CY7C68000-56LFXCT - USB 2.0 Transceiver | Infineon
N.º de pieza: CY7C68000-56LFXCT ✓ ActivoCY7C68000-56LFXCT Descripción general
A USB transceiver is the physical-layer interface between a USB controller and its external data bus. It belongs to the broader USB interface IC category, combining transmitter and receiver functions into one device while leaving protocol handling, enumeration, and data transfer to a controller or programmable logic. The integrated 1/1 transceiver architecture reduces external USB PHY component count in USB-to-parallel systems.
The key operating options are full-speed USB 2.0 operation, selectable 16-bit/30 MHz or 8-bit/60 MHz parallel operation, and a compact 56-QFN package measuring 8 x 8 mm. These features allow the device to interface with parallel processors, FPGAs, and USB controllers while supporting two different bus-width and clocking arrangements.
The serial/deserializer architecture converts between differential USB signaling and the device's parallel data interface. For a 16-bit configuration, data is transferred across 16 parallel bits at 30 MHz; for an 8-bit configuration, eight parallel bits are transferred at 60 MHz. The effective parallel word-transfer rate remains aligned with the full-speed USB signaling requirement.
Typical uses include USB-to-parallel bridges, embedded USB test equipment, data-acquisition controllers, FPGA-based USB endpoints, and legacy systems that need a dedicated full-speed USB physical-layer device. In each case, the controller must implement the applicable USB protocol, while the CY7C68000-56LFXCT handles the physical serial and parallel interface conversion.
PCB design should preserve high-speed USB signal integrity by following the manufacturer's pin, layout, and decoupling guidance. Keep differential USB routing short and symmetrical, provide a continuous ground reference, place bypass capacitors near the appropriate supply pins, and avoid routing through split plane boundaries. The exposed-pad connection and package thermal requirements should follow the manufacturer land-pattern guidance.
This product page combines interface and package facts with application guidance, practical layout considerations, and same-family replacement options. It is intended to help engineers determine whether the 16-/8-bit UTMI configuration and 56-QFN footprint match the target USB system before releasing a design or replacement order.
Alternativas directas para CY7C68000-56LFXCT — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con CY7C68000-56LFXCT (mismo factor de forma y huella) — difiere en USB Specification, Architecture, Maximum USB Data Rate, Package Dimensions, Package Type.
CY7C68000A-56LFXCT
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
CY7C68000A-56LFXC
✅ Sustitución directaConsulte el precio
Ver hoja de datos →CY7C68001-56LTXC
✅ Sustitución directaConsulte el precio
Ver hoja de datos →CY7C68001-56LFXCT
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
CY7C68000-56LFXCT Especificaciones
| Device Type | 1/1 USB 2.0 transceiver |
| USB Specification | USB 2.0 full-speed |
| Parallel Interface Width | 16 bits or 8 bits |
| 16-Bit Interface Clock | 30 MHz |
| 8-Bit Interface Clock | 60 MHz |
| Transceiver Configuration | 1 transmit and 1 receive path |
| Architecture | Serial/deserializer to parallel interface |
| Package Type | 56-QFN |
| Package Dimensions | 8 x 8 mm |
| Tipo de montaje | Surface mount |
| Maximum USB Data Rate | 12 Mbit/s |
Guía de configuración de pines de CY7C68000-56LFXCT 8 x 8 mm
Configuración de pines para CY7C68000-56LFXCT (encapsulado 8 x 8 mm). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para CY7C68000-56LFXCT.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
CY7C68000-56LFXCT es adecuado para 6 aplicacións: FPGA-Based USB Controller Interface, USB-to-Parallel Data Bridge, Embedded USB Test and Measurement, Data-Acquisition Controller, Industrial USB-to-Device Interface, Legacy USB-to-Processor Adapter.
FPGA-Based USB Controller Interface
The CY7C68000-56LFXCT is suitable for an FPGA-based USB controller because it provides a full-speed USB 2.0 physical layer alongside a selectable parallel interface. A 16-bit connection operating at 30 MHz can support wider datapath transfers, while an eight-bit connection at 60 MHz offers an alternative timing arrangement. The FPGA handles enumeration, descriptors, endpoints, and protocol behavior, while the transceiver handles serial signaling and parallel conversion. Designers should preserve the package's USB trace geometry, provide an uninterrupted ground plane, and validate the exposed-pad layout against the manufacturer drawing before fabrication.
