CD40103BD - 8-Bit Synchronous Down Counter | Harris
N.º de pieza: CD40103BD ✓ ActivoCD40103BD Descripción general
A synchronous binary counter is a digital logic device that advances through a fixed binary sequence in response to clock transitions. Unlike an asynchronous ripple counter, the CD40103BD changes its outputs at the same clock transition, reducing accumulated propagation delay across the eight output stages. Presettable counters add a parallel-load function so the internal count can be set to a chosen value before counting resumes. This device therefore belongs to the CMOS 4000-series counter family and the broader category of counters, dividers, and logic ICs.
Principal features include 8-bit counting capacity, binary count direction, one counter element, positive-edge triggering, synchronous operation, and a preset capability. The counter operates from a dual power supply, making its clock, preset, and count-data interface electrically compatible with other CD4000-series CMOS devices. Because the counter is synchronous, it is better suited to accurate frequency division and multi-digit count sequencing than a ripple counter with cumulative stage delay.
Typical uses include programmable frequency dividers, digital timing chains, industrial sequence controllers, event counters, timing-reference circuits, and test equipment. In each case, the eight count outputs can represent the current binary count, divide an input clock by a selected power of two, or provide parallel count data for downstream decoding. The synchronous count transition also helps maintain predictable timing relationships between adjacent counter outputs.
In a new PCB design, follow the manufacturer pin-description table when connecting the clock, count-data, preset, carry, and reset inputs. Allow adequate signal-transition time for the CMOS inputs, and use pull-down or pull-up resistors where an unused control input requires a defined bias. Treat the 16-lead ceramic DIP as a through-hole package with no exposed thermal pad. Before substituting a different manufacturer or temperature grade, verify the counter direction, clock-edge convention, preset polarity, reset behavior, supply voltage, and absolute maximum ratings in the relevant datasheet.
This page consolidates the available manufacturer and distributor information for CD40103BD, compares pin-compatible counter options, and summarizes the design checks needed for reliable integration into legacy CMOS and industrial counter systems.
Alternativas directas para CD40103BD — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con CD40103BD (mismo factor de forma y huella) — difiere en Preset Capability.
CD40103BE
✅ Sustitución directaConsulte el precio
Ver hoja de datos →CD40103BM
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
CD40103BF3A
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
CD40103BC
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
CD40103BP
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
CD40103BD Valores máximos y características eléctricas
| Product Type | 8-Bit Presettable Synchronous Binary Down Counter |
| Manufacturer | Harris Corporation |
| Logic Family | CMOS 4000 Series |
| Counter Element Count | 1 element |
| Counting Capacity | 8 bits |
| Count Direction | Down |
| Count Sequence | Binary |
| Clock Edge | Positive edge |
| Counter Type | Synchronous |
| Preset Capability | Yes, presettable |
| Package Type | 16-CDIP ceramic dual-in-line package |
| Terminal Count | 16 terminals |
| Tipo de montaje | Through-hole |
| Package Shape | Rectangular |
| Temperature Grade | Military |
Guía de configuración de pines de CD40103BD rectangular
Configuración de pines para CD40103BD (encapsulado rectangular). Este CI digital incluye GPIO, interfaces de comunicación (UART, SPI, I2C) y pines de alimentación. Consulte la hoja de datos del fabricante para conocer las funciones alternativas de los pines y las opciones de configuración. Esencial para el diseño de sistemas embebidos y el diseño de PCB.
No hay datos detallados de patillaje disponibles para CD40103BD.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
CD40103BD es adecuado para 6 aplicacións: Programmable Frequency Divider, Industrial Event and Cycle Counter, Digital Timing and Sequence Control, Frequency Division for Clock Conditioning, Legacy Instrumentation and Test Equipment, Multistage Counter and Divider Chain.
Programmable Frequency Divider
The CD40103BD fits a programmable frequency-divider stage because its 8-bit synchronous binary down counter can divide an input clock by a selected power of two or a preset-derived interval. Preset the counter with the intended terminal value, apply the clock to the positive-edge clock input, and decode the count outputs for the required divide ratio. Because the counting transitions are synchronous, decoded outputs are more closely aligned than those from a ripple counter. Confirm the maximum clock rate at the chosen supply voltage and temperature before sizing the clock driver.
Industrial Event and Cycle Counter
Use the CD40103BD to count machine cycles, product events, or elapsed timing intervals in industrial control equipment. Its 8-bit count range provides 256 states, and the parallel preset capability allows each counting interval to start from a defined value. The positive-edge trigger helps align counting with an external sensor-conditioned clock, while the binary outputs can feed a display driver or comparison logic. For noisy factory environments, protect sensor signals with appropriate filtering and keep the counter supply referenced to the same system ground.
