Infineon

CY7C68000-56LFXCT - USB 2.0 Transceiver | Infineon

MPN: CY7C68000-56LFXCT ✓ פעיל
56-QFN Package 30 MHz Speed
כמות הזמנה מינימלית: 1 |

CY7C68000-56LFXCT סקירה

The Infineon CY7C68000-56LFXCT is a 1/1 full-speed USB 2.0 transceiver with a serial/deserializer and parallel UTMI-compatible interface, housed in a 56-QFN (8 x 8 mm) package. It supports a 16-bit parallel interface operating at 30 MHz or an 8-bit parallel interface operating at 60 MHz.

A USB transceiver is the physical-layer interface between a USB controller and its external data bus. It belongs to the broader USB interface IC category, combining transmitter and receiver functions into one device while leaving protocol handling, enumeration, and data transfer to a controller or programmable logic. The integrated 1/1 transceiver architecture reduces external USB PHY component count in USB-to-parallel systems.

The key operating options are full-speed USB 2.0 operation, selectable 16-bit/30 MHz or 8-bit/60 MHz parallel operation, and a compact 56-QFN package measuring 8 x 8 mm. These features allow the device to interface with parallel processors, FPGAs, and USB controllers while supporting two different bus-width and clocking arrangements.

The serial/deserializer architecture converts between differential USB signaling and the device's parallel data interface. For a 16-bit configuration, data is transferred across 16 parallel bits at 30 MHz; for an 8-bit configuration, eight parallel bits are transferred at 60 MHz. The effective parallel word-transfer rate remains aligned with the full-speed USB signaling requirement.

Typical uses include USB-to-parallel bridges, embedded USB test equipment, data-acquisition controllers, FPGA-based USB endpoints, and legacy systems that need a dedicated full-speed USB physical-layer device. In each case, the controller must implement the applicable USB protocol, while the CY7C68000-56LFXCT handles the physical serial and parallel interface conversion.

PCB design should preserve high-speed USB signal integrity by following the manufacturer's pin, layout, and decoupling guidance. Keep differential USB routing short and symmetrical, provide a continuous ground reference, place bypass capacitors near the appropriate supply pins, and avoid routing through split plane boundaries. The exposed-pad connection and package thermal requirements should follow the manufacturer land-pattern guidance.

This product page combines interface and package facts with application guidance, practical layout considerations, and same-family replacement options. It is intended to help engineers determine whether the 16-/8-bit UTMI configuration and 56-QFN footprint match the target USB system before releasing a design or replacement order.

חלופות תחליף ישיר עבור CY7C68000-56LFXCT — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

וריאנטים בסדרה זו

דגמים מאותה סדרה התואמים Drop-in עם CY7C68000-56LFXCT (אותו גורם צורה וטביעת רגל) — שונים ב USB Specification, Architecture, Maximum USB Data Rate, Package Dimensions, Package Type.

Infineon
USB Specification: USB 2.0
Architecture: MoBL-USB TX2 USB 2.0 UTMI transceiver
Maximum USB Data Rate: 480 Mbps
השווה עם CY7C68000-56LFXCT →
Infineon
USB Specification: USB 2.0
Package Dimensions: 8 mm x 8 mm
Package Type: 56-pin QFN with exposed pad
השווה עם CY7C68000-56LFXCT →

CY7C68000A-56LFXCT

✅ Drop-In
📦 56-QFN (8x8)
A-revision device with the same 1/1 full-speed USB 2.0 interface and 56-QFN 8x8 package; revision-specific electrical and timing changes require verification

📋 חלופה להתייחסות (לא בקטלוג)

CY7C68000A-56LFXC

✅ Drop-In
Infineon
📦 56-QFN (8x8)
1/1 USB 2.0 transceiver · USB 2.0 · 480 Mbps · 16 bits at 30 MHz · 8 bits at 60 MHz · 60 Mbit/s · USB 2.0 test modes · 56-pin QFN, 8 mm x 8 mm

