BD3180FV-E2 - High-Side Current Sense Amp | ROHM
N.º de pieza: BD3180FV-E2 ✓ ActivoBD3180FV-E2 Descripción general
A current sense amplifier is a specialized analog amplifier that measures the voltage across a low-value shunt resistor and converts that differential signal into a proportional output voltage. In the measurement chain, the shunt resistor -> current sense amplifier -> analog-to-digital converter -> host processor, the amplifier must reject supply noise, offset error, and common-mode voltage without saturating.
The BD3180FV-E2 provides one measurement channel in a compact 8-SSOP package. Its single-channel arrangement suits power-management controllers, motor-control systems, battery-management equipment, and compact industrial modules where board area is restricted. The manufacturer's BD3180FV documentation identifies the device as a super high accuracy current detection amplifier.
The 8-SSOP package allows the amplifier to be mounted alongside a shunt resistor and analog-to-digital converter on a densely populated printed circuit board. Because the output of a current sense amplifier reflects both the measured current and the amplifier's gain, calibration and shunt selection must be coordinated. Keep shunt connections short and route the differential sense traces as a compact, matched pair to limit pickup from switching nodes.
Typical uses include DC motor current regulation in consumer appliances, current feedback in LED lighting systems, load monitoring in industrial control boards, and protection functions in power-conversion equipment. The amplifier is particularly relevant where the monitored rail sits at a voltage well above ground and a conventional low-voltage amplifier would lack sufficient common-mode headroom.
For the best measurement result, select the shunt resistance and amplifier gain together so that the maximum expected current produces an output within the input range of the downstream converter. Place input and reference components close to their associated pins, verify the complete sense path against the manufacturer's application guidance, and confirm the maximum common-mode voltage against the specific operating rail.
This page organizes the BD3180FV-E2 package information, technical attributes, application guidance, and sourcing questions into a single engineering reference. It also identifies which parameters require confirmation from the manufacturer datasheet before a production design is released.
Alternativas directas para BD3180FV-E2 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
No hay alternativas directas disponibles para este producto.
Solicitar alternativasBD3180FV-E2 Valores máximos y características eléctricas
| Product Type | High-side current sense amplifier |
| Manufacturer Description | Super high accuracy current detection amplifier |
| Number of Circuits | 1 circuit |
| Channel Count | 1 channel |
| Encapsulado | 8-SSOP |
| Tipo de montaje | Surface mount |
Guía de configuración de pines de BD3180FV-E2 8-ssop
Configuración de pines para BD3180FV-E2 (encapsulado 8-ssop). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para BD3180FV-E2.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
BD3180FV-E2 es adecuado para 6 aplicacións: DC Motor Current Feedback, Power Supply Load Monitoring, LED Lighting Driver Regulation, Battery Charge Current Monitoring, Industrial Control Module Protection, Consumer Appliance Load Sensing.
DC Motor Current Feedback
BD3180FV-E2 fits motor drives that require an analog indication of supply current for torque control, stall detection, or current limiting. Its high-side input common-mode characteristic allows the shunt to sit in the positive motor rail instead of near ground. Place the amplifier near the shunt, route the sense pair away from motor-switching edges, and select the shunt and gain so peak current keeps the amplifier output within the controller input range.
Recomendado
Power Supply Load Monitoring
The single measurement channel in BD3180FV-E2 is suitable for monitoring load current in a compact AC-DC or DC-DC power module. High-side sensing keeps the shunt installation simple and avoids grounding the monitored rail through a low-side shunt path. Confirm that the monitored rail stays inside the amplifier's common-mode limits, then feed the output into an analog-to-digital converter for telemetry, overload reporting, or adaptive power management.
Recomendado
LED Lighting Driver Regulation
BD3180FV-E2 can provide the current feedback signal required by a constant-current LED driver that regulates power from a high-side source. Placing a shunt in the LED supply path and amplifying its differential voltage creates a measurement proportional to LED current, allowing the controller to compensate for forward-voltage variation. Keep the sense traces compact, verify the amplifier's common-mode range against the LED rail, and account for shunt power at the maximum LED current.
Recomendado
Battery Charge Current Monitoring
BD3180FV-E2 is applicable to battery-management circuitry that measures charge or discharge current in a high-side conductor. The 8-SSOP package supports compact control boards, while the dedicated current sense amplifier simplifies implementation compared with a discrete differential amplifier network. The shunt value must be chosen for the lowest current that must be resolved, and the gain, offset, and analog-to-digital converter resolution must be evaluated as a combined measurement chain.
Recomendado
Industrial Control Module Protection
BD3180FV-E2 supports fast protection functions in compact industrial controllers where a motor, actuator, or solenoid load must be limited to a safe current. The amplifier output can feed a comparator and logic stage for an overcurrent event, while an ADC path can preserve the measurement for diagnostics. Set the threshold with margin for component tolerances, confirm the amplifier's response time, and keep the high-current switching paths away from the shunt connections.
Recomendado
Consumer Appliance Load Sensing
BD3180FV-E2 can support load detection, heater regulation, and energy-related feedback in compact consumer appliances. The single-channel 8-SSOP device occupies little board area and measures a high-side rail without requiring the controlled load to share a low-side sensing return with the controller. Select the shunt for both power handling and measurement resolution, and verify the thermal performance of the complete sense path rather than only the amplifier package.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para BD3180FV-E2 — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto |
|---|---|
| Brand | ROHM Semiconductor |
| Package | 8-SSOP |
| Product Type | High-side current sense amplifier |
| Number of Circuits | 1 circuit |
| Mounting Type | Surface mount |
Diferenciadores clave
- Dedicated high-side current measurement in a compact package (frente a Discrete shunt-amplifier implementation)
- Common-mode range suited to elevated sensing rails (frente a Basic ground-referenced signal amplifier)
- Accuracy-oriented current detection architecture (frente a Simple transistor current switch)
Notas de diseño
Place the shunt resistor and BD3180FV-E2 close to each other, and route the two sense connections as a short differential pair. The input traces should not run parallel to motor phases, switching-node copper, or high-current return paths because capacitive and inductive coupling can appear as current-measurement error. If the shunt is remote from the amplifier, add the trace and connector resistance to the gain and offset calculation.
Check the maximum monitored-rail voltage against the amplifier's input common-mode range before committing the schematic. A high-side sense amplifier can still saturate if the conductor voltage exceeds that rating even when its supply pin is correct. Also verify that the shunt's power rating, the amplifier's supply voltage, and the output swing remain adequate at maximum load and minimum load conditions.
Treat the shunt as a precision resistive element rather than a general-purpose power resistor. Select a low temperature-coefficient part with adequate pulse tolerance and thermal margin, and avoid excessive temperature rise because resistance drift directly changes the current calculation. Pair gain-setting resistors with suitable tolerances and temperature coefficients, and treat amplifier offset as part of the minimum resolvable current.
Calculate shunt dissipation as I-squared-R before finalizing the current range, then confirm the amplifier's operating and quiescent current against the power-supply budget. At the maximum continuous load, the sense resistor may become the hottest component in the measurement path. Maintain copper area and thermal vias around both the shunt and the 8-SSOP package so current accuracy does not change as the assembly warms.
Información de cumplimiento
The BD3180FV documentation does not establish the RoHS, REACH, halogen-free, or conflict-minerals status for this ordering code. Confirm environmental and material compliance with the manufacturer before release.