Analog Devices

ADM489ARU - 250 kbps Full-Duplex RS-485 | Analog Devices

N.º de pieza: ADM489ARU ✓ Activo
Single +12 V Vdss EIA RS-485 and RS-422 Rds(on) 16-pin TSSOP Package
MOQ: 1 |

ADM489ARU Descripción general

The Analog Devices ADM489ARU is a low-power, full-duplex differential line transceiver designed for RS-485 and RS-422 communications. It supports data rates up to 250 kbps, operates from a single +12 V supply, and provides a bus common-mode range of ±12 V. The device is packaged in a 16-pin TSSOP package. Its slew-rate-limited drivers reduce unwanted line transients, while the receiver provides a 12 kΩ input impedance and 2 kV EFT protection.

A differential line transceiver is the physical-layer interface between digital logic and a balanced communication bus. The ADM489 belongs to the RS-485 and RS-422 transceiver hierarchy within interface ICs, combining a differential driver, differential receiver, and bus protection in one device. Balanced signaling improves noise immunity in industrial environments, while separate transmit and receive paths allow continuous full-duplex communication when the bus architecture supports independently routed pairs.

The principal features include compliance with EIA RS-485 and RS-422 requirements, a maximum data rate of 250 kbps, and operation from a single +12 V supply. The ±12 V common-mode range supports systems where the bus voltage can move relative to the receiver reference. A 12 kΩ receiver input impedance reduces loading on terminated networks, and the 2 kV EFT rating improves robustness in electrically noisy industrial installations.

The slew-rate-limited transmitter is particularly important in RS-485 networks because it reduces the amplitude and duration of edge-related transients on the cable. Unlike a high-speed edge-focused data interface, this controlled transition approach prioritizes dependable multipoint-bus operation over maximum data throughput. The ADM489 includes separate driver-enable and receiver-enable controls, allowing the host logic to manage bus direction and receive state.

Typical applications include industrial process-control networks, factory automation equipment, building-control systems, instrumentation links, and other balanced serial buses operating at moderate speed. Full-duplex operation is particularly useful when transmit and receive pairs are routed independently. The part can also support point-to-point RS-422 links where both ends communicate simultaneously and the transmitter can be disabled when the bus is idle.

Designers should use the manufacturer's pin-description and application guidance when assigning termination, biasing, and protection components. The bus requires correct differential routing, controlled impedance where applicable, and a termination strategy matched to the cable topology. Keep sensitive analog and digital grounds connected according to the recommended layout, and verify that system common-mode voltage remains within the ±12 V bus range.

This product page combines manufacturer specifications, package information, interface-design guidance, application fit, and verified replacement references. It is intended to help engineers evaluate the ADM489ARU for low-power full-duplex RS-485 and RS-422 designs while distinguishing electrical equivalence from changes that affect assembly, qualification, or sourcing.

Alternativas directas para ADM489ARU — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

ADM489ARU-REEL

✅ Sustitución directa
📦 TSSOP-16
Same ADM489 250 kbps electrical ratings with 0% documented data-rate difference; ordering suffix changes reel shipping configuration

📋 Alternativa de referencia (no en el catálogo)

ADM489ARUZ-REEL7

✅ Sustitución directa
📦 TSSOP-16
Same ADM489 250 kbps full-duplex interface with 0% documented data-rate difference; ordering suffix changes reel and qualification configuration

📋 Alternativa de referencia (no en el catálogo)

ADM489ARU Especificaciones

Product Type Full-duplex differential line transceiver
Supported Standards EIA RS-485 and RS-422
Maximum Data Rate 250 kbps
Tensión de alimentación Single +12 V
Bus Common-Mode Range ±12 V
Receiver Input Impedance 12 kΩ
EFT Protection 2 kV
EFT Compliance IEC 1000-4-4
Driver Configuration Slew-rate-limited differential driver
Communication Mode Full-duplex
Power Class Low-power
Encapsulado 16-pin TSSOP
Tipo de montaje Surface mount
Application Environment Multipoint bus transmission lines

Guía de configuración de pines de ADM489ARU 16-pin tssop

Configuración de pines para ADM489ARU (encapsulado 16-pin tssop). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.

Diagrama de patillaje del encapsulado 16-pin tssop para ADM489ARU

No hay datos detallados de patillaje disponibles para ADM489ARU.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

ADM489ARU es adecuado para 6 aplicacións: Industrial Process-Control Networks, Factory Automation Equipment, Building-Control and HVAC Systems, Point-to-Point RS-422 Links, Instrumentation and Sensor Networks, Robust Communications in Noisy Equipment.

