LM2902N-MAND - 26V 1MHz Quad Op Amp | Texas Instruments
N.º de pieza: LM2902N-MAND ✓ ActivoLM2902N-MAND Descripción general
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. The quad operational amplifier belongs to the broader hierarchy of operational amplifier, analog amplifier, analog signal-processing IC, and semiconductor. Its four independent channels make one package practical for buffering, amplification, active filtering, comparators, instrumentation stages, and control loops that require several similar analog functions.
The principal family-level characteristics are a 26 V maximum supply rating, 1 MHz unity-gain bandwidth, four amplifier circuits, and a 14-pin PDIP package. Push-pull output capability supports output swing above the negative supply rail under suitable load conditions. These characteristics are especially useful in industrial equipment where a higher supply rating and low-cost general-purpose amplification can simplify the power architecture.
Each amplifier uses internal frequency compensation, eliminating the need for an external compensation network in typical closed-loop configurations. The same basic amplifier can be used as a non-inverting stage with high input impedance, an inverting stage with a defined gain, or a voltage follower for buffering. With a 1 MHz gain-bandwidth product, practical closed-loop bandwidth depends on the selected noise gain, while stability and output behavior must be evaluated with the actual load and supply conditions.
Typical uses include sensor interfaces, transducer signal conditioning, active analog filters, industrial controls, audio preamplification, feedback networks, and general signal conditioning. The wide supply range permits operation from industrial 24 V systems when the total supply remains within the 26 V rating, while lower-supply operation supports lower-energy systems. Four channels can reduce package count when the circuit contains multiple independent analog paths.
Designers should verify the exact suffix-specific ordering information, operating-temperature grade, and pin marking before production release. Decoupling capacitors should be placed close to the supply pins, signal traces should avoid nearby switching nodes, and unused amplifier channels should be configured according to the manufacturer guidance rather than left floating. Input and output voltage, current, stability, and common-mode limits must be checked at the intended supply voltage.
This product page combines the manufacturer product identity, verified distributor information, package-level details, drop-in sourcing options, and application guidance. It also highlights the practical trade-offs between the family-level LM2902N and other quad operational amplifiers, helping engineers evaluate PCB reuse, supply-voltage tolerance, bandwidth, sourcing, and functional fit before finalizing a bill of materials.
Alternativas directas para LM2902N-MAND — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con LM2902N-MAND (mismo factor de forma y huella).
LM2902N
✅ Sustitución directaConsulte el precio
Ver hoja de datos →LM2902N
✅ Sustitución directaConsulte el precio
Ver hoja de datos →LM2902N
✅ Sustitución directaConsulte el precio
Ver hoja de datos →LM2902N
✅ Sustitución directaConsulte el precio
Ver hoja de datos →LM2902N
✅ Sustitución directaConsulte el precio
Ver hoja de datos →LM2902N-MAND Valores máximos y características eléctricas
| Product Type | Quad operational amplifier |
| Number of Amplifier Circuits | 4 circuits |
| Maximum Supply Voltage | 26 V |
| Unity-Gain Bandwidth | 1 MHz |
| Tipo de salida | Push-pull |
| Application Category | General-purpose instrumentation and signal conditioning |
| Encapsulado | 14-pin PDIP |
| Recuento de pines | 14 pins |
| Tipo de montaje | Through-hole |
| Compensation | Internally frequency compensated |
| Supply Configuration | Single supply or split supply |
Configuración de pines de LM2902N-MAND
| Pin 1 | OUT1 — Amplifier 1 output |
| Pin 2 | -IN1 — Amplifier 1 inverting input |
| Pin 3 | +IN1 — Amplifier 1 non-inverting input |
| Pin 4 | V+ — Positive supply connection |
| Pin 5 | +IN2 — Amplifier 2 non-inverting input |
| Pin 6 | -IN2 — Amplifier 2 inverting input |
| Pin 7 | OUT2 — Amplifier 2 output |
| Pin 8 | OUT3 — Amplifier 3 output |
| Pin 9 | -IN3 — Amplifier 3 inverting input |
| Pin 10 | +IN3 — Amplifier 3 non-inverting input |
| Pin 11 | V- — Negative supply or ground connection |
| Pin 12 | +IN4 — Amplifier 4 non-inverting input |
| Pin 13 | -IN4 — Amplifier 4 inverting input |
| Pin 14 | OUT4 — Amplifier 4 output |
Aplicaciones típicas
LM2902N-MAND es adecuado para 6 aplicacións: Industrial Sensor Signal Conditioning, Active Analog Filters, Audio Preamplification and Buffering, Power Supply Feedback Control, Data Acquisition and Instrumentation, Motor and Control-System Interfaces.
Industrial Sensor Signal Conditioning
LM2902N-MAND fits industrial sensor interfaces that require several low-frequency conditioning stages on one board. Its four internally frequency-compensated amplifiers can amplify, invert, filter, and buffer sensor signals while the associated LM2902 family operates from a supply rated up to 26 V. That 26 V rating is relevant to 24 V industrial control systems because it can support conventional industrial rails, although the exact suffix-specific limits must be checked. With a 1 MHz unity-gain bandwidth, the device is most appropriate for slow sensor signals and control loops rather than wideband instrumentation. Use one channel for the primary amplifier and the others for filtering or reference buffering, while keeping input common-mode voltage and output swing within the manufacturer limits.
Recomendado
Active Analog Filters
The LM2902N-MAND can implement multiple active-filter sections in audio, control, and measurement equipment. Its four independent, internally compensated operational amplifiers allow Sallen-Key or state-variable topologies to be assembled without separate amplifier packages. The family-level 1 MHz unity-gain bandwidth provides useful loop gain for filters with moderate frequency requirements, while the 26 V supply rating accommodates higher-voltage industrial signal chains. Component tolerances and the amplifier gain-bandwidth relationship determine the attainable cutoff frequency and phase margin. Confirm noise-gain stability, output loading, and supply headroom for each filter section. The device is especially suitable for low-frequency active filters where simplicity and multi-channel integration matter more than the very high bandwidth or low noise of a precision amplifier.
Recomendado
Audio Preamplification and Buffering
LM2902N-MAND is appropriate for general-purpose audio preamplification, input buffering, and level conditioning when four related analog channels are required. Its push-pull outputs and 26 V family supply capability allow operation from higher-voltage headroom-oriented analog rails, subject to the exact device limits. The 1 MHz unity-gain bandwidth is well above the audible range and ample for ordinary audio conditioning, though it does not imply low-noise or high-fidelity performance. Each channel can follow a non-inverting topology for signal gain or an inverting topology when channel inversion is useful. Avoid using it for demanding low-noise microphone preamplification without first checking input bias current, offset voltage, and noise. The main benefit is consolidating several standard audio analog stages into one 14-pin package.
Recomendado
Power Supply Feedback Control
LM2902N-MAND can support error-amplifier, feedback, and supervisory functions in linear power-supply and control-system designs. Four channels permit use of a main error amplifier alongside current-limit, auxiliary feedback, or monitoring paths. The LM2902 family's 26 V maximum supply rating is useful for 24 V industrial power systems, while single- or split-supply operation supports different feedback arrangements. The 1 MHz unity-gain bandwidth allows response to control-loop errors well beyond typical slow power-supply dynamics, but loop compensation still governs stability. Place the feedback-divider output close to the amplifier input, keep high-current switching paths away from the feedback node, and verify saturation and slew requirements during startup and load transients. This application requires careful stability analysis rather than relying on bandwidth alone.
Recomendado
Data Acquisition and Instrumentation
LM2902N-MAND is useful in moderate-speed data-acquisition front ends where several analog channels require common amplification and buffering. The four amplifiers can condition outputs from sensors, transducers, dividers, or analog switches before conversion. A 1 MHz unity-gain bandwidth supports signal paths well above conventional low-frequency process measurements, while the 26 V family rating can simplify interface to 24 V test equipment. The amplifier is not inherently a precision part, so offset voltage, bias current, input bias errors, and common-mode range must be evaluated against the measurement accuracy budget. Use a grounded or differentially referenced topology appropriate to the source, provide local supply bypassing, and keep high-impedance input traces short. This device is most appropriate when general-purpose accuracy and cost matter more than micropower operation.
Recomendado
Motor and Control-System Interfaces
LM2902N-MAND can condition feedback and reference signals in industrial motor-control and electromechanical systems. Four channels can handle position feedback, command scaling, current-sense amplification, and error comparison within a 24 V control environment. The associated LM2902 family's 26 V supply rating accommodates conventional industrial rails with design margin, and its 1 MHz bandwidth is ample for many low-bandwidth control loops. Use the amplifier only where its input and output ranges support the sensed signal and excitation waveform; motor transients can exceed nominal rail limits even when the average supply is 24 V. Add appropriate protection, keep feedback routing away from switching nodes, and verify that each amplifier remains stable with the real load. The main advantage is consolidating multiple general-purpose analog functions without changing the through-hole package style.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para LM2902N-MAND — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | LM2902N | LM2902N | LM2902N | LM2902N | LM2902N |
|---|---|---|---|---|---|---|
| Package | 14-pin PDIP | 14-pin PDIP | 14-pin DIP | 14-pin DIP | 14-pin DIP | 14-pin DIP |
| Brand | Texas Instruments | Texas Instruments | STMicroelectronics | National Semiconductor | HGSEMI | Intersil |
| Amplifier Count | 4 | 4 | 4 | 4 | 4 | 4 |
| Application Class | General-purpose instrumentation and signal conditioning | General-purpose instrumentation and signal conditioning | General-purpose instrumentation and signal conditioning | General-purpose instrumentation and signal conditioning | General-purpose instrumentation and signal conditioning | General-purpose instrumentation and signal conditioning |
Diferenciadores clave
- Four general-purpose amplifiers consolidated in one through-hole package (frente a LM324N)
- Higher family supply-voltage ceiling (frente a LM324N)
- Established 14-pin family footprint supports second sourcing (frente a STMicroelectronics LM2902N)
- Single-package channel consolidation (frente a STMicroelectronics LM2902N)
Notas de diseño
Treat the 26 V figure as an absolute family-level ceiling, not a recommended operating rail. For a nominal 24 V industrial supply, include regulator tolerance, load transients, startup overshoot, and temperature effects in the worst-case analysis. Place local supply bypass capacitors close to pins 4 and 11, and follow the capacitor values and layout guidance in the manufacturer datasheet. Decoupling requirements can change with gain, source impedance, and operating frequency.
Do not assume that every amplifier channel may be left unused. Configure each unused channel as a voltage follower with its output tied to its inverting input, connect the non-inverting input to a valid common-mode reference within the permitted range, and confirm the output remains stable. Also check the input common-mode range at the actual supply voltage; a 26 V maximum supply rating does not imply that every input can swing across the complete rail range.
Route high-impedance input and feedback traces away from switching-node copper, inductors, relay contacts, and other sources of injected noise. Keep feedback loops compact and connect the bypass return path directly to the relevant ground or supply pin. Because this is a through-hole 14-pin DIP, use a socket only when its pin contacts and insulation can preserve reliable electrical and mechanical performance at the operating temperature.
Use the 1 MHz unity-gain bandwidth as the starting point for gain-bandwidth planning, not as an unconditional operating-frequency limit. Closed-loop bandwidth decreases as noise gain rises, and capacitive loading can reduce stability. Add isolation resistors when driving long cables, sampled sensor outputs, or large capacitive loads, and verify the resulting response with oscilloscope measurements before production release.
Información de cumplimiento
The Texas Instruments LM2902-N product page is the authoritative source for the exact suffix's environmental and qualification information. No specific compliance declaration is stated for LM2902N-MAND in the manufacturer-page snippets.