AP63301WU-7 - 3A, 32V Sync Buck Converter, TSOT-23-6 | Diodes Inc
N.º de pieza: AP63301WU-7 ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $0.8 | $0,80 |
| 10 | $0.69 | $6,90 |
| 100 | $0.55 | $55,00 |
| 500 | $0.46 | $230,00 |
| 1.000 | $0.4 | $400,00 |
| 3.000 | $0.35 | $1.050,00 |
AP63301WU-7 Descripción general
A synchronous buck converter is a switched-mode power supply topology that uses pulse-width modulation (PWM) to regulate an output voltage lower than its input, while replacing the external Schottky diode with an internal low-side MOSFET for higher efficiency. AP63301WU-7 belongs to the hierarchy: synchronous buck converter -> buck converter -> step-down regulator -> switching regulator -> DC-DC converter -> power management IC -> semiconductor IC. This category is used wherever a board needs a low-voltage rail (e.g., 3.3 V, 5 V, 12 V) generated from a higher-voltage bus (e.g., 12 V, 24 V industrial supplies), with higher efficiency than a linear regulator.
Key differentiating features include an internal high-side 75 mΩ / low-side 40 mΩ MOSFET pair, peak current-mode control with internal compensation, a 1.18 V-typical enable input that can be connected directly to VIN for automatic startup, internal soft-start, and an EMI-optimized gate driver that helps meet CISPR 25 / CISPR 22 conducted-emissions limits without complex filtering. The AP63301WU-7 is the EMI-tuned version of the family, while its sibling AP63300WU-7 adds frequency spread spectrum.
Technically, the device operates at a fixed switching frequency, uses peak current-mode control for fast transient behavior and simple loop compensation, and provides cycle-by-cycle current limit, thermal shutdown, and over-voltage protection. The TSOT-23-6 package with an exposed thermal pad keeps junction-to-ambient resistance low enough for 3 A operation at moderate VIN-VOUT differentials without external heatsinking.
Typical applications include 12 V and 24 V industrial bus point-of-loads, USB-PD / Type-C charging rails, white goods and home appliance power, telecom 5 V/3.3 V auxiliary supplies, and FPGA/MCU core or I/O rails. Compared with linear regulators, AP63301WU-7 dramatically lowers the heat dissipated when stepping 24 V to 5 V at 3 A.
Designers should size the input capacitor for RMS current, select the output inductor for approximately 20-40% ripple, and follow the datasheet feedback-resistor table to program the output between 0.8 V and roughly VIN minus losses. This page synthesizes distributor pricing, drop-in TSOT-23-6 alternatives, and practical design notes not found in the manufacturer datasheet alone.
Alternativas directas para AP63301WU-7 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con AP63301WU-7 (mismo factor de forma y huella) — difiere en Continuous Output Current, Package, Quiescent Current.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
AP63300WU-7
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
AP63205WU-7
✅ Sustitución directa✓ En stock
$0.2036 / unidad
Ver hoja de datos →AP63210WU
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
AP63301WU-7 Valores máximos y características eléctricas
| Topología | Synchronous Buck (Step-Down) |
| Rango de tensión de entrada | 3.8 V to 32 V |
| Rango de tensión de salida | 0.8 V to ~28 V (adjustable) |
| Continuous Output Current | 3 A |
| High-Side MOSFET | 75 mΩ (typ.) |
| Low-Side MOSFET | 40 mΩ (typ.) |
| Corriente en reposo | 280 µA (typ., no load) |
| Control Mode | Peak Current-Mode PWM |
| Feedback Voltage Reference | 0.8 V (typ.) |
| Enable Threshold (Rising) | 1.18 V (typ.) |
| EMI Reduction | EMI-optimized gate driver (no FSS) |
| Arranque suave | Internal |
| Protections | OCP, OVP, UVLO, Thermal Shutdown |
| Temperatura de unión de funcionamiento | -40 °C to +125 °C |
| Encapsulado | TSOT-23-6 (TSOT26) with exposed pad |
| Tipo de montaje | Surface Mount |
| Estado RoHS | Compliant |
Configuración de pines de AP63301WU-7
| Pin 1 | EN — Enable input (active high; tie to VIN for auto-startup; rising threshold typ. 1.18 V) |
| Pin 2 | GND — Power and analog ground return |
| Pin 3 | SW — Switch node - connection point of the internal high-side / low-side MOSFETs and external inductor |
| Pin 4 | VIN — Input supply voltage, 3.8 V to 32 V |
| Pin 5 | BST — Bootstrap pin for high-side gate driver; connect to SW via 100 nF bootstrap capacitor |
| Pin 6 | FB — Feedback input to internal error amplifier; connect to VOUT resistor divider (VREF = 0.8 V typ.) |
Aplicaciones típicas
AP63301WU-7 es adecuado para 6 aplicacións: 24V Industrial Bus Point-of-Load, USB-PD / Type-C Charging Rails, Home Appliance & White Goods Power, Telecom Auxiliary Supplies, FPGA / MCU Power Rails, Automotive Accessory Power (Non-Safety).
