LM2904ANG - Dual 8-PDIP General-Purpose Op Amp | onsemi
MPN: LM2904ANG ✗ סוף ייצורLM2904ANG סקירה
An operational amplifier is a high-gain, low-output-impedance active device used to amplify voltage differences between two inputs. The LM2904 family belongs to the broader analog IC hierarchy of operational amplifiers, linear amplifiers, and analog signal-conditioning ICs. Its dual construction allows two independent amplifier channels in one package, reducing board area in designs that require multiple analog signal paths.
The principal characteristics include two integrated circuits, a general-purpose amplifier architecture, a 0.6 V/µs slew rate, and a 1 MHz gain-bandwidth product. The common-mode input capability extending to ground or VEE is important for single-supply designs because it permits the amplifier to process input signals near the lower supply rail. Low power drain also makes the device suitable for battery-operated and low-power equipment when appropriately configured.
The LM2904ANG is designed for general-purpose applications rather than precision or high-speed signal processing. Its 1 MHz gain-bandwidth product is adequate for audio, sensing interfaces, control loops, and low-frequency analog amplification. Because the device is listed as obsolete, engineers should also evaluate current-family alternatives when new production designs require an active lifecycle product.
Typical uses include dual-stage sensor conditioning, low-frequency active filters, industrial control signal amplification, audio preamplification, and generic voltage-feedback stages. In each circuit, feedback components establish the closed-loop gain, while the supply rails and input common-mode range must remain within the operating conditions specified by the manufacturer.
A practical design consideration is input bias-current compensation. The manufacturer documentation should be consulted for the recommended source impedance and compensation arrangement, particularly when driving low-impedance sources. PCB layout should keep feedback loops short and provide adequate ground-return paths to prevent additional noise or instability.
This product page combines the LM2904ANG electrical characteristics, package information, lifecycle status, comparison data, and practical replacement guidance. It also identifies pin-compatible options for obsolete designs while helping engineers distinguish between a true board-level replacement and a merely similar amplifier.
חלופות תחליף ישיר עבור LM2904ANG — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם LM2904ANG (אותו גורם צורה וטביעת רגל) — שונים ב Package, Supply Configuration, Gain-Bandwidth Product, Amplifier Type, Common-Mode Input Range.
LM2904NG
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM2904N
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM358N
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM358N
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←NJM2904D
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
LM2904ANG דירוגים מרביים ומאפיינים חשמליים
| Number of Amplifier Circuits | 2 circuits |
| Amplifier Type | General-purpose operational amplifier |
| Supply Type | Single or split supply |
| Gain-Bandwidth Product | 1 MHz |
| Slew Rate | 0.6 V/µs |
| Common-Mode Input Range | Extends to ground/VEE |
| Power Drain | Low |
| מארז | 8-PDIP, 0.300 inch pitch (7.62 mm) |
| סוג הרכבה | Through-hole |
| Packaging Type | Tube |
| מספר פינים | 8 pins |
תצורת פינים של LM2904ANG
| פין 1 | OUT1 — Amplifier 1 output |
| פין 2 | IN1- — Amplifier 1 inverting input |
| פין 3 | IN1+ — Amplifier 1 non-inverting input |
| פין 4 | V- — Negative supply or ground connection |
| פין 5 | IN2+ — Amplifier 2 non-inverting input |
| פין 6 | IN2- — Amplifier 2 inverting input |
| פין 7 | OUT2 — Amplifier 2 output |
| פין 8 | V+ — Positive supply connection |
יישומים טיפוסיים
LM2904ANG מתאים עבור 6 יישוםs: Industrial Sensor Signal Conditioning, Audio Preamplification, Low-Frequency Active Filtering, Power Supply Current Monitoring, Generic Voltage Amplification, Legacy Equipment Repair.
Industrial Sensor Signal Conditioning
The LM2904ANG can condition low-frequency sensor signals where two channels provide independent amplification or buffering on a controller board. Its dual-amplifier organization, 1 MHz gain-bandwidth product, and 0.6 V/µs slew rate are suitable for common pressure, temperature, and position interfaces operating well below megahertz bandwidth. The common-mode input range extending toward ground or VEE is particularly useful in single-supply sensor circuits whose signals remain close to the lower rail. Engineers should verify the actual input-offset voltage, input-bias current, and allowable source impedance for the selected sensor. Feedback resistors should be placed close to the amplifier, and the circuit must retain sufficient supply headroom for the required output voltage and load.
