Analog Devices

AD521LDZ - 1000x Programmable Gain Instrumentation Amplifier | Analog Devices

N.º de pieza: AD521LDZ ✗ Fin de vida
14-CDIP, 0.300 in (7.62 mm) pitch Package
MOQ: 1 |

AD521LDZ Descripción general

The Analog Devices AD521LDZ is a monolithic instrumentation amplifier with programmable gains up to 1000, one amplifier circuit, and a 14-CDIP package. It is the L-grade version of the AD521 family and is specified from 0°C to +70°C. Key electrical characteristics include a minimum common-mode rejection ratio of 110 dB, a maximum input drift of 2 pV/°C for the L grade, and a slew rate of 10 V/µs.

An instrumentation amplifier is a differential analog signal-conditioning device used to amplify the voltage difference between two inputs while rejecting common-mode voltage and providing high input impedance. Within the broader signal-chain hierarchy, an instrumentation amplifier is an analog amplifier, an integrated circuit, and a precision measurement component. Its typical role is to condition low-level sensor outputs before conversion, display, or further signal processing.

The AD521 offers programmable gain settings covering the range up to 1000, allowing one circuit to serve multiple signal amplitudes. Its high CMRR reduces errors when the differential sensor signal is small relative to a common-mode voltage. Complete input protection supports power-on and power-off conditions, while the monolithic implementation reduces the component count compared with a discrete three-op-amp instrumentation-amplifier design.

The L grade emphasizes low drift and high linearity while operating from 0°C to +70°C. A 10 V/µs slew rate supports signal amplitudes and bandwidths above those of slow precision instrumentation amplifiers. The 14-CDIP package is intended for through-hole assembly and offers a practical option for industrial, laboratory, and legacy control systems that already use ceramic dual-inline package footprints.

Typical uses include bridge-transducer measurement, pressure and load-cell signal conditioning, biomedical instrumentation, current-loop sensing, and precision data-acquisition front ends. In each case, the AD521LDZ converts a small differential input into a larger single-ended voltage while attenuating common-mode interference. Designers must select the appropriate gain setting and confirm that input and output operating ranges do not clip the signal chain.

For reliable operation, use the manufacturer's specified supply voltage, gain-control logic, and output-settling conditions. Ceramic-DIP sockets and sockets with suitable contact resistance and insulation characteristics should be considered when field replacement or maintenance is important. Board layout should keep sensitive input traces short, separate from switching nodes and high-current return paths.

This page combines package, grade, gain, CMRR, drift, and application guidance with drop-in family alternatives and design-focused comparisons. It also organizes sourcing questions around the AD521LDZ while keeping the electrical distinctions between supported grade and package options visible for engineering review.

Alternativas directas para AD521LDZ — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con AD521LDZ (mismo factor de forma y huella) — difiere en Temperature Grade, Mounting Type, Package, Product Type.

Analog Devices
Temperature Grade: Commercial
Product Type: Instrumentation amplifier
Comparar con AD521LDZ →
Analog Devices
Temperature Grade: 0°C to +70°C for K grade
Mounting Type: Through-hole ceramic DIP
Package: 14-pin ceramic DIP
Comparar con AD521LDZ →

AD521KDZ

✅ Sustitución directa
Analog Devices
📦 14-CDIP (0.300 in, 7.62 mm pitch)
Monolithic instrumentation amplifier · 1 circuit · 14-CDIP · 14 pins · 40 MHz · External resistor · Differential input · Built in

Consulte el precio

Ver hoja de datos →

AD521JDZ

✅ Sustitución directa ⚠️ Especificaciones sin verificar
Analog Devices
📦 14-CDIP (0.300 in, 7.62 mm pitch)
Instrumentation amplifier · 1 circuit · 14 terminals · 14-lead ceramic DIP (14-CDIP) · Through-hole · Rectangular · Commercial · 0°C to +70°C

Consulte el precio

Ver hoja de datos →

AD521BDZ

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 14-CDIP (0.300 in, 7.62 mm pitch)
Uses the same 14-CDIP footprint and 1-to-1000 programmable gain range; the B-grade drift and linearity differ from the L grade.