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

CY7C68001-56LTXC

✅ Drop-In
Infineon
📦 56-QFN (8x8)
USB 2.0 full-speed and high-speed USB interface device · USB 2.0 · Full Speed and High Speed · Parallel interface · 3.3 V · 56-pin QFN with exposed pad · 8 mm x 8 mm · 56 pins

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

CY7C68001-56LFXCT

✅ Drop-In ⚠️ מפרטים לא מאומתים
📦 56-QFN (8x8)
Same-family 56-QFN variant intended for the same full-speed USB transceiver function; pin, clock, and device-specific differences require verification

📋 חלופה להתייחסות (לא בקטלוג)

CY7C68000-56LFXCT מפרטים

Device Type 1/1 USB 2.0 transceiver
USB Specification USB 2.0 full-speed
Parallel Interface Width 16 bits or 8 bits
16-Bit Interface Clock 30 MHz
8-Bit Interface Clock 60 MHz
Transceiver Configuration 1 transmit and 1 receive path
Architecture Serial/deserializer to parallel interface
Package Type 56-QFN
Package Dimensions 8 x 8 mm
סוג הרכבה Surface mount
Maximum USB Data Rate 12 Mbit/s

מדריך תצורת פינים של CY7C68000-56LFXCT 8 x 8 mm

תצורת פינים עבור CY7C68000-56LFXCT (מארזת 8 x 8 mm). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.

תרשים פינים של מארזת 8 x 8 mm עבור CY7C68000-56LFXCT

אין נתוני פריסת פינים מפורטים עבור CY7C68000-56LFXCT.

עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.

יישומים טיפוסיים

CY7C68000-56LFXCT מתאים עבור 6 יישוםs: FPGA-Based USB Controller Interface, USB-to-Parallel Data Bridge, Embedded USB Test and Measurement, Data-Acquisition Controller, Industrial USB-to-Device Interface, Legacy USB-to-Processor Adapter.

🖥️

FPGA-Based USB Controller Interface

The CY7C68000-56LFXCT is suitable for an FPGA-based USB controller because it provides a full-speed USB 2.0 physical layer alongside a selectable parallel interface. A 16-bit connection operating at 30 MHz can support wider datapath transfers, while an eight-bit connection at 60 MHz offers an alternative timing arrangement. The FPGA handles enumeration, descriptors, endpoints, and protocol behavior, while the transceiver handles serial signaling and parallel conversion. Designers should preserve the package's USB trace geometry, provide an uninterrupted ground plane, and validate the exposed-pad layout against the manufacturer drawing before fabrication.

🌐

USB-to-Parallel Data Bridge

The CY7C68000-56LFXCT can form the physical layer of a USB-to-parallel bridge by accepting full-speed USB 2.0 traffic and presenting it to a parallel controller interface. Its two documented bus arrangements let the designer select 16 bits at 30 MHz for a wider datapath or eight bits at 60 MHz for a more compact interface. The bridge logic must still implement USB enumeration and protocol translation. Because the device performs high-speed edge signaling internally, differential pair routing should be short, length-matched, and referenced to a continuous ground plane.

🔧

Embedded USB Test and Measurement

The CY7C68000-56LFXCT can support embedded test and measurement equipment that exchanges full-speed USB 2.0 data with a programmable acquisition or control subsystem. The 16-bit/30 MHz option can reduce the number of parallel transfer cycles for buffered data, while the eight-bit/60 MHz option can simplify interface width. Instrument firmware must implement the required command and measurement protocols independently of the transceiver. Board implementation should account for analog input isolation, grounding, and USB connector placement so test-domain noise does not degrade signal acquisition.

📡

Data-Acquisition Controller

The CY7C68000-56LFXCT is appropriate for a data-acquisition controller that needs a dedicated full-speed USB 2.0 physical interface to a processor or FPGA. Its selectable parallel modes allow the digital engine to use either a 16-bit datapath at 30 MHz or an eight-bit datapath at 60 MHz according to throughput and routing requirements. The controller remains responsible for buffering, timing, and data integrity. Keep the USB differential pair away from sensitive analog inputs and use the manufacturer's recommended supply bypassing and exposed-pad construction.

