onsemi

LM2904ANG - Dual 8-PDIP General-Purpose Op Amp | onsemi

N.º de pieza: LM2904ANG ✗ Fin de vida
Single or split supply Vdss 8-PDIP, 0.300 inch pitch (7.62 mm) Package
MOQ: 1 |

LM2904ANG Descripción general

The onsemi LM2904ANG is a dual, general-purpose operational amplifier packaged in an 8-pin plastic DIP. It provides two amplifier circuits per package, a 0.6 V/µs slew rate, and a 1 MHz gain-bandwidth product. The device supports single-supply or split-supply operation and has a common-mode input range that extends toward ground or VEE, making it suitable for conventional industrial and signal-conditioning circuits.

An operational amplifier is a high-gain, low-output-impedance active device used to amplify voltage differences between two inputs. The LM2904 family belongs to the broader analog IC hierarchy of operational amplifiers, linear amplifiers, and analog signal-conditioning ICs. Its dual construction allows two independent amplifier channels in one package, reducing board area in designs that require multiple analog signal paths.

The principal characteristics include two integrated circuits, a general-purpose amplifier architecture, a 0.6 V/µs slew rate, and a 1 MHz gain-bandwidth product. The common-mode input capability extending to ground or VEE is important for single-supply designs because it permits the amplifier to process input signals near the lower supply rail. Low power drain also makes the device suitable for battery-operated and low-power equipment when appropriately configured.

The LM2904ANG is designed for general-purpose applications rather than precision or high-speed signal processing. Its 1 MHz gain-bandwidth product is adequate for audio, sensing interfaces, control loops, and low-frequency analog amplification. Because the device is listed as obsolete, engineers should also evaluate current-family alternatives when new production designs require an active lifecycle product.

Typical uses include dual-stage sensor conditioning, low-frequency active filters, industrial control signal amplification, audio preamplification, and generic voltage-feedback stages. In each circuit, feedback components establish the closed-loop gain, while the supply rails and input common-mode range must remain within the operating conditions specified by the manufacturer.

A practical design consideration is input bias-current compensation. The manufacturer documentation should be consulted for the recommended source impedance and compensation arrangement, particularly when driving low-impedance sources. PCB layout should keep feedback loops short and provide adequate ground-return paths to prevent additional noise or instability.

This product page combines the LM2904ANG electrical characteristics, package information, lifecycle status, comparison data, and practical replacement guidance. It also identifies pin-compatible options for obsolete designs while helping engineers distinguish between a true board-level replacement and a merely similar amplifier.

Alternativas directas para LM2904ANG — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con LM2904ANG (mismo factor de forma y huella) — difiere en Package, Supply Configuration, Gain-Bandwidth Product, Amplifier Type, Common-Mode Input Range.

Texas Instruments
Package: 8-pin PDIP
Supply Configuration: Single supply or split supply
Common-Mode Input Range: Extending to ground/VEE
Comparar con LM2904ANG →
Texas Instruments
Package: 8-pin PDIP
Supply Configuration: Single supply
Gain-Bandwidth Product: 700 kHz
Comparar con LM2904ANG →
Texas Instruments
Package: 8-pin mini-DIP or 8-pin PDIP, depending on manufacturer source
Supply Configuration: Single supply operation emphasized in the verified LM358 family description
Comparar con LM2904ANG →

LM2904NG

✅ Sustitución directa
onsemi
📦 8-PDIP
General Purpose · 2 · 1 MHz · 0.6 V/µs · 3 V to 26 V · -40C to +105C · PDIP-8 (0.300 in, 7.62 mm) · Through Hole

Consulte el precio

Ver hoja de datos →

LM2904N

✅ Sustitución directa
Texas Instruments
📦 8-PDIP
2 amplifiers · 26 V · 1 MHz · Dual independent operational amplifiers · Internally frequency compensated · Single supply or split supply · Extending to ground/VEE