🏭

Industrial Process-Control Networks

The ADM489ARU fits moderate-speed industrial process-control links because it supports 250 kbps RS-485 and RS-422 operation, a ±12 V bus common-mode range, and 2 kV EFT protection. Place the transceiver between the controller logic and a balanced field bus, using separate transmit and receive pairs for full-duplex communication. Its slew-rate-limited driver reduces high-energy edge transients on industrial wiring, while the 12 kΩ receiver input impedance limits bus loading. Designers should still verify cable length, topology, grounding, and protection requirements against the Analog Devices ADM488/ADM489 datasheet.

🏭

Factory Automation Equipment

The ADM489ARU is appropriate for factory automation modules that exchange low- to moderate-speed commands and sensor data over a balanced bus. Its 250 kbps maximum rate is sufficient for many machine-control and monitoring networks, while full-duplex operation permits simultaneous transmission and reception when independently routed differential pairs are available. The single +12 V supply simplifies power architecture, and the 2 kV EFT protection rating improves tolerance to industrial transients. Place the device near the connector and bus entry point so surge and ESD protection can be coordinated with the balanced routing.

🧩

Building-Control and HVAC Systems

The ADM489ARU can connect building-control equipment using balanced RS-485 or RS-422 links when the required data rate is 250 kbps or lower. Full-duplex communication supports simultaneous command transmission and status reporting where four-wire bus wiring is available. The ±12 V common-mode range provides tolerance for bus-level voltage variation, while slew-rate limiting helps maintain signal integrity on longer indoor cable runs. For HVAC controllers and distributed sensors, place protection components at the external connector and keep transceiver routing away from switching-power and motor-control nodes.

📡

Point-to-Point RS-422 Links

The ADM489ARU supports point-to-point RS-422 links where both endpoints transmit and receive simultaneously over separate differential pairs. Its 250 kbps data rate covers instrumentation, embedded-control, and remote I/O connections that do not require packet-oriented high-speed Ethernet. The differential receiver has a 12 kΩ input impedance, and the transmitter uses slew-rate limiting to moderate cable-edge transients. The design must control the bus common-mode voltage within ±12 V and use termination consistent with the receiver location and cable topology.

🌐

Instrumentation and Sensor Networks

The ADM489ARU is suitable for instrumentation networks that carry commands, configuration data, and status information below 250 kbps. Balanced differential signaling reduces susceptibility to common-mode noise, while the receiver's 12 kΩ input impedance helps preserve signal integrity on branched or multi-node installations. The low-power, single +12 V design can simplify isolated and embedded acquisition systems. Engineers should use twisted-pair routing, maintain a continuous ground reference where appropriate, and verify that cable loss and termination remain acceptable at the selected communication rate.

🛡️

Robust Communications in Noisy Equipment

The ADM489ARU is useful in equipment where electrical transients could disturb a communication link but the required throughput is only 250 kbps. Its 2 kV EFT protection and IEC 1000-4-4 qualification criterion support more robust industrial operation than an unprotected logic-level interface. The slew-rate-limited driver reduces rapid edge transitions on the cable, and the ±12 V common-mode range permits operation across a wider bus voltage span. Maintain short ground connections and place any additional surge-protection network at the connector rather than scattering it along the internal board.

