ADS1286UC - 12-Bit 20 kHz Micro-Power ADC | Texas Instruments
N.º de pieza: ADS1286UC ✓ ActivoADS1286UC Descripción general
An analog-to-digital converter, or ADC, converts an analog voltage into a numeric code for processing, measurement, logging, or control. Within the semiconductor hierarchy, the ADS1286 belongs to the ADC category, uses a successive-approximation architecture, and includes a sample-and-hold front end. Its differential input can measure the voltage between two input nodes, which is useful when the source has a nonzero ground reference or common-mode voltage.
The ADS1286 supports sampling at 20 kHz while resolving 12-bit data. Its serial interface is compatible with SPI and SSI protocols and can operate over a two-wire or three-wire connection. The 250 uA supply current supports remote and battery-influenced instrumentation, while the integrated sample-and-hold amplifier reduces the external signal-conditioning required for many low-frequency analog measurements.
The ADS1286UC uses a successive-approximation conversion architecture and a single differential input. Its operating range is -40 °C to +85 °C, and the 8-pin SOIC package supports surface-mount assembly. The 4.5 V to 5.25 V supply requirement places it in conventional 5 V analog systems, where careful reference grounding and input filtering remain important for stable conversion performance.
Typical uses include industrial process measurement, battery-powered environmental sensors, portable medical instrumentation, low-level pressure monitoring, and embedded data-acquisition systems. The serial interface also allows the converter to connect directly to a microcontroller while reducing the number of external signal lines.
For reliable operation, decouple the supply close to the device, connect the analog and digital return paths carefully, and use the reference and differential-input pins according to the manufacturer pin-description table. A common-mode voltage outside the input range can impair conversion accuracy even when the differential signal itself is within range.
This page combines manufacturer specifications, same-footprint ordering options, application guidance, and design notes to support component selection and PCB implementation. It also distinguishes verified drop-in options from broader functional ADC substitutions that may require different footprints, interfaces, or software support.
Alternativas directas para ADS1286UC — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con ADS1286UC (mismo factor de forma y huella) — difiere en Architecture, Package, Input Type, Resolution, Missing Codes.
ADS1286UB
✅ Sustitución directaConsulte el precio
Ver hoja de datos →ADS1286U/2K5G4
✅ Sustitución directaConsulte el precio
Ver hoja de datos →ADS1286U
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →ADS1286UC Valores máximos y características eléctricas
| Resolución | 12 bit |
| Frecuencia de muestreo | 20 kHz |
| Architecture | Successive approximation (SAR) |
| Input Type | Differential |
| Number of Input Channels | 1 |
| Supply Voltage Range | 4.5 V to 5.25 V |
| Corriente de alimentación | 250 uA |
| Analog Front End | Integrated sample-and-hold amplifier |
| Digital Interface | SPI and SSI compatible serial interface |
| Interface Wiring | Two-wire or three-wire serial interface |
| Rango de temperatura de funcionamiento | -40 °C to +85 °C |
| Temperature Grade | Industrial |
| Encapsulado | 8-pin SOIC |
| Tipo de montaje | Surface mount |
| Terminal Form | Gull wing |
Guía de configuración de pines de ADS1286UC 8-pin soic
Configuración de pines para ADS1286UC (encapsulado 8-pin soic). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para ADS1286UC.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
ADS1286UC es adecuado para 6 aplicacións: Industrial Process Measurement, Battery-Powered Environmental Sensors, Portable Medical Instrumentation, Pressure and Level Monitoring, Embedded Data Acquisition, Remote Telemetry.
Industrial Process Measurement
The ADS1286UC fits industrial process measurement because it combines 12-bit resolution, a 20 kHz sampling rate, and a differential input in a compact 8-pin SOIC package. Place the converter at the transmitter end of a low-level sensor interface so that the measured voltage difference can be converted before cable noise and ground offsets add uncertainty. Its 250 uA supply current reduces the burden on remote sensor loops, while the two-wire serial option minimizes host-controller connections. Verify that the process signal, common-mode voltage, and reference remain inside the device limits.
Recomendado
Battery-Powered Environmental Sensors
The ADS1286UC is appropriate for battery-powered environmental sensors that monitor temperature, humidity, pressure, or other slowly changing analog quantities. Its 12-bit resolution provides 4096 digital codes, while the 20 kHz sampling capability is more than sufficient for common low-frequency environmental measurements. The 250 uA supply current helps preserve battery capacity during periodic sampling, and the SPI- or SSI-compatible interface permits efficient connection to a low-power microcontroller. Duty cycle, reference current, and regulator losses should also be included in the final energy calculation.