🏭

Industrial USB-to-Device Interface

The CY7C68000-56LFXCT can be used in an industrial device interface that exchanges full-speed USB 2.0 data with local control logic. Its compact 56-QFN package measures 8 x 8 mm and supports both a 16-bit/30 MHz and an eight-bit/60 MHz parallel configuration, allowing board partitioning to follow the controller architecture. The external controller must provide compatible clocking and handle protocol behavior. Industrial enclosure grounding, cable shielding, and ESD strategy should be designed at the connector because the transceiver package alone does not replace system-level protection.

💻

Legacy USB-to-Processor Adapter

The CY7C68000-56LFXCT can bridge a legacy parallel processor architecture to a full-speed USB 2.0 host. Its serial/deserializer function handles the transition between differential USB signaling and an eight-bit or 16-bit parallel bus, reducing the need for a discrete USB PHY. The processor or FPGA must implement the required USB state machine and endpoint behavior. Timing closure becomes more important in eight-bit/60 MHz operation, so confirm clock and data-skew budgets against the manufacturer interface timing specifications.

סיכום מוצרים מומלצים

CY7C68000A-56LFXCT Same-family full-speed USB transceiver candidate בשימוש ב-: FPGA-Based USB Controller Interface, Embedded USB Test and Measurement, Industrial USB-to-Device Interface CY7C68001-56LFXCT Same-family 56-QFN transceiver candidate בשימוש ב-: FPGA-Based USB Controller Interface, Data-Acquisition Controller CY7C68000A-56LFXC Infineon בשימוש ב-: USB-to-Parallel Data Bridge, Industrial USB-to-Device Interface CY7C68001-56LTXC Infineon בשימוש ב-: USB-to-Parallel Data Bridge, Data-Acquisition Controller, Legacy USB-to-Processor Adapter CY7C68000-56LFXCT Infineon בשימוש ב-: Embedded USB Test and Measurement, Legacy USB-to-Processor Adapter
What is the CY7C68000-56LFXCT?
The CY7C68000-56LFXCT is a 1/1 full-speed USB 2.0 transceiver that converts between differential USB signaling and a parallel interface. According to the manufacturer datasheet, it supports 16 parallel bits at 30 MHz or eight parallel bits at 60 MHz and is packaged in a 56-QFN measuring 8 x 8 mm.
What are the key specifications of CY7C68000-56LFXCT that engineers should know?
The CY7C68000-56LFXCT combines a full-speed USB 2.0 1/1 transceiver with selectable 16-bit/30 MHz and 8-bit/60 MHz parallel operation. According to the manufacturer datasheet, its serial/deserializer provides the physical interface, while the 56-QFN package measures 8 x 8 mm. These are the central functional, clocking, and packaging considerations when selecting it.
What parallel interface modes does CY7C68000-56LFXCT support?
The CY7C68000-56LFXCT supports two parallel-interface configurations. According to the manufacturer datasheet, the first mode transfers 16 bits at 30 MHz, while the second transfers eight bits at 60 MHz. The chosen mode must be supported by the connected USB controller, FPGA, or programmable logic interface.
Where can I download the CY7C68000-56LFXCT datasheet PDF?
The CY7C68000-56LFXCT datasheet PDF is available from the official-device document hosted in the product's technical document set. It describes the USB 2.0 serial/deserializer architecture, 16-bit and 8-bit parallel modes, 30 MHz and 60 MHz clocks, and the 56-QFN footprint. Use the pin-description and layout sections for board implementation.
Where can I find the CY7C68000-56LFXCT pinout?
The CY7C68000-56LFXCT pinout is shown in the pin-description table and package drawing of the manufacturer datasheet. Use that table to assign the USB, parallel-interface, power, ground, and exposed-pad connections for all 56 package positions. The complete pin list is not reproduced here because the available document excerpt does not show every terminal name.
Is CY7C68000-56LFXCT suitable for an FPGA-based USB interface?
Yes, the CY7C68000-56LFXCT fits an FPGA-based USB interface when the parallel side is implemented at 16 bits and 30 MHz or eight bits and 60 MHz. Its full-speed USB 2.0 transceiver handles the physical layer, while the FPGA must implement the required protocol and data-transfer behavior. Package placement and differential USB routing remain critical.
What is the difference between CY7C68000-56LFXCT and CY7C68000A-56LFXCT?
