is also useful where the required signal bandwidth and step response must be balanced against low-noise precision.

When inserting the AD517JH into a circuit, verify the differential and common-mode input limits for the selected supply voltage, especially near the positive and negative rail boundaries. Maintain adequate supply bypassing, keep feedback-loop routing compact, and account for the TO-99 package when constructing through-hole layouts or socket-based prototypes.

This page organizes the AD517JH electrical characteristics, package information, application guidance, and verified sourcing links. It also distinguishes documented AD517JH specifications from unspecified details and avoids presenting unconfirmed substitutes as pin-compatible replacements.

드롭인 대체품: AD517JH — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

이 제품에는 사용 가능한 드롭인 대체품이 없습니다.

대체품 요청

AD517JH 최대 정격 & 전기적 특성

Product Type Monolithic precision operational amplifier
Positive Supply Voltage Range +5 V to +18 V
Negative Supply Voltage Range -18 V to -5 V
동작 온도 범위 0°C to +70°C
Slew Rate 1.5 V/µs
Input Offset Voltage 150 µV
Input Offset Voltage Temperature Drift 3 µV/°C
Input Offset Current 5 nA
Input Bias Current 1 nA
Common-Mode Rejection Ratio 110 dB
Input Noise Density 25 nV/√Hz at 1 kHz
대기 전류 4 mA
공급 전류 10 mA
Compensation Built-in compensation
패키지 8-pin TO-99
Terminal Form Wire
Package Shape Round
실장 유형 Through-hole
Temperature Grade Commercial

AD517JH round 핀 구성 가이드

AD517JH(round 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.

AD517JH의 round 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: AD517JH.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

AD517JH 적합 용도: 6 애플리케이션s: Precision Sensor Signal Conditioning, Bridge-Amplifier Front End, Laboratory Voltage Buffer, Low-Level DC Amplifier, Analog Control and Feedback Systems, Precision Test and Measurement Equipment.

📡

Precision Sensor Signal Conditioning

The AD517JH fits low-level sensor front ends where amplifier offset and bias current can materially affect measurement accuracy. Its 150 µV input offset voltage, 1 nA input bias current, and 110 dB CMRR help preserve small differential signals in the presence of supply or ground disturbances. The amplifier can be connected in an inverting or noninverting configuration around its balanced input pins, with feedback resistors selected from the source impedance and target gain. Because the device is internally compensated, designers can avoid an external compensation network, while the 25 nV/√Hz input noise at 1 kHz remains an important contributor when calculating total measurement noise.

🏭

Bridge-Amplifier Front End

The AD517JH is suitable for conditioning differential bridge outputs because its 110 dB common-mode rejection reduces errors from common-mode voltage appearing across a resistive sensor bridge. A 150 µV input offset voltage and 3 µV/°C offset drift remain important when the bridge imbalance is small, making the amplifier appropriate for laboratory and industrial instrumentation rather than only high-level signal paths. Its 1 nA input bias current is especially helpful when using high-impedance bridge and lead resistances. Select resistor values for the intended closed-loop gain and confirm that sensor excitation, common-mode level, and output range stay within the datasheet operating limits.

🔬

Laboratory Voltage Buffer

The AD517JH can serve as a unity-gain or buffered input stage in laboratory measurement equipment where a high-impedance source must drive a downstream analog circuit. The 1 nA input bias current limits the voltage error caused by high source resistance, while the 110 dB CMRR helps reject common-mode noise present on instrumentation leads. Built-in compensation simplifies a conventional voltage-feedback buffer, and the 1.5 V/µs slew rate provides useful response for moderate-bandwidth signal changes. For a precision instrument, evaluate offset and noise at the actual bandwidth rather than relying only on the 25 nV/√Hz density specified at 1 kHz.

⚡

Low-Level DC Amplifier

The AD517JH is appropriate for low-level DC signal amplification where the input is much smaller than the supply rails. Its laser-trimmed 150 µV offset specification and 3 µV/°C temperature coefficient support stable amplification of millivolt-level control or measurement signals. The 110 dB CMRR improves rejection of common-mode voltage in grounded industrial systems, while internal compensation avoids the need for a discrete frequency-compensation network. Designers should calculate gain-bandwidth and output-swing headroom for the selected feedback network, and should avoid treating the CMRR and noise figures as constant across every frequency without consulting the detailed frequency-response data.

🖥️

Analog Control and Feedback Systems

The AD517JH can be used in analog servo loops, actuator feedback paths, and slow closed-loop control systems where accurate error amplification matters more than very high bandwidth. Its low 1 nA input bias current reduces excitation of sensitive source impedances, while the 150 µV offset sets a meaningful limit on near-zero error detection. The 1.5 V/µs slew rate supports normal correction signals without requiring a high-speed amplifier family. Stable implementation requires attention to feedback topology, load capacitance, supply bypassing, and loop compensation; the built-in compensation applies to the device configuration described in the Analog Devices AD517JH datasheet.

