CY8C3445LTI-086 - 50MHz 8051 MCU | Infineon Technologies
N.º de pieza: CY8C3445LTI-086 ✓ ActivoCY8C3445LTI-086 Descripción general
A microcontroller is a programmable semiconductor that integrates a processing core, memory, and peripherals into one device. The 8051 architecture is an established 8-bit embedded-control platform, while PSoC 3 expands the concept with programmable resources alongside conventional digital control. Within the broader semiconductor hierarchy, this device belongs to the MCU and embedded-controller category rather than a general-purpose microprocessor or DSP.
The principal features visible in the manufacturer datasheet are the 50 MHz operating frequency, 32 KB flash memory organized as 32K by 8 bits, and broad 1.71 V to 5.5 V operating-voltage range. The 68-VFQFN package uses an exposed pad to support heat transfer from the device to the PCB. These characteristics make the MCU suitable for compact control boards, human-interface controllers, and embedded systems that need an 8-bit processor without a large external memory array.
The CY8C3445LTI-086 belongs to the CY8C34xx microcontroller group, identified in the part description as an 8051 PSoC 3 device. Its flash-based program memory supports firmware storage in the same package as the controller. The exposed-pad construction is especially relevant in compact industrial and consumer products because thermal performance depends on the PCB copper area and solder mask layout rather than on a separate heatsink.
Typical application areas include industrial keypad and panel controls, compact sensor-hub controllers, appliance interface boards, LED control systems, and general embedded automation modules. The 50 MHz clock rate provides useful headroom for interrupt-driven control and peripheral coordination, while the 32 KB flash capacity is suitable for moderate firmware sizes. Designers should confirm peripheral availability, pin multiplexing, memory-map behavior, and programming requirements against the exact datasheet before releasing a PCB.
Layout planning should prioritize a continuous ground plane, short return paths for high-frequency signals, and adequate copper beneath the exposed pad. Input and output traces connected to external sensors or actuators should be kept away from sensitive clock and programming nets. Firmware development also depends on the supported programming and debug interface, so schedule device configuration, boot behavior, and peripheral initialization early in the design cycle.
This page consolidates the device identity, package information, technical specifications, sourcing guidance, compatible family options, and practical design considerations into one engineering reference. It also distinguishes documented parameters from items that require confirmation with the Infineon datasheet, helping designers identify PCB and firmware decisions that must be validated before production.
Alternativas directas para CY8C3445LTI-086 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con CY8C3445LTI-086 (mismo factor de forma y huella) — difiere en Package, Product Type.
CY8C3445LTI-081
✅ Sustitución directaConsulte el precio
Ver hoja de datos →CY8C3445LTI-079
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
CY8C3445LTI-086 Valores máximos y características eléctricas
| Product Type | 8-bit microcontroller |
| Processor Architecture | 8051 |
| Product Family | CY8C34xx PSoC 3 |
| Frecuencia de reloj máxima | 50 MHz |
| Flash Memory Size | 32 KB |
| Flash Memory Organization | 32K x 8 bits |
| Operating Voltage Range | 1.71 V to 5.5 V |
| Encapsulado | 68-VFQFN (8 mm x 8 mm) |
| Thermal Pad | Exposed pad |
| Tipo de montaje | Surface mount |
Guía de configuración de pines de CY8C3445LTI-086 68-vfqfn (8 mm x 8 mm)
Configuración de pines para CY8C3445LTI-086 (encapsulado 68-vfqfn (8 mm x 8 mm)). Este CI digital incluye GPIO, interfaces de comunicación (UART, SPI, I2C) y pines de alimentación. Consulte la hoja de datos del fabricante para conocer las funciones alternativas de los pines y las opciones de configuración. Esencial para el diseño de sistemas embebidos y el diseño de PCB.
No hay datos detallados de patillaje disponibles para CY8C3445LTI-086.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
CY8C3445LTI-086 es adecuado para 6 aplicacións: Industrial Keypad and Panel Control, Compact Sensor Hub Controller, Appliance Interface Controller, LED Lighting Control, Battery-Powered Monitoring Node, General Embedded Automation Module.
Industrial Keypad and Panel Control
The CY8C3445LTI-086 fits compact industrial keypad and panel controllers because it combines a 50 MHz 8051-compatible core with 32 KB of on-chip flash and a 1.71 V to 5.5 V operating range. The microcontroller can execute scanning, debouncing, illumination control, and communication firmware in one device. Its 68-VFQFN package also leaves more board area available for connectors and power conditioning than a larger leaded package. Use the exposed pad as a thermal and ground path according to the manufacturer layout guidance. Final selection should confirm the LTI temperature limits, applicable peripheral resources, and pin multiplexing for the intended panel interface.
Recomendado
Compact Sensor Hub Controller
The CY8C3445LTI-086 is suitable for a compact sensor hub that must acquire, filter, and forward measurements from several sensors. Its 50 MHz maximum clock provides timing margin for interrupt-driven sampling and protocol handling, while 32 KB of flash provides room for configuration data and embedded firmware. The 1.71 V to 5.5 V supply range permits integration with compatible low-voltage sensor interfaces. Place the MCU and its supporting passive components close together to limit susceptibility to noise on measurement inputs. The engineer must also verify the exact ADC, comparator, timer, and communication resources before assigning sensors to specific pins.