Consulte el precio

Ver hoja de datos →

LM358N

✅ Sustitución directa
Texas Instruments
📦 8-PDIP
Dual operational amplifier · 2 independent amplifiers · 32 V · 1 MHz · Differential input · Internally frequency compensated · Single supply operation emphasized in the verified LM358 family description · 8-pin mini-DIP or 8-pin PDIP, depending on manufacturer source

Consulte el precio

Ver hoja de datos →

LM358N

✅ Sustitución directa
Texas Instruments
📦 8-PDIP
Dual operational amplifier · 2 independent amplifiers · 32 V · 1 MHz · Differential input · Internally frequency compensated · Single supply operation emphasized in the verified LM358 family description · 8-pin mini-DIP or 8-pin PDIP, depending on manufacturer source

Consulte el precio

Ver hoja de datos →

NJM2904D

✅ Sustitución directa
📦 8-PDIP
LM2904-family dual amplifier in an 8-PDIP package; exact input-offset, bias-current, temperature, and common-mode ratings differ by manufacturer and require verification.

📋 Alternativa de referencia (no en el catálogo)

LM2904ANG Valores máximos y características eléctricas

Number of Amplifier Circuits 2 circuits
Amplifier Type General-purpose operational amplifier
Supply Type Single or split supply
Gain-Bandwidth Product 1 MHz
Slew Rate 0.6 V/µs
Common-Mode Input Range Extends to ground/VEE
Power Drain Low
Encapsulado 8-PDIP, 0.300 inch pitch (7.62 mm)
Tipo de montaje Through-hole
Packaging Type Tube
Número de pines 8 pins

Configuración de pines de LM2904ANG

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
Pin 1 OUT1 — Amplifier 1 output
Pin 2 IN1- — Amplifier 1 inverting input
Pin 3 IN1+ — Amplifier 1 non-inverting input
Pin 4 V- — Negative supply or ground connection
Pin 5 IN2+ — Amplifier 2 non-inverting input
Pin 6 IN2- — Amplifier 2 inverting input
Pin 7 OUT2 — Amplifier 2 output
Pin 8 V+ — Positive supply connection

Aplicaciones típicas

LM2904ANG es adecuado para 6 aplicacións: Industrial Sensor Signal Conditioning, Audio Preamplification, Low-Frequency Active Filtering, Power Supply Current Monitoring, Generic Voltage Amplification, Legacy Equipment Repair.

🏭

Industrial Sensor Signal Conditioning

The LM2904ANG can condition low-frequency sensor signals where two channels provide independent amplification or buffering on a controller board. Its dual-amplifier organization, 1 MHz gain-bandwidth product, and 0.6 V/µs slew rate are suitable for common pressure, temperature, and position interfaces operating well below megahertz bandwidth. The common-mode input range extending toward ground or VEE is particularly useful in single-supply sensor circuits whose signals remain close to the lower rail. Engineers should verify the actual input-offset voltage, input-bias current, and allowable source impedance for the selected sensor. Feedback resistors should be placed close to the amplifier, and the circuit must retain sufficient supply headroom for the required output voltage and load.

🎧

Audio Preamplification

The LM2904ANG fits low-frequency audio preamplifier stages requiring two signal channels in one 8-PDIP package. Its 1 MHz gain-bandwidth product supports audio-band closed-loop gains when the gain-bandwidth product is not exhausted, while the 0.6 V/µs slew rate provides ample margin for ordinary low-bandwidth audio signals. The common-mode range toward ground or VEE can simplify single-supply headroom planning. Because this is a general-purpose rather than low-noise audio amplifier, system-level noise performance must be evaluated with the chosen resistor values, source impedance, and supply bypass network. Output clipping, load capability, and stability should also be checked before using the device with headphone, line, or mixer stages.

🎛️

Low-Frequency Active Filtering

The LM2904ANG can implement the two amplifier sections needed for a low-frequency active filter or biquad stage. Its 1 MHz gain-bandwidth product provides more open-loop bandwidth than many applications require, while the 0.6 V/µs slew rate limits large-signal transient behavior for precision filter designs. The device is best suited to signal frequencies well below its bandwidth limit, with component tolerances and noise contributing significantly to the overall response. Grounded single-supply operation requires careful biasing so the signal remains inside the amplifier’s common-mode range. Place feedback components close to the relevant pins, maintain symmetrical ground routing, and test the completed filter across its expected input amplitude and frequency range.