📺

Precision Test and Measurement Equipment

The AD517JH is well matched to precision test and measurement equipment that handles small differential voltages, especially where supply noise and common-mode voltage are present. Its 110 dB CMRR and 25 nV/√Hz input noise at 1 kHz help preserve signal integrity at the input stage, while the 1 nA input bias current supports connections to high-impedance probes or sensors. The 0°C to +70°C commercial operating range suits laboratory and controlled industrial environments. For production test systems, evaluate offset calibration, temperature drift, input guarding, and resistor-network tolerance because these can dominate end-to-end accuracy even with a low-noise amplifier.

What are the key specifications of AD517JH that engineers should know?
The AD517JH is a precision, internally compensated operational amplifier with 150 µV input offset voltage, 3 µV/°C offset drift, 110 dB CMRR, 25 nV/√Hz input noise at 1 kHz, and a 1.5 V/µs slew rate. According to the Analog Devices AD517JH datasheet, the amplifier supports positive supplies from +5 V to +18 V and negative supplies from -18 V to -5 V. It is packaged in an 8-lead round TO-99 package for through-hole mounting.
What is the operating voltage of AD517JH?
The AD517JH operates from +5 V to +18 V on the positive supply and -18 V to -5 V on the negative supply. According to the Analog Devices AD517JH datasheet, these ranges support conventional laboratory and industrial power rails while excluding operation from a single positive supply. Confirm the output swing and input common-mode limits at the exact supply voltages used in the design.
What is the input offset voltage of AD517JH?
The AD517JH has a typical input offset voltage of 150 µV. According to the Analog Devices AD517JH datasheet, its input offset voltage temperature coefficient is 3 µV/°C. These figures are particularly important when the amplifier handles millivolt-level sensor signals because input offset voltage is added directly to the signal being amplified and can therefore reduce measurement accuracy.
What is the slew rate and noise performance of AD517JH?
The AD517JH provides a 1.5 V/µs slew rate and an input noise density of 25 nV/√Hz at 1 kHz. According to the Analog Devices AD517JH datasheet, these characteristics support precision low-level signal amplification without requiring an external compensation network. The slew rate determines large-signal response, while the noise density contributes to the total input-referred noise of the completed measurement channel.
Where to download the AD517JH datasheet PDF?
The AD517JH datasheet documentation is available through the linked AD517JH datasheet page, which identifies Analog Devices as the manufacturer and describes the device as a low-cost, laser-trimmed precision operational amplifier. Use the Analog Devices technical documentation for final design decisions, including maximum ratings, test conditions, and detailed application information. Request a Quote on this page for current sourcing and order handling.
Where can I find the AD517JH pinout and package information?
The AD517JH uses an 8-terminal, round TO-99 through-hole package with wire leads. The AD517JH package information identifies eight terminals, a commercial temperature grade, and a minimum operating temperature of 0°C. Before wiring the device, assign the physical leads using the pin-description diagram in the manufacturer datasheet and the package drawing associated with your exact ordering code.
Is AD517JH suitable for precision instrumentation and sensor measurement?
The AD517JH is suitable for precision instrumentation because its 150 µV offset voltage, 1 nA input bias current, 110 dB CMRR, and 25 nV/√Hz input noise limit several common amplifier error sources. According to the Analog Devices AD517JH datasheet, the device also includes internal compensation. Its suitability still depends on the sensor source impedance, signal bandwidth, common-mode range, and required accuracy.
Can AD517JH operate with negative supply voltages?
The AD517JH supports a negative supply range from -18 V to -5 V. According to the Analog Devices AD517JH datasheet, the positive supply range is +5 V to +18 V, allowing conventional dual-rail operation. Negative supply operation is useful in bipolar signal conditioning, but the input and output excursions must remain within the limits specified for the actual positive and negative supply voltages.
Does AD517JH need an external compensation capacitor?
The AD517JH uses built-in compensation and does not require an external compensation capacitor for normal voltage-feedback operation. According to the Analog Devices AD517JH datasheet, this simplifies the implementation of stable closed-loop amplifier stages. Gain-bandwidth and stability still depend on the selected feedback network, load, output-device configuration, and operating frequency, so the recommended circuit configurations should be followed.
Where to buy AD517JH online?
The AD517JH can be requested through the Request a Quote form on this XAIPART product page, where the requested quantity and intended package configuration can be communicated. Current commercial terms should be confirmed through that form rather than inferred from historical catalog records. The AD517JH is an 8-pin TO-99 operational amplifier, so confirm the exact suffix and lead configuration before ordering.
What is the price of AD517JH?
The current AD517JH commercial price is not stated in the manufacturer specification, and a live quote is required for this through-hole precision operational amplifier. Use the Request a Quote form on this page to request current pricing, minimum order quantity, and availability for the exact AD517JH ordering code. The form is the appropriate channel for price and stock confirmation rather than a static product-page amount.
What is the lead time and stock status for AD517JH?
Current AD517JH stock and lead time must be confirmed through the Request a Quote form on this page. The part is an 8-pin TO-99 precision operational amplifier with a 0°C to +70°C commercial temperature range, so quote requests should state the required quantity and date of need. Requesting a formal quotation allows production planning to use the latest purchasing status.
Is AD517JH in stock?
AD517JH availability is subject to current inventory and purchasing status, which should be checked through the Request a Quote form on this page. Do not treat a historical catalog listing as a reservation or guaranteed stock position. Include the required quantity, package suffix, and delivery target in the request to obtain a current answer for the exact AD517JH.
What is the best drop-in replacement for AD517JH?
No confirmed pin-compatible drop-in replacement for the AD517JH is identified in the manufacturer documentation or verified cross-reference information. A replacement should not be selected solely because it has eight leads or similar offset voltage; the input bias current, offset drift, CMRR, noise, compensation, supply range, and exact lead assignment must all be checked. Submit the candidate MPN and application requirements through Request a Quote for engineering review.
What can replace AD517JH in a precision amplifier circuit?
A valid AD517JH replacement must preserve the 8-pin TO-99 footprint and meet the circuit's requirements for 150 µV-class offset, low bias current, 110 dB-class CMRR, noise, slew rate, supply voltage, and internal compensation. No substitute is promoted as drop-in without verified pin and parameter matching. Provide the candidate part number and the original circuit requirements for a compatibility assessment through Request a Quote.