Recomendado
Portable Medical Instrumentation
The ADS1286UC can support portable medical instrumentation when the required signal bandwidth and accuracy fit a 12-bit, 20 kHz converter. Its differential input is useful for sensor signals that are small or referenced above the instrument ground, while the integrated sample-and-hold amplifier reduces front-end complexity. The compact 8-pin SOIC package leaves board area for the sensor interface and signal conditioning. For diagnostic or patient-connected circuits, complete the appropriate medical risk assessment, isolation design, validation, and regulatory review rather than relying on general component suitability alone.
Recomendado
Pressure and Level Monitoring
The ADS1286UC suits pressure- and level-monitoring systems that use resistive, capacitive, or differential bridge-derived voltages. Its 12-bit resolution and 20 kHz sampling rate can capture dynamic system response while the differential input helps reject signals common to both sensor inputs. The 250 uA supply current is advantageous in remote installations where energy is constrained. Place the converter near the sensor interface, maintain a clean reference, and confirm that the bridge excitation, common-mode voltage, and return paths remain compatible with the 4.5 V to 5.25 V supply range.
Recomendado
Embedded Data Acquisition
The ADS1286UC supports embedded data-acquisition modules requiring compact sampling and a simple serial connection to a microcontroller. A 20 kHz conversion rate is suitable for many control, monitoring, and slow-signal waveform tasks, while the two-wire or three-wire serial interface allows the host to select the wiring arrangement that best fits its available pins. The 8-pin SOIC package simplifies board-area planning, and the 250 uA supply current supports small embedded platforms. Confirm the required data rate, reference accuracy, acquisition timing, and digital interface implementation before finalizing the circuit.
Recomendado
Remote Telemetry
The ADS1286UC is useful in remote telemetry equipment where a sensor signal must be digitized close to its source before transmission. Its differential input accommodates common-mode sensor signals, and the 250 uA operating current is valuable when the node is battery powered or remotely powered. The 12-bit resolution and 20 kHz sampling rate cover many temperature, pressure, and equipment-condition measurements, while the compact serial interface limits wiring overhead. Use local decoupling and careful grounding to prevent reference noise and ground potential differences from degrading the converted result.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para ADS1286UC — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | ADS1286UB | ADS1286U/2K5G4 | ADS1286U |
|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit |
| Sampling Rate | 20 kHz | 20 kHz | 20 kHz | 20 kHz |
| Architecture | Successive approximation (SAR) | Successive approximation (SAR) | Successive approximation (SAR) | Successive approximation (SAR) |
| Input Type | Differential | Differential | Differential | Differential |
| Supply Voltage Range | 4.5 V to 5.25 V | 4.5 V to 5.25 V | 4.5 V to 5.25 V | 4.5 V to 5.25 V |
| Supply Current | 250 uA | 250 uA | 250 uA | 250 uA |
| Digital Interface | SPI and SSI compatible | SPI and SSI compatible | SPI and SSI compatible | SPI and SSI compatible |
Diferenciadores clave
- Low power for a 12-bit SAR converter (frente a ADS1286UB)
- Compact 8-pin integration (frente a ADS1286U/2K5G4)
- Differential measurement in a single-input package (frente a ADS1286U)
Notas de diseño
Place the ADC supply bypass capacitor immediately between the supply and ground pins, and route analog and digital return currents so switching current does not flow through the input-reference path. The ADS1286UC operates from 4.5 V to 5.25 V, so the layout should minimize drops and coupling between the analog front end and the serial interface. Keep the differential-input traces short, matched where practical, and away from clock and switching-node traces.
Confirm the differential input common-mode voltage and full-scale range before applying sensor signals. A differential signal within the input span can still produce inaccurate results if its common-mode component is outside the allowed range. Use the manufacturer input-range diagrams to set scaling, and treat the reference network as part of the measurement chain because reference variation affects the digital result proportionally.
Do not interpret the 20 kHz sampling rate as suitability for every high-frequency waveform. The 12-bit SAR converter is best aligned with low-bandwidth process, sensor, and control signals, where its differential input and low 250 uA supply current provide practical benefits. Use the serial-interface timing diagrams to configure clock polarity, data validity, and conversion timing in the host controller, especially when using the two-wire configuration.
Información de cumplimiento
The industrial-temperature ADS1286UC is not identified as an AEC-Q100 automotive device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer product documentation.