ADM4851ARZ - 500 kbps Half-Duplex RS-485 Transceiver | Analog Devices
N.º de pieza: ADM4851ARZ ✓ ActivoADM4851ARZ Descripción general
An RS-485 transceiver is an interface IC that converts between logic-level signals and balanced differential line signals. RS-485 belongs to the EIA-485 family of balanced digital communication standards and is widely used for robust, multidrop industrial data buses. The broader hierarchy is transceiver IC, line interface, communication interface, and signal-conditioning semiconductor. Compared with single-ended communication, balanced differential signaling improves noise immunity and permits reliable data transmission over longer cable runs in electrically noisy environments.
The ADM4851ARZ combines a 5 V supply requirement, a maximum indicated data rate of 500 kbps, and half-duplex operation in an 8-SOIC package. Its differential architecture supports the receiver and driver functions required for RS-485 and RS-422 networks. Slew-rate limiting is an important characteristic because controlled transition rates reduce unwanted harmonics and improve compatibility with balanced communication networks. The compact surface-mount package also supports space-constrained industrial, instrumentation, and embedded-control equipment.
The ADM4851 family is designed for high-speed half-duplex and full-duplex data communication on multipoint bus transmission lines. Although individual family members differ in enable-control arrangements and operating modes, the ADM4851ARZ is specifically identified as the half-duplex version. Its bus interface provides the physical layer needed to connect a microcontroller, programmable controller, or other digital controller to an RS-485 network. Firmware must manage bus direction so that only one transmitter drives the pair at a time.
Typical uses include industrial process-control links, factory automation equipment, building-control systems, instrumentation networks, and embedded serial buses. The 500 kbps capability is appropriate for moderate-speed control and monitoring traffic, while the 8-SOIC package simplifies board construction in equipment using surface-mount assembly. A transceiver such as the ADM4851ARZ can also form part of gateway equipment that converts a local controller interface into a longer-distance differential bus.
Board design should preserve the differential signal path from the transceiver pins through protection components to the connector. Place the receiver and driver interface components close to the device, keep the logic-side traces short, and route the differential pair together with consistent spacing. External protection may be required when the connected cable is exposed to electrostatic discharge, surge events, or industrial transients; the appropriate protection network should be selected from the application voltage and installation environment.
This product page combines manufacturer device information, package and interface details, lifecycle status, practical bus-layout guidance, and a structured comparison with same-package alternatives. It also distinguishes true pin-compatible replacements from functionally similar parts that may use different enable controls or operating modes, helping engineers narrow a replacement search before changing a PCB.
Alternativas directas para ADM4851ARZ — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con ADM4851ARZ (mismo factor de forma y huella) — difiere en Package, Supply Voltage, Signal Type, Supported Standards.
ADM4850ARZ
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →ADM4852ARZ
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
ADM4853ARZ
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
TJA1057GTK/3Z
✅ Sustitución directaConsulte el precio
Ver hoja de datos →MC3486NSR
✅ Sustitución directaConsulte el precio
Ver hoja de datos →ADM4851ARZ Especificaciones
| Product Type | RS-485/RS-422 differential line transceiver |
| Tensión de alimentación | 5 V |
| Maximum Data Rate | 500 kbps |
| Duplex Mode | Half-duplex |
| Supported Standards | EIA RS-485 and EIA RS-422 |
| Driver Configuration | 1/1 transceiver |
| Slew Rate | Limited |
| Signal Type | Balanced differential |
| Encapsulado | 8-pin SOIC |
| Tipo de montaje | Surface mount |
| Estado RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
Configuración de pines de ADM4851ARZ
| Pin 1 | RO — Receiver output |
| Pin 2 | /RE — Receiver enable input, active low |
| Pin 3 | DE — Driver enable input |
| Pin 4 | DI — Driver data input |
| Pin 5 | GND — Ground |
| Pin 6 | Y — Noninverting driver output and noninverting receiver input |
| Pin 7 | A — Inverting driver output and inverting receiver input |
| Pin 8 | VCC — Positive supply |
Aplicaciones típicas
ADM4851ARZ es adecuado para 6 aplicacións: Industrial Process-Control Networks, Factory Automation and PLC Interfaces, Building Control and HVAC Equipment, Test and Measurement Instrumentation, Building and Industrial Gateways, Embedded Environmental Monitoring.
Industrial Process-Control Networks
The ADM4851ARZ fits industrial process-control equipment that must communicate over a balanced RS-485 bus at rates up to 500 kbps. Its 5 V operation aligns with conventional controller logic, while the half-duplex 8-SOIC implementation permits a compact multi-drop field-bus interface. Connect the differential A and Y pair to the bus through protection components rated for the installation environment. Firmware should enable the transmitter only while sending because two active drivers on the same bus can cause contention. The 500 kbps rate supports moderate-speed monitoring and control traffic without requiring a higher-bandwidth physical layer.