⚡

Power Supply Current Monitoring

The LM2904ANG can amplify a scaled voltage representing supply or load current for monitoring and control systems. The dual configuration allows one channel to monitor a power rail while the other handles a related reference or buffered output. The 0.6 V/µs slew rate and 1 MHz gain-bandwidth product are suitable for slow current-loop signals and protection thresholds, and operation from a split supply can simplify measurements around ground. The design must ensure that shunt-amplifier inputs remain within the common-mode range and that the required output does not exceed the output-swing limits. Input filtering, Kelvin routing where applicable, and careful resistor selection help control offset and thermal errors in precision monitoring systems.

🔧

Generic Voltage Amplification

The LM2904ANG is suitable for conventional voltage-feedback amplification when the application does not require modern precision or high-speed performance. Two amplifier channels in one 8-PDIP reduce the number of packages required for a basic analog board, while the 1 MHz gain-bandwidth product supports low- to mid-frequency closed-loop gains. The device accepts single or split supplies, allowing integration into legacy industrial and educational circuits. When using it as a non-inverting stage, calculate the closed-loop gain from the feedback divider and verify that the desired output remains within the available swing. When using it as an inverting stage, account for input bias-current effects and select source and feedback resistors that minimize offset error.

🔧

Legacy Equipment Repair

The LM2904ANG is useful for repairing or maintaining legacy analog equipment that uses an 8-PDIP dual general-purpose operational amplifier. Its two-circuit configuration and through-hole package make it practical where a board-level replacement is preferable to redesigning the surrounding analog section. The obsolete lifecycle status makes exact footprint, pinout, supply, and temperature verification essential before substitution. Maintenance teams should compare the replacement’s offset voltage, input-bias current, common-mode range, output swing, and stability behavior with the original device. The original board layout should also be inspected for obsolete components and heat-damaged sockets. A replacement should be tested in the complete circuit rather than judged only by its pin arrangement.