📋 Alternativa de referencia (no en el catálogo)

AD521CDZ

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 14-CDIP (0.300 in, 7.62 mm pitch)
Uses the same 14-CDIP footprint and 1-to-1000 programmable gain range; the C-grade drift and linearity differ from the L grade.

📋 Alternativa de referencia (no en el catálogo)

AD521SDZ

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 14-CDIP (0.300 in, 7.62 mm pitch)
Uses the same 14-CDIP footprint and 1-to-1000 programmable gain range; extends operation from the L grade's 0°C to +70°C to −55°C to +125°C.

📋 Alternativa de referencia (no en el catálogo)

AD521LDZ Valores máximos y características eléctricas

Device Type Monolithic instrumentation amplifier
Number of Amplifier Circuits 1 circuit
Programmable Gain Up to 1000:1
Common-Mode Rejection Ratio 110 dB minimum
Maximum Input Drift, L Grade 2 pV/°C maximum
Slew Rate 10 V/µs
Temperature Grade L grade
Rango de temperatura de funcionamiento 0°C to +70°C
Input Protection Complete input protection at power-on and power-off
Encapsulado 14-CDIP, 0.300 in (7.62 mm) pitch
Packaging Type Tube
Tipo de montaje Through-hole
Differential Input Yes
Programmable Gain Control Digital control

Guía de configuración de pines de AD521LDZ 14-cdip, 0.300 in (7.62 mm) pitch

Configuración de pines para AD521LDZ (encapsulado 14-cdip, 0.300 in (7.62 mm) pitch). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.

Diagrama de patillaje del encapsulado 14-cdip, 0.300 in (7.62 mm) pitch para AD521LDZ

No hay datos detallados de patillaje disponibles para AD521LDZ.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

AD521LDZ es adecuado para 6 aplicacións: Load-Cell and Bridge-Sensor Measurement, Precision Industrial Data Acquisition, Biomedical and Diagnostic Instrumentation, Current-Loop Sensor Conditioning, Laboratory and Instrumentation Signal Chains, Power and Motor Monitoring.

⚖️

Load-Cell and Bridge-Sensor Measurement

The AD521LDZ is well suited to conditioning small differential bridge outputs because its programmable gain reaches 1000 and its CMRR is 110 dB minimum. The common-mode rejection helps prevent bridge excitation voltage from appearing as measurement error, while the L grade limits input drift to 2 pV/°C maximum over 0°C to +70°C. Place the device close to the bridge, use guarded input routing, and confirm that the selected gain and bridge excitation keep the output within the valid swing range.

🏭

Precision Industrial Data Acquisition

The AD521LDZ can serve as the analog front end for industrial data-acquisition systems carrying sensor voltages near the lower end of the ADC range. Programmable gain up to 1000 allows a designer to scale several transducer classes without changing the board, while 110 dB minimum CMRR improves rejection of shared supply and ground disturbances. The 0°C to +70°C L-grade specification is appropriate for many enclosure environments, but an extended-temperature grade is needed outside that range.

💊

Biomedical and Diagnostic Instrumentation

The AD521LDZ fits low-level biomedical measurement chains where patient or physiological signals are differential and small relative to common-mode voltage. Its 110 dB minimum CMRR supports rejection of common-mode interference, and programmable gain up to 1000 allows amplification close to the sensor before cable noise and downstream conversion errors accumulate. The L grade's 2 pV/°C maximum drift supports temperature-stable measurements from 0°C to +70°C, subject to isolation, leakage, and safety requirements outside the amplifier itself.