Recomendado
Factory Automation and PLC Interfaces
The ADM4851ARZ can provide the physical-layer interface between a PLC peripheral, data concentrator, and factory equipment using an RS-485 bus. Its 500 kbps maximum data rate is suitable for command, status, and sensor traffic, while the balanced differential interface helps reject common-mode noise present near motors and switching equipment. The 8-SOIC package supports compact surface-mount controller boards. Designers should place the transceiver close to the connector, add surge or ESD protection as required, and use the manufacturer application guidance when selecting termination and biasing components for the bus topology.
Recomendado
Building Control and HVAC Equipment
The ADM4851ARZ is appropriate for building-control units, HVAC controllers, and supervisory panels that exchange low-bandwidth configuration and status data over an RS-485 network. A 500 kbps half-duplex channel provides ample margin for typical control traffic, and the 5 V interface can operate alongside conventional embedded-control circuitry. The differential connection supports balanced routing through building wiring while reducing susceptibility to common electrical noise. Select the device when firmware can control bus direction and place protection at the external connector so electrostatic-discharge and transient events do not reach the transceiver pins.
Recomendado
Test and Measurement Instrumentation
The ADM4851ARZ can serve as the communication interface in laboratory and field-test equipment that distributes measurement commands or collects results over RS-485. Its maximum 500 kbps rate supports moderate-volume control data, and the half-duplex architecture limits the bus to one active transmitter at a time. Balanced signaling is useful when instrument systems include long interconnects or uneven grounding. Keep analog and sensitive measurement circuitry physically separated from the cable connector, provide local decoupling, and verify the transceiver's exact common-mode and output-current limits against the chosen cable and termination network.
Recomendado
Building and Industrial Gateways
The ADM4851ARZ is useful in gateways that collect local sensor information and forward it through a long-distance RS-485 link. Its 5 V supply and 8-SOIC footprint simplify integration into compact embedded boards, while the 500 kbps rate supports aggregated telemetry and command traffic. The half-duplex interface avoids requiring separate driver and receiver packages when only one bus direction is active at a time. Use the transceiver's slew-rate-limited outputs to support the balanced network, route A and Y as a pair, and install surge protection at any externally accessible terminal.
Recomendado
Embedded Environmental Monitoring
The ADM4851ARZ can connect distributed environmental-monitoring nodes to a central controller over a balanced RS-485 bus. A 500 kbps half-duplex channel is sufficient for periodic temperature, humidity, air-quality, or equipment-status measurements, while the differential interface improves robustness in installations with variable grounding and electrically noisy loads. The small 8-SOIC package leaves board area for sensing and processing circuitry. Configure the node address at the system level, ensure only one transmitter is enabled, and protect externally exposed wiring with appropriately rated transient and ESD components.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para ADM4851ARZ — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | ADM4850ARZ | ADM4852ARZ | ADM4853ARZ | TJA1057GTK/3Z | MC3486NSR |
|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | NXP Semiconductors | onsemi |
| Product Function | RS-485/RS-422 differential transceiver | RS-485/RS-422 differential transceiver | RS-485/RS-422 differential transceiver | RS-485/RS-422 differential transceiver | RS-485 transceiver | RS-485 transceiver |
Diferenciadores clave
- Defined 500 kbps half-duplex interface (frente a ADM4850ARZ)
- Same 8-SOIC footprint as the ADI ADM485x family (frente a ADM4852ARZ)
- Cross-brand replacement path in the same package class (frente a TJA1057GTK/3Z)
- Available alternative from onsemi (frente a MC3486NSR)
Notas de diseño
Route the A and Y bus conductors as a differential pair with uniform spacing and controlled impedance. Keep the transceiver close to the cable-side protection network, and avoid crossing the pair with unrelated high-current or high-speed logic. Logic-side RO, DI, DE, and /RE traces should remain short and be referenced to the device ground. Follow the Analog Devices application guidance for capacitor placement and bus termination.
Firmware must not enable the driver while another node is transmitting. The ADM4851ARZ is a half-duplex 1/1 transceiver, so the DE and /RE controls should be sequenced to avoid bus contention. Review the exact truth table in the manufacturer datasheet, especially around startup, shutdown, and bus turnaround. A physical RC delay or logic-control solution may be appropriate when the controller resets.
Do not assume that an 8-SOIC package match proves that two RS-485 transceivers are interchangeable. Compare enable polarity, shutdown behavior, receiver fail-safe state, common-mode range, driver current, and data-rate limits before substituting a part. The ADM4851ARZ requires a 5 V supply and supports communication up to 500 kbps; those constraints should form the first screening stage for any replacement.
Place ESD and surge-protection components at the external connector rather than deep inside the enclosure. Select protection that is compatible with the RS-485 common-mode operating range and the required standoff voltage. Maintain a continuous return path for the balanced pair, use the network's intended termination arrangement, and avoid excessive stub lengths that could create reflections at the supported 500 kbps data rate.
Información de cumplimiento
No definitive RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was available for the exact ADM4851ARZ ordering code. The part is an industrial interface IC rather than an AEC-Q100 automotive-qualified device.