Texas Instruments

ADS8558IPM - 12-Bit 6-Channel 730 kSPS Simultaneous ADC | TI

N.º de pieza: ADS8558IPM ✓ Activo
64-pin LQFP (PM) Package Internal conversion clock supported Speed
MOQ: 1 |

ADS8558IPM Descripción general

The Texas Instruments ADS8558IPM is a 12-bit, six-channel simultaneous-sampling successive approximation register ADC with true bipolar inputs, up to 730 kSPS in parallel interface mode, and a 64-pin LQFP (PM) package measuring 10 mm by 10 mm. It includes one sample-and-hold circuit per channel and supports up to 500 kSPS in serial interface mode.

An ADC is a data-converter integrated circuit that transforms continuous analog voltages into numerical values for processing by a microcontroller, DSP, FPGA, or industrial controller. The ADS8558 belongs to the SAR ADC family, where successive approximation selects the digital result one bit at a time. It sits within the broader hierarchy of analog-to-digital converters, data-converter ICs, and semiconductor components used to acquire real-world signals.

The ADS8558IPM is organized as six SAR conversion channels grouped into three pairs. True bipolar input capability allows each channel to measure voltages that extend below ground, while the sample-and-hold architecture supports simultaneous high-speed acquisition of multiple signals. The 12-bit resolution provides 4096 possible digital codes, while the selectable parallel or serial interface supports different processor architectures and communication priorities.

At the maximum parallel-interface data rate, each of the six channels can convert at 730 kSPS. Serial operation supports data rates up to 500 kSPS and can reduce the number of interface signals required on a constrained printed circuit board. The device also supports an internal conversion clock and reference, according to the manufacturer product information, although exact timing, input range, reference voltage, and electrical limit details should be confirmed in the complete manufacturer datasheet before a new design is released.

Typical signal-acquisition uses include industrial process monitoring, motor and drive control, power-system instrumentation, data acquisition systems, and test equipment requiring several channels to be sampled at the same instant. Simultaneous sampling is particularly useful when comparing phase-related voltages, because the separate sample-and-hold circuits reduce timing differences between channels.

PCB implementation should prioritize short, symmetric analog input routes and a quiet reference and supply arrangement. Place input filtering and protection components close to their associated pins, keep digital interface routing away from sensitive analog nodes, and use a solid ground plane with uninterrupted return paths. The LQFP package also requires careful thermal assessment when operated near its maximum specified ambient temperature.

This product page organizes the key ADC characteristics, package information, application guidance, comparison data, and practical design considerations in one place. Engineers should use the manufacturer pin-description table and recommended application circuit when assigning tracks, selecting external components, and validating acquisition timing.

Alternativas directas para ADS8558IPM — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con ADS8558IPM (mismo factor de forma y huella) — difiere en Operating Temperature Range.

Texas Instruments
Operating Temperature Range: -40°C to +125°C
Comparar con ADS8558IPM →

ADS8557IPM

✅ Sustitución directa ⚠️ Especificaciones sin verificar
Texas Instruments
📦 LQFP-64 (PM)
14 bit · 6 channels · 670 kSPS · Successive approximation register (SAR) · Simultaneous sampling with per-channel sample-and-hold · True bipolar · 730 kSPS · 500 kSPS

Consulte el precio

Ver hoja de datos →

ADS8556IPM

✅ Sustitución directa ⚠️ Especificaciones sin verificar
Texas Instruments
📦 LQFP-64 (PM)
16 bit · 6 channels · Simultaneous sampling · Six SAR ADCs grouped in three pairs · 630 kSPS per channel · 450 kSPS per channel · Parallel and serial · Yes

Consulte el precio

Ver hoja de datos →

ADS8558IPMR

✅ Sustitución directa
📦 LQFP-64 (PM)
Identical 12-bit ADS8558 electrical configuration; packaging format changes from the ADS8558IPM tray orderable code to tape-and-reel