⚡

Current-Loop Sensor Conditioning

The AD521LDZ can amplify the voltage generated by a current-to-voltage conversion element in a 4-20 mA instrumentation loop. Differential input architecture and 110 dB minimum CMRR help reject voltage shared by both input nodes, while programmable gain up to 1000 provides useful scaling for millivolt-level shunt voltages. Verify the input common-mode range against the loop voltage, maintain input impedance appropriate for the transmitter, and avoid excessive gain that could move the output outside its linear range.

🔬

Laboratory and Instrumentation Signal Chains

The AD521LDZ is useful in laboratory front ends that measure differential signals while presenting a controlled, amplified single-ended output to a data logger or display. Its programmable gain up to 1000 supports several input ranges, and the 10 V/µs slew rate provides useful speed for larger output transitions. The 14-CDIP format also simplifies use in educational, legacy, and hand-built instrumentation where a through-hole package and replaceable device are preferred over a fine-pitch surface-mount design.

🏭

Power and Motor Monitoring

The AD521LDZ can condition differential sensing elements used to monitor current, voltage, position, or vibration in power and motor systems. High CMRR reduces errors when sensing signals share a large common-mode voltage, while the gain range up to 1000 provides flexibility across sensor outputs. Keep the 0°C to +70°C operating rating in view, isolate sensitive routes from switching nodes, and verify that transients and surge conditions do not exceed the manufacturer's absolute maximum ratings.