엔지니어링 참조 데이터: AD517JH — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose the AD517JH for a through-hole precision amplifier design requiring low input bias current, low input noise, high common-mode rejection, and conventional dual-rail operation. Its 150 µV offset, 1 nA input bias current, 110 dB CMRR, 25 nV/√Hz noise density, and internal compensation make it appropriate for instrumentation and laboratory measurement stages. The commercial 0°C to +70°C rating is suitable for controlled indoor and industrial environments. A different device should be selected when the design requires a wider temperature range, a surface-mount package, rail-to-rail input/output operation, or substantially lower offset and noise. Because the TO-99 footprint has no confirmed drop-in substitute in the available technical references, evaluate any proposed replacement against pin assignment, bias current, CMRR, noise, slew rate, compensation, and supply limits before committing it to an existing board.

대체품과의 비교

파라미터 이 제품
Brand Analog Devices
Package 8-pin TO-99
Positive Supply Voltage Range +5 V to +18 V
Negative Supply Voltage Range -18 V to -5 V
Input Offset Voltage 150 µV
Input Offset Voltage Temperature Drift 3 µV/°C
Slew Rate 1.5 V/µs
Input Noise Density 25 nV/√Hz at 1 kHz
Common-Mode Rejection Ratio 110 dB
Input Bias Current 1 nA
Operating Temperature Range 0°C to +70°C
Compensation Built-in compensation

설계 노트

Use a ground plane and route the non-inverting input directly to the source reference with minimal loop area. For the inverting configuration, keep the feedback resistor and input resistor close to the amplifier pins to minimize parasitic capacitance and susceptibility to interference. The AD517JH is a through-hole TO-99 device, so pay particular attention to lead spacing, socket orientation, and the possibility of socket contact resistance in high-gain measurement circuits.

Bypass the positive and negative supply pins with ceramic capacitors selected for adequate effective capacitance at the operating frequency. Place each bypass capacitor close to its corresponding supply pin and include additional bulk decoupling where the op amp drives capacitive or dynamic loads. The AD517JH accepts +5 V to +18 V and -18 V to -5 V, but output swing and input common-mode range must also remain valid under the minimum supply conditions used by the design.

Do not select a substitute solely by lead count or by the input offset voltage alone. A valid replacement must also preserve the exact TO-99 lead assignment and meet the requirements for 1 nA-class bias current, 110 dB-class CMRR, 25 nV/√Hz-class noise, internal compensation, and the specified supply ranges. Verify the manufacturer pinout and electrical limits for every proposed substitute before changing an existing precision measurement design.

For low-level measurements, guard sensitive input nodes, use short leads, and avoid placing high-impedance traces beside switching-node or mains-derived wiring. Offset error and noise place practical limits on the measurable signal: the 150 µV offset is significant for microvolt-level sensing, and the 25 nV/√Hz density at 1 kHz should be integrated over the intended measurement bandwidth. Calibration can remove fixed offset but not time-varying drift or uncorrelated noise.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified for AD517JH. AEC-Q100 is not applicable because the AD517JH is a commercial-temperature precision operational amplifier rather than an automotive-qualified device.

데이터 검증일: 2026-11-18 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

AD517JH datasheet AD517JH pinout AD517JH datasheet pdf AD517JH specifications AD517JH price AD517JH stock AD517JH equivalent AD517JH replacement AD517JH TO-99 pinout AD517JH precision op amp AD517JH vs OP07 Analog Devices AD517JH

관련 부품 & 용어

Analog Devices AD517JH AD517 precision operational amplifier operational amplifier precision amplifier analog signal-conditioning IC semiconductor input offset voltage input bias current common-mode rejection ratio CMRR input noise density slew rate built-in compensation TO-99 8-pin TO-99 through-hole package precision instrumentation bridge amplifier sensor signal conditioning laboratory measurement dual-rail operation laser-trimmed offset
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기