What is the LM2904ANG?
The LM2904ANG is a dual general-purpose operational amplifier in an 8-pin plastic DIP package. It contains two amplifier circuits and supports single-supply or split-supply operation. According to the onsemi LM2904 documentation, the common-mode input voltage range extends toward ground or VEE, while the specified slew rate is 0.6 V/µs and the gain-bandwidth product is 1 MHz.
Where can I download the LM2904ANG datasheet PDF?
The LM2904ANG datasheet is available through the onsemi-hosted documentation listing and the archived manufacturer-document links listed on this page. The document covers the dual-amplifier electrical characteristics, common-mode input range, supply arrangements, package information, and recommended applications. Use the manufacturer PDF when performing design sign-off because third-party mirrors may organize pages differently or omit attachments.
What is the LM2904ANG pinout?
The LM2904ANG uses the conventional 8-pin dual-op-amp DIP pinout: pins 1 and 7 are the two outputs, pins 2 and 6 are inverting inputs, pins 3 and 5 are non-inverting inputs, pin 4 connects to VEE or ground, and pin 8 connects to VCC or positive supply. Confirm the orientation against the package drawing and pin-description table before assigning PCB tracks.
Is the LM2904ANG obsolete?
The LM2904ANG is listed as obsolete in current component-lifecycle information. It can remain relevant for maintenance, repair, and previously approved designs, but new production projects should verify whether an active replacement satisfies the required package, pinout, supply range, electrical limits, and qualification criteria. The manufacturer documentation remains the controlling reference for operating and handling requirements.
What are the key specifications of LM2904ANG that engineers should know?
The main LM2904ANG specifications are two amplifier circuits, a general-purpose design, 0.6 V/µs slew rate, 1 MHz gain-bandwidth product, and operation from a single or split supply. The device also provides a common-mode input range extending toward ground or VEE. These characteristics place it in the low-frequency general-purpose analog amplifier class rather than precision or high-speed families.
Where can I buy LM2904ANG online?
Use the Request a Quote form on this page to request LM2904ANG availability, lot traceability, and a current quotation. Because the LM2904ANG is an obsolete part, stock and order conditions can vary by package form, quantity, and date code. The request should state the required quantity, tube or other delivery format, and any acceptable manufacturer-change or traceability requirements.
What is the price of LM2904ANG?
Current pricing for LM2904ANG should be obtained through the Request a Quote form on this page. The part is obsolete, so a quoted amount may depend on remaining factory stock, lot traceability, package form, and requested quantity. Buyers should also request the date code and packaging information so that inventory can be evaluated against their assembly and inspection requirements.
What is the lead time for LM2904ANG?
Request the current lead time and minimum order quantity through the Request a Quote form on this page. Since the LM2904ANG is obsolete, lead time depends on remaining factory inventory rather than an active production schedule. Include your forecast quantity and required tube packaging when requesting a quotation so the supplier can identify the closest available manufacturing lot.
Is LM2904ANG in stock?
Stock status for LM2904ANG changes as obsolete inventory is allocated. Use the Request a Quote form on this page to request a current availability confirmation rather than relying on a historical inventory count. For maintenance programs, specify the quantity, date-code requirement, and packaging format required by the receiving facility.
LM2904ANG vs LM2904NG - which is better for an existing DIP design?
LM2904ANG and LM2904NG are onsemi LM2904-family options associated with the same 8-pin plastic DIP format, but their exact temperature, grade, or ordering characteristics must be compared before substitution. According to the onsemi ordering information, the suffix identifies package and qualification details. Use the part-specific datasheet to verify operating temperature, electrical ratings, and pin compatibility.
When should I choose LM2904ANG over another dual general-purpose op amp?
Choose LM2904ANG for an existing 8-PDIP design that specifically requires that ordering code, especially during repair or controlled continuation of an approved assembly. For a new design, favor an active device when lifecycle continuity matters. The LM2904ANG’s 1 MHz gain-bandwidth product and 0.6 V/µs slew rate suit low-frequency general-purpose amplification but do not match modern high-speed or precision families.
Is LM2904ANG suitable for audio and sensor-conditioning applications?
Yes, LM2904ANG is suitable for low-frequency audio and sensor-conditioning stages when the circuit operates within its specified supply and common-mode limits. Its 1 MHz gain-bandwidth product and 0.6 V/µs slew rate can handle many general-purpose signal paths, but designers should check noise, offset, bias-current, and output-swing requirements against the individual amplifier channel.
What is the best drop-in replacement for LM2904ANG?
The best replacement is the candidate that matches the 8-pin DIP footprint, pin assignment, amplifier configuration, supply range, input/output swing, and required operating grade. LM2904N-family parts, LM358-type dual amplifiers, and other cross-referenced devices may preserve the board outline, but electrical equivalence must be checked rather than inferred from the package alone. Request lifecycle and traceability details with the quotation.
Can an LM358 replace LM2904ANG?
An LM358-family device can be a candidate only after verifying its 8-pin DIP footprint, pinout, common-mode range, output-swing behavior, stability with the intended feedback network, and load conditions. The LM2904ANG is rated for a 1 MHz gain-bandwidth product and 0.6 V/µs slew rate, but the replacement’s limits and operating-temperature grade must meet the original design requirements.
What is the best onsemi equivalent for LM2904ANG?
The closest onsemi candidate should be selected from the manufacturer’s LM2904 family ordering table by matching the exact package, temperature grade, supply limits, and electrical characteristics. The LM2904NG is a relevant family comparison, but it should not be treated as an automatic substitution. Confirm the suffix-specific datasheet and obtain manufacturer approval when qualification or traceability is required.
What should engineers check when replacing LM2904ANG on a PCB?
Engineers should check the physical row spacing, notch orientation, pin numbering, dual-amplifier pinout, supply pins, input common-mode range, output swing, load capability, and input bias current. For an LM2904ANG replacement, also compare the 1 MHz gain-bandwidth product and 0.6 V/µs slew rate against the original design’s bandwidth and transient requirements. Verify stability with the actual feedback network.