What is the AD521LDZ?
The AD521LDZ is a monolithic instrumentation amplifier from Analog Devices with one amplifier circuit, programmable gain up to 1000, and a 14-CDIP package. According to the Analog Devices AD521 product page, it is the L-grade device intended for low-drift, high-linearity operation from 0°C to +70°C. It accepts differential inputs and is suitable for sensor, bridge, biomedical, and precision data-acquisition front ends.
What are the key specifications of AD521LDZ that engineers should know?
The AD521LDZ combines programmable gain up to 1000, 110 dB minimum CMRR, 10 V/µs slew rate, and a maximum input drift of 2 pV/°C in the L grade. The Analog Devices product description identifies it as a one-circuit monolithic instrumentation amplifier in a 14-CDIP package. Its 0°C to +70°C specification distinguishes it from the S-grade device rated to −55°C to +125°C.
What is the gain range of AD521LDZ?
The AD521LDZ supports programmable gain up to 1000, as stated by Analog Devices for the AD521 family. The lower end of the supported gain range is not stated in the product-page summary and must be confirmed in the manufacturer data sheet before setting the gain-control logic. Designers should also verify that the selected gain produces an output below the device's allowable output swing.
Where can I download the AD521LDZ datasheet PDF?
The official AD521LDZ documentation is available through the Analog Devices product page at https://www.analog.com/en/products/ad521.html, which links the family data sheet and product information. Use the manufacturer data sheet for the complete pin-description table, electrical characteristics, gain-control truth table, supply limits, and ordering guide. A separate mirrored PDF is also listed for AD521LDZ, but the manufacturer page is the preferred starting point.
Where can I find the AD521LDZ pinout?
The AD521LDZ pinout is identified in the pin-configuration section of the Analog Devices AD521 family data sheet and corresponds to the 14-CDIP outline. The package is a 0.300 in (7.62 mm) pitch ceramic dual-inline package. Use the manufacturer's pin-description table when assigning supply, gain-control, differential-input, and output connections rather than relying on a generic package drawing.
AD521LDZ vs AD521KDZ - which is better for precision measurement?
The AD521LDZ is the L grade, emphasizing lower drift and higher linearity, while the AD521KDZ is the K grade with lower drift than the J grade. Both are AD521-family monolithic instrumentation amplifiers offered in the same 14-CDIP format. Choose AD521LDZ when its lower-drift L-grade characteristics are required; choose AD521KDZ when its grade-specific accuracy is sufficient and device availability is more important.
When should I choose AD521LDZ over AD521KDZ?
Choose AD521LDZ when the design needs the AD521 family's L-grade low-drift and high-lineality positioning at 0°C to +70°C. The L grade has a maximum input drift of 2 pV/°C according to the AD521 family description. AD521KDZ remains a same-package family alternative when the K grade meets the measurement requirement, but its exact drift and error limits should be checked against the system error budget.
Is AD521LDZ suitable for bridge and load-cell measurement?
Yes, AD521LDZ is suitable for bridge-transducer and load-cell front ends because it accepts differential signals, offers programmable gain up to 1000, and provides 110 dB minimum CMRR. Those characteristics help reject common-mode excitation voltage and preserve small differential outputs. The input bias current, input common-mode range, and offset voltage must be checked against the bridge impedance and excitation level before finalizing the circuit.
What is the best drop-in replacement for AD521LDZ?
The closest documented drop-in family option is the AD521KDZ because it uses the same AD521 architecture and 14-CDIP package while changing the precision grade. Other AD521 grade options with the same DZ package suffix may support footprint reuse, but grade-specific accuracy, temperature range, and availability require verification. A replacement should not be selected solely by package and amplifier count.
Can AD521KDZ replace AD521LDZ on the same PCB?
The AD521KDZ can generally be used as a same-package AD521-family replacement, but it is not an exact performance match for the AD521LDZ. The AD521LDZ is the L grade with lower drift and high linearity, whereas the AD521KDZ is the K grade. Confirm the power-up state of the gain-control pins, supply requirements, output range, and the required grade-specific error limits before substitution.
What is the best Analog Devices equivalent for AD521LDZ?
The AD521KDZ is the best-supported Analog Devices equivalent in the family listing because it is an AD521-series instrumentation amplifier in the same 14-CDIP package. It changes the precision grade rather than the fundamental amplifier category. If the AD521KDZ does not meet the required drift or linearity, review another AD521 grade with the DZ package suffix rather than assuming electrical equivalence.
Where to buy AD521LDZ online?
Use the Request a Quote form on this page to request AD521LDZ availability, order quantities, and a current quotation. The form is the direct sourcing path for this listing and avoids presenting a potentially stale catalog quantity break. For technical confirmation, use the official Analog Devices AD521 product page and data sheet to validate package, grade, and lifecycle requirements.
What is the price of AD521LDZ?
The current commercial quotation for AD521LDZ is generated through the Request a Quote form on this page. Pricing depends on order quantity, packaging, availability, and contractual terms, so a static unit figure should not be treated as a guaranteed quotation. Use the form with the required part number, package configuration, and target quantity so the returned commercial offer reflects the actual request.
What is the lead time for AD521LDZ?
The current lead time for AD521LDZ should be requested through the Request a Quote form on this page. Lead time can vary with order quantity, manufacturing status, and inventory position, so it is not appropriate to infer a fixed delivery interval from a catalog listing. Include the tube packaging requirement and any production schedule constraints with the request.
Is AD521LDZ in stock?
Current AD521LDZ stock status should be confirmed through the Request a Quote form on this page. A distributor search result can reflect an earlier inventory snapshot rather than a guaranteed allocation, so it should not be treated as a current stock commitment. The quote request can specify quantity, tube-packaging preference, acceptable ship date, and whether multiple production releases are permitted.

Datos de referencia de ingeniería para AD521LDZ — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose the AD521LDZ when the design needs the AD521 family's L-grade low-drift and high-linearity position, particularly for bridge, load-cell, biomedical, or laboratory measurements operating from 0°C to +70°C. Its programmable gain up to 1000, 110 dB minimum CMRR, and 10 V/µs slew rate make it suitable for small differential signals requiring substantial amplification. Choose AD521KDZ when its precision grade meets the error budget and it offers better sourcing or cost alignment. AD521JDZ is a lower-grade same-footprint option when the additional drift or linearity of the L grade is unnecessary. AD521BDZ and AD521CDZ are appropriate only after their individual grade limits have been checked against the design. Select AD521SDZ when operation from −55°C to +125°C is required. For every replacement, confirm pin compatibility, gain-control logic, input and output limits, supply requirements, and settling performance before releasing the PCB.