Recomendado
Appliance Interface Controller
The CY8C3445LTI-086 can serve as the local controller in an appliance interface board that coordinates buttons, indicators, relays, and a communications link. Its 8051-compatible architecture supports straightforward event-driven firmware, and the 32 KB flash capacity is appropriate for moderate control code without an external program-memory device. Operating from 1.71 V to 5.5 V provides design flexibility for mixed-voltage power trees. Keep relay-driver traces separated from sensitive control signals and provide the required protection against inductive transients. Confirm that the selected suffix supports the appliance's ambient temperature and that every used peripheral is available in the exact device configuration.
Recomendado
LED Lighting Control
The CY8C3445LTI-086 is applicable to LED lighting controllers that require deterministic timing, local effect storage, and user-interface handling. Its 50 MHz maximum clock allows software PWM and communication routines to coexist, while 32 KB of flash can store lighting scenes, calibration tables, and control logic. The compact 68-VFQFN footprint supports space-constrained luminaires, although continuous current loading should be kept outside the MCU package where possible. Use exposed-pad copper to improve thermal transfer and follow the manufacturer's recommended stack-up and land pattern. Verify the exact PWM-capable outputs, timing channels, and maximum operating limits before finalizing the LED board.
Recomendado
Battery-Powered Monitoring Node
The CY8C3445LTI-086 can support a small monitoring node when the design can operate within its documented 1.71 V to 5.5 V range and relies on periodic wake-up behavior. The 50 MHz maximum clock allows the firmware to complete sensor sampling and data packing quickly, reducing the portion of time the processor remains active. Its 32 KB flash stores application code and calibration information without an external memory package. Battery designs should still evaluate every peripheral's sleep behavior, regulator quiescent current, and wake-up timing. Select the correct power architecture and use the exposed pad to maintain stable junction temperature under the enclosure's thermal conditions.
Recomendado
General Embedded Automation Module
The CY8C3445LTI-086 works well as the central controller in a general embedded automation module combining digital inputs, outputs, status indicators, and a host interface. Its 50 MHz 8051-compatible processing core is suitable for deterministic control loops, and 32 KB of flash provides sufficient capacity for a compact application without external storage. The 68-VFQFN package reduces board footprint but requires careful land-pattern and reflow control. Use a continuous ground reference, route fast interfaces away from exposed connector edges, and validate the exposed-pad thermal design under maximum processor activity. Peripheral assignment and interrupt priorities must be checked against the device's pin multiplexing and electrical limits.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para CY8C3445LTI-086 — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | CY8C3445LTI-081 | CY8C3445LTI-079 |
|---|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| Package | 68-VFQFN (8 mm x 8 mm) | 68-VFQFN | 68-VFQFN |
| Processor Architecture | 8-bit 8051 | 8-bit 8051 | 8-bit 8051 |
| Product Family | CY8C34xx PSoC 3 | CY8C34xx PSoC 3 | CY8C34xx PSoC 3 |
| Flash Memory Size | 32 KB | 32 KB | 32 KB |
| Exposed Pad | Yes | Yes | Yes |
Diferenciadores clave
- Higher documented clock capability within the same LTI family (frente a CY8C3445LTI-081)
- Established 8051 software compatibility and integrated flash (frente a CY8C3445LTI-079)
- Compact exposed-pad package supports dense embedded boards (frente a CY8C3445LTI-081)
Notas de diseño
Treat the 68-VFQFN exposed pad as a thermal and electrical land rather than as an optional copper feature. Place it over a continuous ground plane according to the Infineon package guidance, minimize thermal interruptions beneath the pad, and use the maximum PCB copper area allowed by the board construction. Validate junction temperature with the actual enclosure, airflow, switching activity, and ambient conditions because the processor's 50 MHz operation can make clock-related power dissipation more significant than the standby load.
Use the manufacturer's land pattern and pin-description table when assigning all 68 VQFN leads and the exposed pad. Keep programming signals, clock routing, and sensitive inputs away from noisy external connectors. Place decoupling capacitors at the supply pins with short, low-loop ground returns, and avoid routing fast or switching nodes beneath the exposed-pad area. A conventional QFN footprint must not be assumed without checking body size, lead pitch, pad dimensions, and exposed-pad construction.
Do not assume that every CY8C3445LTI suffix is electrically interchangeable. Confirm the ordering table for clock rate, temperature grade, qualification, flash configuration, and any device-specific limitations before substituting CY8C3445LTI-081 or CY8C3445LTI-079. Also verify the programming voltage, boot configuration, security settings, and ISP sequence. A mechanically matching package alone does not establish that existing firmware and production-test procedures remain unchanged.
Design the supply path for the documented 1.71 V to 5.5 V operating range and ensure transient control at every operating condition. Place bulk and local ceramic decoupling according to the datasheet recommendations, use a quiet source for sensitive measurement circuits, and characterize startup in the complete power tree. Because the device supports clock frequencies up to 50 MHz, verify that regulator bandwidth and supply ripple remain acceptable for the enabled clock and analog peripherals.
Información de cumplimiento
The current manufacturer material-declaration records for this exact ordering code must be reviewed before making a compliance claim. AEC-Q100 is recorded as not applicable because the part description does not identify it as an automotive-qualified variant.