Recomendado
USB-to-Parallel Data Bridge
The CY7C68000-56LFXCT can form the physical layer of a USB-to-parallel bridge by accepting full-speed USB 2.0 traffic and presenting it to a parallel controller interface. Its two documented bus arrangements let the designer select 16 bits at 30 MHz for a wider datapath or eight bits at 60 MHz for a more compact interface. The bridge logic must still implement USB enumeration and protocol translation. Because the device performs high-speed edge signaling internally, differential pair routing should be short, length-matched, and referenced to a continuous ground plane.
Recomendado
Embedded USB Test and Measurement
The CY7C68000-56LFXCT can support embedded test and measurement equipment that exchanges full-speed USB 2.0 data with a programmable acquisition or control subsystem. The 16-bit/30 MHz option can reduce the number of parallel transfer cycles for buffered data, while the eight-bit/60 MHz option can simplify interface width. Instrument firmware must implement the required command and measurement protocols independently of the transceiver. Board implementation should account for analog input isolation, grounding, and USB connector placement so test-domain noise does not degrade signal acquisition.
Recomendado
Data-Acquisition Controller
The CY7C68000-56LFXCT is appropriate for a data-acquisition controller that needs a dedicated full-speed USB 2.0 physical interface to a processor or FPGA. Its selectable parallel modes allow the digital engine to use either a 16-bit datapath at 30 MHz or an eight-bit datapath at 60 MHz according to throughput and routing requirements. The controller remains responsible for buffering, timing, and data integrity. Keep the USB differential pair away from sensitive analog inputs and use the manufacturer's recommended supply bypassing and exposed-pad construction.
Recomendado
Industrial USB-to-Device Interface
The CY7C68000-56LFXCT can be used in an industrial device interface that exchanges full-speed USB 2.0 data with local control logic. Its compact 56-QFN package measures 8 x 8 mm and supports both a 16-bit/30 MHz and an eight-bit/60 MHz parallel configuration, allowing board partitioning to follow the controller architecture. The external controller must provide compatible clocking and handle protocol behavior. Industrial enclosure grounding, cable shielding, and ESD strategy should be designed at the connector because the transceiver package alone does not replace system-level protection.
Recomendado
Legacy USB-to-Processor Adapter
The CY7C68000-56LFXCT can bridge a legacy parallel processor architecture to a full-speed USB 2.0 host. Its serial/deserializer function handles the transition between differential USB signaling and an eight-bit or 16-bit parallel bus, reducing the need for a discrete USB PHY. The processor or FPGA must implement the required USB state machine and endpoint behavior. Timing closure becomes more important in eight-bit/60 MHz operation, so confirm clock and data-skew budgets against the manufacturer interface timing specifications.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para CY7C68000-56LFXCT — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | CY7C68000A-56LFXCT | CY7C68000A-56LFXC | CY7C68001-56LTXC | CY7C68001-56LFXCT |
|---|---|---|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| Package | 56-QFN (8x8) | 56-QFN (8x8) | 56-QFN (8x8) | 56-QFN (8x8) | 56-QFN (8x8) |
Diferenciadores clave
- Selectable parallel width and clock combination (frente a CY7C68000A-56LFXCT)
- Established base revision for continuity (frente a CY7C68001-56LFXCT)
- Single-package transceiver integration (frente a CY7C68000A-56LFXC)
Notas de diseño
Route the USB differential pair as a controlled-impedance, tightly coupled pair with symmetric geometry and no intervening layer changes. Keep the pair short and provide a continuous ground reference beneath it. Place the transceiver close to the USB connector or board entry point so common-mode noise and ESD transients are not distributed through sensitive functional areas.
Place input, output, and bypass capacitors close to their associated package pins using the shortest practical traces. Follow the manufacturer land pattern for the 56-QFN exposed pad and connect the thermal pad to the required ground and copper area. Verify paste, solder mask, and assembly clearance because the library does not contain a dedicated 56-QFN footprint.
Design the parallel side around the selected operating mode: 16 bits at 30 MHz or eight bits at 60 MHz. In the eight-bit configuration, data and clock skew become more significant even though the package is unchanged. Maintain matched output timing at the controller or FPGA, avoid stubs, and review the manufacturer interface timing limits before selecting component tolerances or board-routing assumptions.
Do not treat a matching 56-QFN package as proof of interchangeability. Before substituting an A-revision or CY7C68001-family device, compare every pin name, supply requirement, clock input, timing parameter, USB electrical characteristic, and exposed-pad connection. Preserve the exact revision in new production designs unless the manufacturer explicitly approves the change.
Información de cumplimiento
The available product information does not state the requested environmental or automotive compliance declarations. Request current compliance documentation through the Request a Quote form.