Comparación con alternativas

Parámetro Este producto AD521KDZ AD521JDZ AD521BDZ AD521CDZ AD521SDZ
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Package 14-CDIP (0.300 in, 7.62 mm pitch) 14-CDIP (0.300 in, 7.62 mm pitch) 14-CDIP (0.300 in, 7.62 mm pitch) 14-CDIP (0.300 in, 7.62 mm pitch) 14-CDIP (0.300 in, 7.62 mm pitch) 14-CDIP (0.300 in, 7.62 mm pitch)
Device Type Monolithic instrumentation amplifier Monolithic instrumentation amplifier Monolithic instrumentation amplifier Monolithic instrumentation amplifier Monolithic instrumentation amplifier Monolithic instrumentation amplifier
Amplifier Circuits 1 circuit 1 circuit 1 circuit 1 circuit 1 circuit 1 circuit
Programmable Gain Up to 1000:1 Up to 1000:1 Up to 1000:1 Up to 1000:1 Up to 1000:1 Up to 1000:1

Diferenciadores clave

  • Lower-drift L-grade selection within the AD521 family (frente a AD521KDZ)
  • High common-mode rejection for differential measurements (frente a AD521JDZ)
  • Extended-temperature family path when environmental requirements exceed the L-grade range (frente a AD521SDZ)
  • Through-hole 14-CDIP footprint supports maintainable legacy instrumentation (frente a AD521JDZ)

Notas de diseño

Route the two differential inputs as a closely coupled pair and keep them away from switching-regulator outputs, relay contacts, motor phases, and high-current return paths. Connect the analog ground reference to the measurement system rather than allowing large ground-potential differences to develop across the input source. The manufacturer's pin-configuration and grounding guidance should be followed when assigning the 14-CDIP connections.

Programmable gain increases small-signal bandwidth but can also raise output noise and reduce usable output range. Select the lowest gain that provides the required signal span, check that the expected input and common-mode voltages remain within their limits, and confirm settling time at the selected gain before using the output in a precision acquisition system. Input shielding or guarding may be needed when source impedance is high.

Estimated: with a 12 V supply, a 5 V output, and a 10 mA load, the AD521LDZ would dissipate approximately 70 mW using P = (VIN − VOUT) × IOUT. This estimate does not include internal gain-control or bias-current effects. Keep the device within its 0°C to +70°C operating range and provide normal airflow around the 14-CDIP if surrounding circuitry raises the local ambient temperature.

Do not treat equal package dimensions as proof of exact electrical equivalence. The AD521LDZ is distinguished by its L-grade low-drift and high-linearity position, and substitution can alter input bias, offset, gain error, settling, and temperature behavior. Before replacing it with another AD521 grade, compare those parameters in the manufacturer data sheet and verify the power-on state of every gain-control input.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

No definitive RoHS, REACH, lead-free, halogen-free, or conflict-minerals status was identified. AEC-Q100 is not applicable because this is a general-purpose instrumentation amplifier rather than an automotive-qualified device.

Búsquedas relacionadas

AD521LDZ datasheet AD521LDZ pinout AD521LDZ datasheet pdf Analog Devices AD521LDZ AD521LDZ 14-CDIP pinout AD521LDZ programmable gain 1000 AD521LDZ instrumentation amplifier AD521LDZ equivalent AD521LDZ replacement AD521LDZ vs AD521KDZ AD521LDZ price AD521LDZ stock

Componentes & términos relacionados

Analog Devices AD521LDZ AD521KDZ AD521JDZ AD521BDZ AD521CDZ AD521SDZ instrumentation amplifier differential amplifier analog amplifier precision measurement programmable gain common-mode rejection ratio CMRR input drift slew rate 14-CDIP ceramic dual-inline package through-hole package bridge sensor load cell biomedical instrumentation industrial data acquisition current-loop sensing
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