What is the ADM489ARU?
The ADM489ARU is a low-power, full-duplex differential line transceiver for balanced RS-485 and RS-422 communication links. According to the Analog Devices ADM488/ADM489 datasheet, it combines a slew-rate-limited differential driver with a differential receiver in a 16-pin TSSOP package. The device supports balanced data transmission on multipoint bus lines and can operate from a single +12 V supply.
What are the key specifications of ADM489ARU that engineers should know?
The ADM489ARU supports a maximum data rate of 250 kbps, operates from a single +12 V supply, and tolerates a bus common-mode range of ±12 V. The receiver input impedance is 12 kΩ, and the transmitter includes slew-rate limiting. The Analog Devices datasheet also identifies 2 kV EFT protection and IEC 1000-4-4 compliance as important industrial robustness characteristics.
What is the maximum data rate of ADM489ARU?
The ADM489ARU supports data rates up to 250 kbps. This rate makes the device suitable for moderate-speed balanced serial links rather than high-speed Ethernet or other multi-gigabit interfaces. According to the Analog Devices ADM488/ADM489 datasheet, its slew-rate-limited driver helps control edge transients while supporting reliable RS-485 and RS-422 communication.
What supply voltage does ADM489ARU require?
The ADM489ARU operates from a single +12 V supply. The Analog Devices ADM488/ADM489 datasheet describes the device as a low-power RS-485 and RS-422 transceiver intended for balanced differential links. Designers should use the datasheet power-supply recommendations and place bypass capacitance close to the device according to the published application guidance.
Where to download the ADM489ARU datasheet PDF?
The official ADM489ARU datasheet PDF is available from Analog Devices at https://www.analog.com/media/en/technical-documentation/data-sheets/ADM488_489.pdf. It covers the ADM488 and ADM489 family, including electrical characteristics, driver and receiver behavior, bus loading, protection, pin descriptions, and application information. Use the manufacturer's document for design sign-off and the latest revision status.
Where can I find the ADM489ARU pinout?
The ADM489ARU pinout is shown in the pin-description table of the Analog Devices ADM488/ADM489 datasheet. Because the part uses a 16-pin TSSOP package, every physical pin must be checked against that table before PCB routing or replacement qualification. In particular, verify driver-enable, receiver-enable, supply, ground, and differential I/O assignments rather than inferring them from another RS-485 transceiver.
Is ADM489ARU suitable for industrial RS-485 networks?
Yes, the ADM489ARU is suitable for industrial and commercial balanced communication links that operate below 250 kbps. Its ±12 V bus common-mode range, 12 kΩ receiver input impedance, 2 kV EFT protection, and IEC 1000-4-4 compliance support use in electrically noisy environments. The Analog Devices datasheet specifically describes the family for multipoint bus transmission lines.
Can ADM489ARU be used for full-duplex RS-422 communication?
Yes, the ADM489ARU supports full-duplex RS-422 communication using separate differential transmit and receive paths. The Analog Devices ADM488/ADM489 datasheet identifies compliance with both RS-485 and RS-422 requirements. For full-duplex operation, route separate conductor pairs and manage the driver-enable and receiver-enable controls so the bus is not driven when it should remain idle.
What can replace the ADM489ARU?
The closest documented replacements are ADM489ARU-REEL and ADM489ARUZ-REEL7, both identified in the manufacturer-family documentation search. They use the same 16-pin TSSOP device family and preserve the 250 kbps RS-485/RS-422 interface function. Check the exact ordering suffix, reel configuration, qualification requirements, and current operating limits before approving a substitution.
Is ADM489ARU-REEL the same as ADM489ARU?
ADM489ARU-REEL is the reel-ordering form associated with the ADM489ARU device rather than a different transceiver function. It remains an Analog Devices ADM489-family, 250 kbps, full-duplex RS-485/RS-422 interface in a 16-pin TSSOP package. Confirm the manufacturer ordering table and your assembly requirements to ensure that the exact suffix and shipping format are correct.
Is ADM489ARU the same as ADM489ARUZ-REEL7?
ADM489ARUZ-REEL7 belongs to the ADM489 full-duplex RS-485/RS-485 transceiver family and preserves the same core interface ratings, including 250 kbps operation and a 16-pin TSSOP package. The ordering suffix indicates a specific lead-free or packaging configuration that should be checked against production requirements. It is electrically positioned as a direct family replacement for ADM489ARU.
When should I choose ADM489ARU over ADM488?
Choose ADM489ARU when the design requires a full-duplex RS-485 or RS-422 link with independently operating transmit and receive paths. The ADM489 family supports 250 kbps operation, slew-rate-limited signaling, and a ±12 V common-mode range. An ADM488-family solution may be appropriate for a half-duplex topology, but it should not be treated as an automatic full-duplex replacement without checking pin functions and bus wiring.
What is the best cross-brand equivalent for ADM489ARU?
No cross-brand drop-in replacement can be confirmed from the documented manufacturer and comparison results for the ADM489ARU. A valid replacement must match the 16-pin TSSOP footprint, 250 kbps class, full-duplex architecture, enable controls, supply arrangement, and protection characteristics. Use the Request a Quote form on this page for current sourcing support, and validate any proposed substitute against the ADM488/ADM489 datasheet.
Where to buy ADM489ARU online?
Use the Request a Quote form on this page to request the ADM489ARU and confirm current commercial terms, stock status, quantity requirements, and lead time. The form is the appropriate channel for a changing electronic-component transaction rather than relying on a static listing. Provide the exact ADM489ARU suffix and required reel or tray format when requesting the quotation.
What is the price of ADM489ARU?
The current ADM489ARU price is not stated as a fixed value on this page because electronic-component pricing can change with quantity, availability, and configuration. Use the Request a Quote form on this page to request current pricing for the exact ADM489ARU ordering code. Include your annual demand, target quantities, and packaging requirement so the quotation reflects the intended assembly schedule.
What is the lead time and stock status for ADM489ARU?
The current stock status and production lead time should be confirmed through the Request a Quote form on this page because neither should be inferred from a historical product-page listing. Include the exact ADM489ARU suffix, required quantity, delivery location, and target schedule. A direct manufacturer-channel confirmation will establish allocation and lead time for the particular order.
How should termination and protection be designed for ADM489ARU?
Apply termination according to the physical bus topology rather than placing it indiscriminately on every node. The Analog Devices ADM488/ADM489 datasheet provides the transceiver characteristics and protection guidance needed to evaluate common-mode voltage, cable loading, and surge exposure. Keep the differential pair routed as a pair and use appropriate surge protection when the installation environment requires it.