Digital Timing and Sequence Control
The CD40103BD suits cascaded timing and sequencing circuits where a repeatable binary count drives state transitions. Load a preset value, use the carry output to trigger the next stage, and cascade multiple counters for longer timing intervals. Synchronous count transitions provide predictable relationships between the eight outputs, and the 16-lead ceramic DIP supports through-hole construction on legacy or industrial control boards. Confirm preset and reset polarity in the pin table so the counter starts in the intended state after power restoration.
Frequency Division for Clock Conditioning
When an existing clock must be reduced to a lower control rate, the CD40103BD provides an 8-bit binary down-counting stage with selectable presets. Preset the counter so its terminal condition occurs at the required division interval, then use one count output as the conditioned clock. Synchronous operation reduces accumulated skew across the count stages, which is valuable when the divided signal feeds another synchronous control block. Evaluate the setup and clock-transition requirements of the counter at the actual supply voltage.
Legacy Instrumentation and Test Equipment
The CD40103BD is a practical fit for repair and modernization of legacy CMOS test and measurement equipment that requires an 8-bit synchronous binary down counter. The military-grade 16-CDIP construction and through-hole format suit older instrument boards and connectorized assemblies. Its eight parallel count outputs can drive calibration logic, range indicators, or timing markers. Confirm pinout, supply rails, and input levels before installation, since vintage equipment may use nonstandard interface conventions.
Multistage Counter and Divider Chain
Cascade multiple CD40103BD devices to create wider counting ranges or a multi-decade divider. Each 8-bit stage can present a hexadecimal count, and carry or terminal-count signaling can enable the next device for higher-order counting. Using synchronous counter stages keeps state transitions coordinated compared with independent ripple chains. Check the carry timing, clock loading, and inter-stage logic levels against the manufacturer timing diagrams before cascading devices at high input frequencies.
Datos de referencia de ingeniería para CD40103BD — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | CD40103BE | CD40103BM | CD40103BF3A | CD40103BC | CD40103BP |
|---|---|---|---|---|---|---|
| Package | 16-CDIP ceramic DIP | 16-lead plastic DIP | 16-lead DIP | 16-lead ceramic DIP | 16-lead DIP | 16-lead plastic DIP |
| Brand | Harris Corporation | Texas Instruments | Texas Instruments | Texas Instruments | Fairchild | RCA |
| Counter Type | Binary down counter | Binary down counter | Binary down counter | Binary down counter | Binary down counter | Binary down counter |
| Count Capacity | 8 bits | 8 bits | 8 bits | 8 bits | 8 bits | 8 bits |
| Counting Mode | Synchronous | Synchronous | Synchronous | Synchronous | Synchronous | Synchronous |
| Clock Edge | Positive edge | Positive edge | Positive edge | Positive edge | Positive edge | Positive edge |
| Preset Function | Yes | Yes | Yes | Yes | Yes | Yes |
| Logic Technology | CMOS | CMOS | CMOS | CMOS | CMOS | CMOS |
Diferenciadores clave
- Preserves the military-grade 16-CDIP construction (frente a CD40103BE)
- Maintains the same CD40103B counter architecture (frente a CD40103BF3A)
- Uses synchronous counting rather than ripple-derived transitions (frente a CD40103BC)
Notas de diseño
Do not assume that every CD40103 ordering code is an unrestricted substitute. The D suffix identifies the Harris 16-CDIP military-grade part, while E, M, F3A, C, and P denote different package, material, or temperature combinations. Before replacement, verify pin functions, preset polarity, reset behavior, supply limits, and temperature requirements in the manufacturer datasheet for the exact ordering code.
Keep clock, preset, and count-data traces short and route them away from noisy switching nodes. The CD40103BD changes its count outputs on a positive edge, so clock bounce or ringing can cause an unintended count transition. Use a clean gate or Schmitt-trigger stage when the clock originates in a mechanical switch, relay contact, or long cable, and provide a defined logic level to every unused CMOS input.
The CD40103BD uses a 16-lead through-hole ceramic DIP package. Match the row spacing and drill pattern of the original 16-CDIP footprint, maintain adequate clearance between adjacent row holes, and consider a socket when field replacement or upgrade is expected. Ceramic DIP packages are more susceptible to mechanical stress during soldering and insertion, so support the package and avoid forceful lead alignment against a socketed board.
Información de cumplimiento
The CD40103BD is identified as a military-grade Harris Corporation 16-CDIP logic counter. No current RoHS, REACH, lead-free, halogen-free, or conflict-minerals statements were found for this ordering code, so these fields remain unknown.