📋 Alternativa de referencia (no en el catálogo)

ADS8558IPM Valores máximos y características eléctricas

Resolución 12 bit
Number of Channels 6 channels
Conversion Architecture Successive approximation register (SAR)
Maximum Data Rate, Parallel Interface 730 kSPS per channel
Maximum Data Rate, Serial Interface 500 kSPS per channel
Input Type True bipolar
Sampling Method Simultaneous sampling
Sample-and-Hold Circuit One per channel
Channel Grouping Six channels grouped into three pairs
Interfaz Parallel or serial
Encapsulado 64-pin LQFP (PM)
Package Dimensions 10 mm x 10 mm
Tipo de montaje Surface mount
Rango de temperatura de funcionamiento -40 °C to +125 °C
Conversion Clock Internal conversion clock supported
Reference Internal reference supported
Power Classification Low-power ADC
Estado RoHS unknown
REACH Status unknown
AEC-Q100 Qualification not_qualified

Guía de configuración de pines de ADS8558IPM 10 mm x 10 mm

Configuración de pines para ADS8558IPM (encapsulado 10 mm x 10 mm). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.

Diagrama de patillaje del encapsulado 10 mm x 10 mm para ADS8558IPM

No hay datos detallados de patillaje disponibles para ADS8558IPM.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

ADS8558IPM es adecuado para 6 aplicacións: Industrial Process Monitoring, Motor and Drive Control, Power-System Instrumentation, Synchronized Data Acquisition, Test and Measurement Equipment, Audio and Vibration Analysis.

🏭

Industrial Process Monitoring

The ADS8558IPM suits industrial process-monitoring systems that must acquire several sensor voltages together. Its six true-bipolar input channels allow each channel to retain a sample-and-hold circuit, supporting simultaneous acquisition at up to 730 kSPS in parallel interface mode. This is useful when pressure, temperature, current, and voltage signals must retain a close timing relationship during a conversion cycle. The 12-bit resolution provides 4096 digital codes, while the parallel or serial interface lets the converter connect to either a high-throughput processor or a controller with fewer interface resources.

⚡

Motor and Drive Control

The ADS8558IPM is appropriate for motor-control systems that monitor multiple phase, current, or position-related voltages. Six simultaneously sampled channels provide a consistent acquisition window, while true bipolar inputs are useful for signals centered around ground. The maximum parallel-interface rate of 730 kSPS supports fast control-loop feedback, and the serial option can operate up to 500 kSPS when interface pin count is more important than throughput. Engineers should preserve analog symmetry and provide appropriate source impedance and filtering for each input.

🔧

Power-System Instrumentation

The ADS8558IPM can capture multiple bipolar voltages in power-system monitoring equipment, including DC-link, phase, and shunt measurements. Simultaneous sampling helps preserve the relationship among measured quantities, while the 12-bit conversion resolution supports compact protection, logging, and diagnostics systems. The device supports up to 730 kSPS in parallel mode for high-speed analysis or up to 500 kSPS in serial mode for lower pin-count implementations. Protection networks, input filtering, and isolation boundaries must be designed around the datasheet electrical limits.

🖥️

Synchronized Data Acquisition

The ADS8558IPM fits synchronized data-acquisition systems requiring six channels to be sampled under the same timing conditions. Each input uses a dedicated sample-and-hold circuit, reducing the need to stagger channel selection in multi-sensor measurement systems. Parallel operation reaches 730 kSPS, while serial operation reaches 500 kSPS and can simplify routing into a processor with constrained I/O. For sensitive instrumentation, use a quiet reference arrangement, maintain short analog traces, and separate converter clocks and digital outputs from high-impedance input nodes.

📺

Test and Measurement Equipment

The ADS8558IPM can form the acquisition front end of programmable test equipment requiring several measured nodes to be captured together. Six true-bipolar channels reduce the number of separate converters required when monitoring a multi-node fixture. A throughput of 730 kSPS in parallel mode can support fast sweeps and repetitive measurements, while the serial interface offers a lower pin-count option for compact instruments. Calibration, source impedance, reference stability, and front-end protection are critical to achieving repeatable results.

🎧

Audio and Vibration Analysis

The ADS8558IPM is applicable to multichannel vibration, acoustic, or condition-monitoring systems where several sensor outputs must be sampled at a common instant. The six-channel SAR architecture supports up to 730 kSPS in parallel mode, providing sufficient temporal resolution for many vibration-analysis tasks, and true bipolar inputs accommodate sensors with centered waveforms. Designers should use anti-alias filtering, shielded input routing, and careful reference grounding because sensor-level signals can be small and the 12-bit resolution is more appropriate than 16-bit alternatives when conversion speed has priority.

What is the ADS8558IPM?
The ADS8558IPM is a 12-bit, six-channel simultaneous-sampling SAR analog-to-digital converter from Texas Instruments. It supports up to 730 kSPS in parallel interface mode, true bipolar inputs, and one sample-and-hold circuit per channel. According to the Texas Instruments ADS8558 product page, the device is packaged in a 64-pin LQFP and operates from -40 °C to +125 °C.
What is the conversion rate of ADS8558IPM?
The ADS8558IPM converts at up to 730 kSPS per channel in parallel interface mode and up to 500 kSPS per channel in serial interface mode. According to the Texas Instruments ADS8558 ordering information, the maximum rate of 730 kSPS applies when the internal conversion clock and reference are used. Serial mode can reduce interface pin count in space-constrained designs.
How many channels does ADS8558IPM have?
The ADS8558IPM has six analog input channels organized into three pairs. Each channel contains its own sample-and-hold circuit, allowing related signals to be captured simultaneously. The Texas Instruments product information describes the ADS855x family as a group of low-power, 16-, 14-, or 12-bit SAR ADCs for high-speed multichannel acquisition.
Does ADS8558IPM support true bipolar input?
Yes, the ADS8558IPM supports true bipolar analog inputs. According to the Texas Instruments ADS8558 product page, its six SAR-based channels can acquire voltages that extend below ground. This capability is useful for bipolar sensor outputs, shunt measurements, and ± voltage interfaces, subject to the input and common-mode limits in the manufacturer datasheet.
What is the difference between ADS8558IPM and ADS8557IPM?
The ADS8558IPM is the 12-bit member, while the ADS8557IPM is the 14-bit member of the pin- and software-compatible ADS855x family. The resolution difference is 2 bits, or approximately 16.7% relative to 12-bit resolution. Both devices provide six simultaneous-sampling channels, but the ADS8557 provides greater numerical resolution for applications where quantization granularity is more important.
What is the difference between ADS8558IPM and ADS8556IPM?
The ADS8558IPM provides 12-bit resolution, while the ADS8556IPM provides 16-bit resolution within the ADS855x family. The 4-bit increase represents approximately 33.3% more resolution bits, allowing the ADS8556 to represent roughly 16 times as many quantization levels. Both use six SAR channels with simultaneous sampling, but the choice depends on resolution, throughput, and system timing requirements.
When should I choose ADS8558IPM over ADS8557IPM?
Choose the ADS8558IPM when 12-bit resolution is sufficient and maximum acquisition speed is the priority. It supports up to 730 kSPS in parallel mode, while the 14-bit ADS8557IPM provides finer quantization. According to the Texas Instruments family description, the devices are pin- and software-compatible, so resolution can influence the choice without requiring a different package.
Is ADS8558IPM suitable for simultaneous data acquisition?
The ADS8558IPM is designed for simultaneous multichannel acquisition because each of its six channels has a separate sample-and-hold circuit. This is advantageous for phase-related measurements in motor control, industrial monitoring, and synchronized instrumentation. The maximum throughput is 730 kSPS per channel in parallel mode, subject to correct clock, reference, and interface timing.
Where can I download the ADS8558IPM datasheet PDF?
The official ADS8558 datasheet and product documentation can be accessed through the Texas Instruments ADS8558 product page at https://www.ti.com/product/ADS8558. Use the manufacturer datasheet for the complete electrical characteristics, pin-description table, register map, timing diagrams, and recommended application circuit before finalizing the PCB design.
Where can I find the ADS8558IPM pinout?
The ADS8558IPM pin assignment is documented in the pin-description table of the Texas Instruments ADS8558 datasheet. The device uses a 64-pin LQFP (PM) package. Assign each analog input, reference, supply, ground, clock, and digital-interface signal strictly according to that table; exposed-pad and thermal-layout details should also follow the manufacturer package drawing.
What are the key specifications engineers should know about ADS8558IPM?
The ADS8558IPM combines 12-bit resolution, six true-bipolar SAR channels, simultaneous sampling, and a 730 kSPS maximum parallel-interface rate. Its serial interface supports up to 500 kSPS, and the operating temperature range is -40 °C to +125 °C. The 64-pin LQFP package is 10 mm by 10 mm. These characteristics make it suitable for synchronized industrial and instrumentation signal acquisition.
Can ADS8558IPM replace ADS8558IPMR?
The ADS8558IPM and ADS8558IPMR identify the same electrical device but use different orderable packaging formats. The comparison identifies ADS8558IPMR as the tape-and-reel form, while ADS8558IPM is the tray form identified in the product ordering information. PCB compatibility is therefore expected, but the assembly-line feed method must be selected before procurement.
What is the best drop-in replacement for ADS8558IPM?
ADS8558IPMR is the closest ordering alternative because it is the same ADS8558 device in a tape-and-reel package, but it does not provide a different electrical substitute. ADS8557IPM and ADS8556IPM are pin- and software-compatible family members with 14-bit and 16-bit resolution, respectively. The ADS8556's 4-bit resolution increase should be reviewed carefully against timing and output-format requirements.
Where can I buy ADS8558IPM online?
The ADS8558IPM can be requested through the Request a Quote form on this XAIPART product page. The form is the appropriate route for current availability, lead time, quantity requirements, and package-format confirmation. Texas Instruments lists the device under the orderable number ADS8558IPM in its 64-pin LQFP PM package.
What is the price of ADS8558IPM?
Current ADS8558IPM pricing and quantity availability should be obtained through the Request a Quote form on this XAIPART product page. The form supports a current commercial response for the exact orderable MPN and tray packaging. Engineers should also confirm lead time, minimum order quantity, and whether the quote is based on one piece or a production quantity.
Is ADS8558IPM in stock and what is its lead time?
Current stock and lead-time status for ADS8558IPM should be confirmed through the Request a Quote form on this XAIPART product page. Submit the required quantity and specify the LQFP PM orderable configuration. The manufacturer product information identifies ADS8558IPM as an active 64-pin LQFP device rated from -40 °C to +125 °C.