24V Industrial Bus Point-of-Load
The AP63301WU-7's 3.8 V to 32 V VIN window directly accepts the 24V industrial bus and steps it down to 3.3V, 5V, or 12V rails without a pre-regulator. With 3 A capability and a 75 mΩ/40 mΩ MOSFET pair, it delivers 3.3V at 3 A from 24V input with roughly 90% efficiency and under 1 W dissipation. Its EMI-optimized gate driver helps meet CISPR 11/22 Class B in PLC, sensor, and motor-drive subsystems without complex input filtering.
Recomendado
USB-PD / Type-C Charging Rails
USB-PD chargers require a buck converter that can take a 5V to 20V bus and produce 5V, 9V, 15V, or 20V outputs at 2 A to 3 A. The AP63301WU-7's 32V VIN tolerance and 3 A IOUT deliver USB-PD 60W capability in a TSOT-23-6 footprint, ideal for compact travel adapters and Type-C docks. The internal compensation and peak current-mode control simplify the loop design, while OVP and OCP safeguard the cable and downstream device.
Recomendado
Home Appliance & White Goods Power
White goods such as washing machines, refrigerators, and dishwashers run from rectified 12V or 24V rails and need 3.3V, 5V, and 12V subsystems at 1 A to 3 A. The AP63301WU-7's TSOT-23-6 package fits small control boards, and its -40 °C to +125 °C junction range handles appliance thermal stress. EMI-optimized switching passes CISPR 14-1 conducted emissions without a complex pi-filter on VIN.
Recomendado
Telecom Auxiliary Supplies
Telecom 48V systems use intermediate 12V or 5V rails for fans, microcontrollers, and housekeeping circuitry. The AP63301WU-7 directly accepts a 24 V to 32 V telecom tap and produces 5 V at 3 A for fans and control logic. Synchronous rectification keeps efficiency high at the 32V-max VIN, while internal OVP/OCP protects downstream ASICs during transient bus events.
Recomendado
FPGA / MCU Power Rails
Modern FPGAs and high-performance MCUs require low-voltage, high-current cores (e.g., 1.0V, 1.2V, 3.3V) generated from a 5V or 12V rail. The AP63301WU-7's 0.8V reference and 3 A capability easily power a 1.2V/2 A core or 3.3V/3 A I/O rail. Peak current-mode control with internal compensation delivers fast load-step behavior when the SoC wakes from sleep.
Recomendado
Automotive Accessory Power (Non-Safety)
12V automotive rails see 6V cranking dips up to 18V load-dump transients. The AP63301WU-7's 32V absolute-maximum VIN tolerates load-dump, while its 3.8V minimum starts cleanly during cranking. The TSOT-23-6 footprint is well-suited to infotainment, ambient lighting, and accessory USB hubs. For safety-critical powertrain or ADAS rails, an AEC-Q100-qualified part is recommended instead.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para AP63301WU-7 — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | AP63300WU-7 | AP63205WU-7 |
|---|---|---|---|
| Package | TSOT-23-6 | TSOT-23-6 - same | TSOT-23-6 - same |
| Brand | Diodes Incorporated | Diodes Incorporated | Diodes Incorporated |
| Input Voltage Range | 3.8 V to 32 V | 3.8 V to 32 V | 3.8 V to 18 V |
| Continuous Output Current | 3 A | 3 A | 2 A |
| AEC-Q100 Automotive Grade | No | No | No |
Diferenciadores clave
- EMI-optimized gate driver without FSS (frente a AP63300WU-7)
- 3 A output current in TSOT-23-6 (frente a AP63205WU-7)
- Wide 32V VIN for industrial and telecom (frente a Generic 18V buck in TSOT-23-6)
Notas de diseño
Place the input ceramic capacitor (≥ 10 µF X7R) directly between VIN (pin 4) and GND (pin 2) using the shortest possible trace. Place the bootstrap capacitor (100 nF) between BST (pin 5) and SW (pin 3) using a short, wide trace. The feedback divider (R1 from VOUT to FB, R2 from FB to GND) must connect to a Kelvin point after the output capacitor to prevent load-regulation errors. The exposed pad (EP) under the TSOT-23-6 must be soldered to a continuous ground copper pour to achieve rated thermal performance.
Estimated: at VIN = 24 V, VOUT = 5 V, and IOUT = 3 A, power dissipation P = (VIN - VOUT) × IOUT × (1/η - 1) ≈ 1.0 W assuming 92% efficiency. With θJA ≈ 60 °C/W on a 4-layer 1 oz JEDEC PCB, the junction rises ~60 °C above ambient; at 25 °C ambient the junction reaches ~85 °C, well within the 125 °C limit. For continuous VIN ≥ 28 V at 3 A, increase copper area or reduce VIN-VOUT differential.
Do not leave the BST pin floating - the converter will not start. Do not load the SW node with anything other than the inductor. Do not program VOUT above approximately VIN - 1.5 V or the high-side MOSFET will not turn on long enough to regulate. When using EN, ensure the source can drive above the 1.18 V rising threshold; tying EN directly to VIN is allowed because EN is a high-voltage tolerant pin. Avoid placing the feedback trace near the SW trace to prevent noise injection into the FB node.
Información de cumplimiento
RoHS and REACH compliant per Diodes Incorporated product page. Not AEC-Q100 qualified - choose an AEC-Q100 part for automotive safety applications. Halogen-free per JEDEC JS709.