The CY7C68000A-56LFXCT is an A-revision member of the same Infineon transceiver family, and both are listed as full-speed USB 2.0 1/1 devices in 56-QFN (8 x 8 mm) packages. A direct substitution still requires checking every electrical limit, timing characteristic, pin connection, and device-revision note in the manufacturer documentation before release.
Is CY7C68000-56LFXCT the same as CY7C68000A-56LFXCT?
The two devices are closely related full-speed USB 2.0 transceivers with the same 56-QFN package class and parallel-interface purpose. They are not automatically interchangeable in every design because the A revision may contain specification or qualification changes. Compare the manufacturer datasheets, especially pin functions, timing, electrical limits, and lifecycle notes, before treating either as a drop-in replacement.
When should I choose CY7C68000-56LFXCT over an A-revision transceiver?
Choose the CY7C68000-56LFXCT when its documented USB 2.0 full-speed operation, 16-/8-bit parallel modes, and 56-QFN footprint satisfy an existing qualified design. Prefer a documented A-revision alternative when a new design needs a specific lifecycle, qualification, or updated device specification. Existing production builds should prioritize exact revision continuity over assuming equivalence.
Can CY7C68000-56LFXCT be used for a USB-to-parallel bridge?
Yes, the CY7C68000-56LFXCT can serve as the physical transceiver in a USB-to-parallel bridge. Its 16-bit/30 MHz mode suits wider parallel datapaths, while the eight-bit/60 MHz mode can simplify interface timing. A bridge controller must still handle enumeration, descriptors, endpoint behavior, and protocol translation because this device provides the USB physical layer.
What is the best drop-in replacement for CY7C68000-56LFXCT?
The closest documented same-family drop-in candidates are the 56-QFN versions of the CY7C68000A and CY7C68001 families. No universally qualified replacement can be declared from the available comparison data alone, so engineers should verify pin assignments, USB timing, voltage limits, clock modes, and package drawings for the exact candidate. Continuity with a previously qualified revision is generally safer than an unqualified substitution.
What can replace CY7C68000-56LFXCT?
The CY7C68000A-56LFXCT is the leading same-package replacement candidate because it is identified as a closely related, full-speed USB 2.0 transceiver in a 56-QFN (8 x 8 mm) package. Confirm that the A revision preserves the required 16-/8-bit modes, 30/60 MHz clocks, power pins, and timing limits before treating it as a drop-in replacement.
Is CY7C68000-56LFXCT in stock and what is its lead time?
Current stock and manufacturing lead time should be confirmed through the Request a Quote form on this page. A current distributor listing does not by itself establish a guaranteed XAIPART inventory position, and the manufacturer lifecycle, minimum order quantity, and date-code availability can change. Submit the required quantity and package details with the request for an allocation response.
Where can I buy CY7C68000-56LFXCT and what is its price?
Use the Request a Quote form on this page to request CY7C68000-56LFXCT pricing, stock confirmation, and an allocation. The form supports an exact 56-QFN order without relying on an aging list price. Include the required quantity, target date, and any date-code or traceable-lot requirements in the request.
What is the lead time for CY7C68000-56LFXCT?
The lead time for CY7C68000-56LFXCT must be confirmed for the requested quantity through the Request a Quote form on this page. Lead time depends on current manufacturer and channel inventory, production scheduling, package allocation, and traceability requirements. The presence of a product listing should not be interpreted as a guaranteed delivery commitment.
What RoHS and REACH compliance applies to CY7C68000-56LFXCT?
The RoHS and REACH status should be confirmed in the current manufacturer product documentation or the quote response because the available technical excerpt does not state either declaration. Use the Request a Quote form when a compliance certificate, material declaration, or date-lot-specific environmental document is required for procurement.