Datos de referencia de ingeniería para ADM489ARU — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose ADM489ARU when the design requires a low-power, full-duplex RS-485 or RS-422 interface operating at up to 250 kbps from a single +12 V supply. Its ±12 V common-mode range, 12 kΩ receiver input impedance, slew-rate-limited driver, and 2 kV EFT protection make it appropriate for industrial balanced links. Select ADM489ARU-REEL when the assembly process requires that ordering and shipping form while retaining the same core device function. Select ADM489ARUZ-REEL7 when its lead-free ordering configuration matches production requirements, after checking the exact ordering table and qualification expectations. No cross-brand substitute should be approved solely from package similarity: verify the 16-pin TSSOP footprint, enable logic, receiver polarity, electrical limits, protection rating, and full-duplex bus architecture. Use the Request a Quote form for current commercial terms and exact-suffix availability.

Comparación con alternativas

Parámetro Este producto ADM489ARU-REEL ADM489ARUZ-REEL7
Brand Analog Devices Analog Devices Analog Devices
Package TSSOP-16 TSSOP-16 TSSOP-16
Product Type Full-duplex differential line transceiver Full-duplex differential line transceiver Full-duplex differential line transceiver
Supported Standards EIA RS-485 and RS-422 EIA RS-485 and RS-422 EIA RS-485 and RS-422
Maximum Data Rate 250 kbps 250 kbps 250 kbps
Supply Voltage Single +12 V Single +12 V Single +12 V
Bus Common-Mode Range ±12 V ±12 V ±12 V
EFT Protection 2 kV 2 kV 2 kV
Receiver Input Impedance 12 kΩ 12 kΩ 12 kΩ
EFT Compliance IEC 1000-4-4 IEC 1000-4-4 IEC 1000-4-4

Diferenciadores clave

  • Direct ADM489-family ordering compatibility (frente a ADM489ARU-REEL)
  • Lead-free-oriented ordering option (frente a ADM489ARUZ-REEL7)
  • Industrial transient protection (frente a ADM489ARU-REEL)

Notas de diseño

Route each differential pair as a tightly coupled pair with continuous reference-plane support and avoid splitting the pair around unrelated circuitry. Place the transceiver close to the external connector and place termination and surge-protection components near the cable entry. This arrangement minimizes the unprotected cable segment, reduces return-path discontinuities, and keeps common-mode transients away from sensitive logic.

Do not assume that matching the 16-pin TSSOP footprint is sufficient for an unqualified replacement. Verify driver-enable and receiver-enable behavior, supply voltage, common-mode limits, receiver polarity, and bus topology against the ADM488/ADM489 datasheet. In addition, confirm that only the intended driver is active during transmission so that full-duplex wiring cannot produce bus contention.

Apply termination only where the bus topology requires it, normally at the physical ends of a transmission line, and account for the parallel receiver loading when selecting resistor values. Keep the data rate at or below 250 kbps and use twisted-pair cabling. The slew-rate-limited driver reduces edge transients, but correct topology and controlled impedance remain necessary for reliable operation over the installed cable length.

Use the ADM489ARU's 2 kV EFT capability as one part of the industrial-noise strategy rather than the only protection. Add appropriately rated surge and ESD protection at exposed connectors when required by the installation class, and maintain a low-impedance ground reference between the transceiver and protection network. Separate the bus route from motor, relay, and switching-power return currents to prevent common-mode noise from entering the communication path.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The manufacturer-family data identifies EIA RS-485, EIA RS-422, and IEC 1000-4-4 compliance. RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status require confirmation for the exact ordering suffix.

Datos verificados el: 2026-11-09 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

ADM489ARU datasheet ADM489ARU pinout ADM489ARU datasheet pdf ADM489ARU specifications ADM489ARU replacement ADM489ARU equivalent ADM489ARU cross reference ADM489ARU 250 kbps RS-485 ADM489ARU TSSOP-16 ADM489ARU vs ADM488 ADM489ARU industrial bus ADM489ARU price ADM489ARU stock Analog Devices ADM489ARU

Componentes & términos relacionados

Analog Devices ADM489ARU ADM489ARU-REEL ADM489ARUZ-REEL7 ADM488 ADM489 RS-485 RS-422 EIA RS-485 EIA RS-422 differential line transceiver interface IC full-duplex communication multipoint bus slew rate common-mode range receiver input impedance EFT protection IEC 1000-4-4 TSSOP-16 surface mount industrial automation building control instrumentation network
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