Datos de referencia de ingeniería para LM2904ANG — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose LM2904ANG when maintaining an existing design requires the exact onsemi ordering code, 8-PDIP footprint, dual general-purpose topology, and documented 1 MHz gain-bandwidth and 0.6 V/µs slew-rate characteristics. It is especially practical for legacy industrial, audio, filtering, and sensor-conditioning boards where redesigning the analog section would be costly. Select LM2904NG for a closely related onsemi family option only after confirming the suffix-specific temperature and grade differences. Consider Texas Instruments LM2904N when its 26 V supply rating and current lifecycle position satisfy the circuit, but verify common-mode range, bias current, offset, and output behavior. STMicroelectronics or Texas Instruments LM358N and Renesas NJM2904D may fit the same DIP outline, yet each requires a channel-by-channel comparison of bias current, offset, output swing, supply range, and stability. For new designs, lifecycle continuity should normally outweigh use of an obsolete ordering code.

Comparación con alternativas

Parámetro Este producto LM2904NG LM2904N LM358N LM358N NJM2904D
Brand onsemi onsemi Texas Instruments STMicroelectronics Texas Instruments Renesas Electronics
Package 8-PDIP 8-PDIP 8-PDIP 8-PDIP 8-PDIP 8-PDIP
Mounting Type Through-hole Through-hole Through-hole Through-hole Through-hole Through-hole

Diferenciadores clave

  • Two general-purpose amplifier channels in one through-hole package (frente a LM358N)
  • Established LM2904-family application characteristics (frente a NJM2904D)
  • Single- and split-supply compatibility (frente a LM2904N)

Notas de diseño

Route the two op-amp channels with short feedback paths and keep the inverting-input nodes physically compact to reduce parasitic capacitance and susceptibility to injected noise. Pin 4 is the negative supply or ground connection and pin 8 is the positive supply; provide a low-impedance return path and place bypass capacitors close to the relevant supply pins. The DIP layout should also preserve the manufacturer’s specified notch orientation and pin numbering.

Do not assume that matching the 8-PDIP outline guarantees electrical equivalence. Before substituting a dual amplifier, compare input offset voltage, input-bias current, common-mode range, output swing, output-current capability, supply limits, stability with the selected feedback network, and operating-temperature grade. Single-supply circuits also require verification that the signal and output remain inside the amplifier’s usable input and output ranges.

Check the power-supply range against the exact LM2904ANG ordering-code documentation before energizing the board. The device can operate from a single supply or split supplies, but the positive and negative rails must satisfy the applicable absolute-maximum and operating limits. In battery-powered designs, account for the amplifier’s supply current, output-stage behavior, and the load driven by each channel rather than considering quiescent current alone.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

RoHS and REACH are referenced in cross-reference material, but no definitive compliance result was stated. The LM2904ANG is a general-purpose analog IC and is not identified as an AEC-Q100 automotive-qualified device.

Datos verificados el: 2026-11-13 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

LM2904ANG datasheet LM2904ANG pinout LM2904ANG datasheet pdf LM2904ANG equivalent LM2904ANG replacement LM2904ANG cross reference LM2904ANG price LM2904ANG stock LM2904ANG vs LM2904NG onsemi LM2904ANG LM2904ANG 8-PDIP amplifier LM2904ANG application circuit

Componentes & términos relacionados

onsemi LM2904ANG LM2904NG LM2904N LM358N NJM2904D Texas Instruments STMicroelectronics Renesas Electronics operational amplifier dual op amp general-purpose amplifier analog IC linear amplifier signal-conditioning IC common-mode input range gain-bandwidth product slew rate 8-PDIP DIP package family through-hole mounting surface mount single-supply operation split-supply operation RoHS REACH
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