נתוני עזר הנדסיים עבור CY7C68000-56LFXCT — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose CY7C68000-56LFXCT for a new or existing design that specifically requires a full-speed USB 2.0 1/1 transceiver with a 16-bit/30 MHz or eight-bit/60 MHz parallel interface and a 56-QFN footprint. Prefer CY7C68000A-56LFXCT when its documented revision-specific electrical, timing, qualification, or lifecycle characteristics provide a defined advantage over the base revision. Consider CY7C68000A-56LFXC or CY7C68001-56LTXC only after checking the exact pin assignments, USB timing, voltage limits, and interface behavior. CY7C68001-56LFXCT is a same-family candidate, but it carries less direct cross-reference support and therefore needs stricter qualification. For production continuity, retaining the exact qualified revision is usually safer than assuming that a similar package and function guarantee drop-in operation.

השוואה עם חלופות

פרמטר מוצר זה CY7C68000A-56LFXCT CY7C68000A-56LFXC CY7C68001-56LTXC CY7C68001-56LFXCT
Brand Infineon Technologies Infineon Technologies Infineon Technologies Infineon Technologies Infineon Technologies
Package 56-QFN (8x8) 56-QFN (8x8) 56-QFN (8x8) 56-QFN (8x8) 56-QFN (8x8)

מבדילים עיקריים

  • Selectable parallel width and clock combination (לעומתCY7C68000A-56LFXCT)
  • Established base revision for continuity (לעומתCY7C68001-56LFXCT)
  • Single-package transceiver integration (לעומתCY7C68000A-56LFXC)

הערות תכנון

Route the USB differential pair as a controlled-impedance, tightly coupled pair with symmetric geometry and no intervening layer changes. Keep the pair short and provide a continuous ground reference beneath it. Place the transceiver close to the USB connector or board entry point so common-mode noise and ESD transients are not distributed through sensitive functional areas.

Place input, output, and bypass capacitors close to their associated package pins using the shortest practical traces. Follow the manufacturer land pattern for the 56-QFN exposed pad and connect the thermal pad to the required ground and copper area. Verify paste, solder mask, and assembly clearance because the library does not contain a dedicated 56-QFN footprint.

Design the parallel side around the selected operating mode: 16 bits at 30 MHz or eight bits at 60 MHz. In the eight-bit configuration, data and clock skew become more significant even though the package is unchanged. Maintain matched output timing at the controller or FPGA, avoid stubs, and review the manufacturer interface timing limits before selecting component tolerances or board-routing assumptions.

Do not treat a matching 56-QFN package as proof of interchangeability. Before substituting an A-revision or CY7C68001-family device, compare every pin name, supply requirement, clock input, timing parameter, USB electrical characteristic, and exposed-pad connection. Preserve the exact revision in new production designs unless the manufacturer explicitly approves the change.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

The available product information does not state the requested environmental or automotive compliance declarations. Request current compliance documentation through the Request a Quote form.

הנתונים אומתו בתאריך: 2026-11-10 — נתונים אומתו ונערכו על ידי צוות הנדסת הרכיבים של XAIPART

חיפושים קשורים

CY7C68000-56LFXCT datasheet CY7C68000-56LFXCT pinout CY7C68000-56LFXCT datasheet pdf Infineon CY7C68000-56LFXCT CY7C68000-56LFXCT equivalent CY7C68000-56LFXCT replacement CY7C68000-56LFXCT drop-in CY7C68000-56LFXCT 56-QFN CY7C68000-56LFXCT USB 2.0 CY7C68000-56LFXCT 16-bit 30 MHz CY7C68000-56LFXCT USB-to-parallel CY7C68000-56LFXCT FPGA interface CY7C68000-56LFXCT vs CY7C68000A-56LFXCT CY7C68000-56LFXCT price CY7C68000-56LFXCT stock

רכיבים ומונחים קשורים

Infineon Technologies CY7C68000-56LFXCT CY7C68000A-56LFXCT CY7C68000A-56LFXC CY7C68001-56LTXC CY7C68001-56LFXCT USB 2.0 full-speed USB USB transceiver USB interface IC serial/deserializer UTMI parallel interface 1/1 transceiver 56-QFN QFN family surface mount SMD 16-bit interface 8-bit interface 30 MHz clock 60 MHz clock FPGA USB-to-parallel bridge differential USB signaling
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר