LM2903HYDT - Dual 36V Open-Collector Comparator | STMicroelectronics
N.º de pieza: LM2903HYDT ✓ ActivoLM2903HYDT Descripción general
A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM2903HYDT belongs to the comparator hierarchy within analog ICs and interface ICs. Its two channels can be used independently, with one channel referenced to ground for single-supply operation or both channels operating from positive and negative rails in dual-supply systems. The open-collector output allows the output state to be pulled up to a suitable external voltage.
Key electrical characteristics include a low typical supply current of 0.4 mA, a typical input bias current of 25 nA, and a typical input offset current of ±5 nA. The input common-mode voltage range includes ground, which supports single-supply sensing near 0 V. The open-collector output has a typical low saturation voltage of 250 mV at an output current of 4 mA, while the differential input voltage range equals the maximum rated supply voltage.
The LM2903HYDT combines two differential comparators in one package, reducing board area in designs that require more than one threshold decision. Its low operating current suits battery-operated and low-power monitoring systems. Because the outputs are open collector, applications can select the pull-up voltage independently and can wire multiple open-collector outputs together when wired-AND behavior is required. A pull-up resistor is required for normal high-level output operation.
Typical uses include overvoltage and undervoltage monitoring, industrial sensor thresholds, battery-pack protection, motor-control interfaces, window or level detection, and general-purpose digital thresholding. The two independent channels can monitor different supply rails or implement hysteresis around a reference voltage. For sensitive systems, input bias current, offset voltage, common-mode limits, output leakage, and propagation delay should be checked against the sensing network and logic family.
PCB implementation should keep the comparator inputs away from switching nodes and high-current paths. Place the input resistors and optional hysteresis network close to the associated pins, provide a solid ground return, and route open-collector pull-ups away from sensitive analog inputs. If the input signals can switch rapidly, minimize parasitic capacitance and verify that the external network does not cause input overvoltage during transients.
This page combines the electrical limits, package details, pin assignments, practical application guidance, and confirmed pin-compatible alternatives for the LM2903HYDT. It also identifies the parameters that require verification against the latest STMicroelectronics datasheet before production release or unqualified second-source use.
Alternativas directas para LM2903HYDT — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con LM2903HYDT (mismo factor de forma y huella) — difiere en Comparator Type, Output Type, Package, Automotive Qualification, Operating Temperature Range.
LM2903HD
✅ Sustitución directaConsulte el precio
Ver hoja de datos →LM2903BIDR
✅ Sustitución directaConsulte el precio
Ver hoja de datos →LM2903AVQDRQ1
✅ Sustitución directaConsulte el precio
Ver hoja de datos →LM2903HYDT Valores máximos y características eléctricas
| Comparator Type | Low-power dual differential voltage comparator |
| Number of Channels | 2 channels |
| Supply Voltage Range | 2 V to 36 V |
| Dual-Supply Operating Range | ±1 V to ±18 V |
| Typical Supply Current | 0.4 mA |
| Typical Power Consumption per Comparator | 1 mW at 5 V |
| Typical Input Bias Current | 25 nA |
| Typical Input Offset Current | ±5 nA |
| Input Common-Mode Voltage Range | Includes ground |
| Differential Input Voltage Range | Equal to maximum rated supply voltage |
| Tipo de salida | Open-collector, rail-to-rail |
| Typical Low Saturation Voltage | 250 mV at 4 mA output current |
| Propagation Delay | 1.3 µs |
| Encapsulado | 8-pin SOIC |
| Tipo de montaje | Surface mount |
| Packaging | Tape and reel |
| Automotive Qualification | AEC-Q100 qualified |
Configuración de pines de LM2903HYDT
| Pin 1 | OUT1 — Comparator 1 open-collector output |
| Pin 2 | IN1- — Comparator 1 inverting input |
| Pin 3 | IN1+ — Comparator 1 non-inverting input |
| Pin 4 | VCC- — Ground connection |
| Pin 5 | IN2+ — Comparator 2 non-inverting input |
| Pin 6 | IN2- — Comparator 2 inverting input |
| Pin 7 | OUT2 — Comparator 2 open-collector output |
| Pin 8 | VCC+ — Positive supply connection |
Aplicaciones típicas
LM2903HYDT es adecuado para 6 aplicacións: Battery Overvoltage and Undervoltage Detection, Industrial Sensor Threshold Conditioning, Automotive Supply Rail Supervision, Motor and Actuator Control Interface, Window and Level Limit Detection, Low-Power Monitoring and Alarm System.
Battery Overvoltage and Undervoltage Detection
The LM2903HYDT fits battery-protection circuits because its two differential channels can monitor separate voltage thresholds while operating from a 2 V to 36 V supply range. A resistor-divider network can scale each battery rail into the common-mode input range, while the comparators produce open-collector fault signals for a charger or controller. Its typical 0.4 mA supply current is useful in portable systems. Design the dividers around the 25 nA typical input bias current and check the 1.3 µs propagation delay against the protection response time. A pull-up resistor establishes each digital fault level, and hysteresis can prevent repeated switching when the battery voltage changes near a threshold.
Recomendado
Industrial Sensor Threshold Conditioning
The LM2903HYDT is useful for converting a scaled sensor or process voltage into a logic decision. Its differential inputs allow a sensor signal to be compared with a reference, and the two channels can support two related thresholds or complementary conditions. The common-mode input range includes ground, which helps with signals near the lower rail, while the 36 V maximum supply gives useful headroom in industrial systems. The low saturation voltage of 250 mV typical at 4 mA helps drive a pull-up load without a separate buffer. Apply input filtering carefully so excessive capacitance does not distort the 1.3 µs propagation delay or encourage oscillation around the decision point.
Recomendado
Automotive Supply Rail Supervision
The LM2903HYDT is appropriate for automotive rail supervision because the part is identified with AEC-Q100 qualification and combines two differential channels in an 8-pin SOIC package. Each channel can monitor a divided 12 V, 24 V, or other vehicle rail and assert an open-collector fault signal when the voltage crosses its configured limit. The 2 V to 36 V operating range supports several vehicle electrical systems. Engine-bay placement still requires careful attention to transient protection, grounding, and wiring because logic qualification does not remove external automotive surge requirements. Use the manufacturer electrical limits to define resistor ratings and protection components, and verify the exact temperature grade for the production vehicle program.
Recomendado
Motor and Actuator Control Interface
The LM2903HYDT can form the decision stage between a motor or actuator sensor and a control input. Its differential inputs support comparison of a position, speed, or current-sense signal against a reference, while the open-collector output can pull down a gate-driver or logic input. The 36 V supply capability is useful for powered industrial systems, and the low typical supply current of 0.4 mA reduces control overhead. Add hysteresis with positive feedback when the monitored signal has noise near the threshold. Because the output can sink rather than source current, choose a pull-up voltage compatible with the driven interface and verify that the connected device accepts the output's voltage and timing characteristics.
Recomendado
Window and Level Limit Detection
The LM2903HYDT can implement digital upper and lower limits for a potentiometer, liquid-level sensor, or position element. One channel can detect the upper boundary and the other the lower boundary, allowing two open-collector signals to feed a controller or indicator. The differential-input architecture helps reject common voltage offsets shared by the sensed signal and reference. For a resistive sensor, account for the 25 nA typical input bias current and ±5 nA typical input offset current when selecting resistor values. Add deliberate hysteresis to slow movement or sensor noise near each limit, and use separate pull-up resistors if the two output states require independent logic levels.
Recomendado
Low-Power Monitoring and Alarm System
The LM2903HYDT suits low-power monitoring systems because two comparator channels share one package and the typical supply current is only 0.4 mA. The channels can watch a sensor rail and a status line, or form a window comparator around an analog measurement. Its open-collector outputs are practical for driving an alarm or microcontroller interrupt when combined with pull-up resistors. The common-mode range including ground supports monitoring near zero volts, while the 36 V maximum operating voltage covers many industrial rails. Define the alarm thresholds using the input offset and sensor accuracy, then add hysteresis to prevent chatter. Ensure that leakage in long wiring or high-impedance sensor networks does not shift the intended threshold.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para LM2903HYDT — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | LM2903HD | LM2903BIDR | LM2903AVQDRQ1 |
|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Comparator Configuration | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator |
Diferenciadores clave
- AEC-Q100-qualified dual-comparator option in a standard 8-pin SOIC footprint (frente a LM2903HD)
- Two independent 36 V-capable comparison channels in one package (frente a LM2903BIDR)
- Low 0.4 mA typical supply consumption for dual thresholding (frente a LM2903AVQDRQ1)
Notas de diseño
Do not treat the open-collector outputs as actively driven high outputs. Install a pull-up resistor on each output, and select its voltage within the comparator output ratings and the driven logic family's requirements. Multiple open-collector outputs can share a pull-up when wired-AND behavior is intended, but this also ties their fault states together and can create an unintended combined load.
Keep the two input pairs short and away from switching nodes, motor traces, and high-current return paths. Connect the ground pin to a low-impedance ground plane, place optional input and hysteresis resistors close to the relevant pins, and route output pull-ups away from sensitive analog inputs. For high-impedance sensor networks, account for the 25 nA typical input bias current and input leakage when estimating threshold error.
Add hysteresis when the input signal can cross the threshold slowly or contains noise; positive feedback from OUT1 to IN1+ and OUT2 to IN2+ creates separated switching levels. Size the feedback network around the input offset, output saturation, and pull-up resistance. Confirm that the 1.3 µs typical propagation delay is acceptable and that input-node capacitance does not cause excessive delay or oscillation.
Información de cumplimiento
The LM2903HYDT is identified as AEC-Q100 qualified. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer compliance documentation.