Datos de referencia de ingeniería para ADS8558IPM — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose the ADS8558IPM when the design needs the fastest throughput in the ADS855x family and 12-bit resolution is adequate. Its six true-bipolar, simultaneously sampled channels support 730 kSPS in parallel mode or 500 kSPS in serial mode. Select the ADS8557IPM when 14-bit resolution is valuable but the lower 670 kSPS parallel and 470 kSPS serial limits remain acceptable. Select the ADS8556IPM when 16-bit resolution takes priority and the reduced 630 kSPS parallel or 450 kSPS serial throughput is sufficient. Use ADS8558IPMR when the electrical design is unchanged but automated tape-and-reel assembly is required. Confirm interface timing, acquisition mode, external circuitry, and pin-level requirements against the manufacturer datasheet before substituting any family member.

Comparación con alternativas

Parámetro Este producto ADS8557IPM ADS8556IPM ADS8558IPMR
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 64-pin LQFP (PM), 10 mm x 10 mm 64-pin LQFP (PM) 64-pin LQFP (PM) 64-pin LQFP (PM)
Resolution 12 bit 14 bit 16 bit 12 bit
Number of Channels 6 channels 6 channels 6 channels 6 channels
Maximum Data Rate, Parallel Interface 730 kSPS per channel 670 kSPS per channel 630 kSPS per channel 730 kSPS per channel
Maximum Data Rate, Serial Interface 500 kSPS per channel 470 kSPS per channel 450 kSPS per channel 500 kSPS per channel
Input Type True bipolar True bipolar True bipolar True bipolar
Sampling Method Simultaneous sampling Simultaneous sampling Simultaneous sampling Simultaneous sampling
Conversion Architecture SAR SAR SAR SAR
Operating Temperature Range -40 °C to +125 °C -40 °C to +125 °C -40 °C to +125 °C -40 °C to +125 °C

Diferenciadores clave

  • Higher parallel conversion throughput (frente a ADS8557IPM)
  • Maximum family throughput in serial mode (frente a ADS8556IPM)
  • Identical electrical design with alternate reel configuration (frente a ADS8558IPMR)
  • Resolution-versus-speed tradeoff within one family (frente a ADS8556IPM)

Notas de diseño

Route the six analog inputs as short, symmetric traces to minimize input capacitance and channel-to-channel timing differences. Place input filtering, clamping, or protection components close to the ADC pins rather than at the connector. Keep the parallel-output and serial-interface return paths away from the analog inputs, and provide a continuous ground plane beneath and around the LQFP footprint.

Use the interface mode that matches the receiving device and firmware. Parallel mode supports up to 730 kSPS per channel but requires more routing and careful clock-to-data timing; serial mode supports up to 500 kSPS and reduces interface-pin pressure. Verify output timing, level compatibility, and signal termination against the complete manufacturer timing diagrams before selecting the processor interface.

Provide clean supply and reference connections with low-impedance decoupling placed close to the relevant pins. Reference noise can affect conversion accuracy, so avoid routing digital return currents through the analog-reference area. Confirm bypass-capacitor values, allowable supply ranges, startup behavior, and reference-bypass requirements from the manufacturer application circuit before releasing the schematic.

The ADS8558IPM is rated for operation from -40 °C to +125 °C, but the complete design must remain within the device's power and junction-temperature limits. Account for converter dissipation, PCB copper area, adjacent heat sources, and enclosure temperature. The LQFP footprint has leads on all four sides, so assembly inspection is important for detecting solder bridges that could impair thermal and signal performance.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Qualified
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The manufacturer product information identifies ADS8558IPM as operating from -40 °C to +125 °C but does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. The non-automotive orderable code is not identified as AEC-Q100 qualified.

Datos verificados el: 2026-11-18 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

ADS8558IPM ADS8558IPM datasheet ADS8558IPM datasheet pdf ADS8558IPM pinout ADS8558IPM specifications ADS8558IPM equivalent ADS8558IPM replacement ADS8558IPM cross reference ADS8558IPM vs ADS8557IPM ADS8558IPM price ADS8558IPM stock Texas Instruments ADS8558IPM ADS8558IPM LQFP-64 footprint ADS8558IPM application circuit 12-bit 6-channel simultaneous ADC

Componentes & términos relacionados

Texas Instruments ADS8558IPM ADS8557IPM ADS8556IPM ADS8558IPMR ADS855x analog-to-digital converter ADC successive approximation register SAR ADC simultaneous-sampling ADC true bipolar input sample-and-hold circuit parallel interface serial interface internal reference internal conversion clock 12-bit resolution 14-bit resolution 16-bit resolution 730 kSPS 500 kSPS LQFP-64 PM package surface mount industrial process monitoring motor control data acquisition power-system instrumentation test and measurement
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