מומלץ
Audio Preamplification
The LM2904ANG fits low-frequency audio preamplifier stages requiring two signal channels in one 8-PDIP package. Its 1 MHz gain-bandwidth product supports audio-band closed-loop gains when the gain-bandwidth product is not exhausted, while the 0.6 V/µs slew rate provides ample margin for ordinary low-bandwidth audio signals. The common-mode range toward ground or VEE can simplify single-supply headroom planning. Because this is a general-purpose rather than low-noise audio amplifier, system-level noise performance must be evaluated with the chosen resistor values, source impedance, and supply bypass network. Output clipping, load capability, and stability should also be checked before using the device with headphone, line, or mixer stages.
מומלץ
Low-Frequency Active Filtering
The LM2904ANG can implement the two amplifier sections needed for a low-frequency active filter or biquad stage. Its 1 MHz gain-bandwidth product provides more open-loop bandwidth than many applications require, while the 0.6 V/µs slew rate limits large-signal transient behavior for precision filter designs. The device is best suited to signal frequencies well below its bandwidth limit, with component tolerances and noise contributing significantly to the overall response. Grounded single-supply operation requires careful biasing so the signal remains inside the amplifier’s common-mode range. Place feedback components close to the relevant pins, maintain symmetrical ground routing, and test the completed filter across its expected input amplitude and frequency range.
מומלץ
Power Supply Current Monitoring
The LM2904ANG can amplify a scaled voltage representing supply or load current for monitoring and control systems. The dual configuration allows one channel to monitor a power rail while the other handles a related reference or buffered output. The 0.6 V/µs slew rate and 1 MHz gain-bandwidth product are suitable for slow current-loop signals and protection thresholds, and operation from a split supply can simplify measurements around ground. The design must ensure that shunt-amplifier inputs remain within the common-mode range and that the required output does not exceed the output-swing limits. Input filtering, Kelvin routing where applicable, and careful resistor selection help control offset and thermal errors in precision monitoring systems.
מומלץ
Generic Voltage Amplification
The LM2904ANG is suitable for conventional voltage-feedback amplification when the application does not require modern precision or high-speed performance. Two amplifier channels in one 8-PDIP reduce the number of packages required for a basic analog board, while the 1 MHz gain-bandwidth product supports low- to mid-frequency closed-loop gains. The device accepts single or split supplies, allowing integration into legacy industrial and educational circuits. When using it as a non-inverting stage, calculate the closed-loop gain from the feedback divider and verify that the desired output remains within the available swing. When using it as an inverting stage, account for input bias-current effects and select source and feedback resistors that minimize offset error.
מומלץ
Legacy Equipment Repair
The LM2904ANG is useful for repairing or maintaining legacy analog equipment that uses an 8-PDIP dual general-purpose operational amplifier. Its two-circuit configuration and through-hole package make it practical where a board-level replacement is preferable to redesigning the surrounding analog section. The obsolete lifecycle status makes exact footprint, pinout, supply, and temperature verification essential before substitution. Maintenance teams should compare the replacement’s offset voltage, input-bias current, common-mode range, output swing, and stability behavior with the original device. The original board layout should also be inspected for obsolete components and heat-damaged sockets. A replacement should be tested in the complete circuit rather than judged only by its pin arrangement.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור LM2904ANG — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | LM2904NG | LM2904N | LM358N | LM358N | NJM2904D |
|---|---|---|---|---|---|---|
| Brand | onsemi | onsemi | Texas Instruments | STMicroelectronics | Texas Instruments | Renesas Electronics |
| Package | 8-PDIP | 8-PDIP | 8-PDIP | 8-PDIP | 8-PDIP | 8-PDIP |
| Mounting Type | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole |
מבדילים עיקריים
- Two general-purpose amplifier channels in one through-hole package (לעומתLM358N)
- Established LM2904-family application characteristics (לעומתNJM2904D)
- Single- and split-supply compatibility (לעומתLM2904N)
הערות תכנון
Route the two op-amp channels with short feedback paths and keep the inverting-input nodes physically compact to reduce parasitic capacitance and susceptibility to injected noise. Pin 4 is the negative supply or ground connection and pin 8 is the positive supply; provide a low-impedance return path and place bypass capacitors close to the relevant supply pins. The DIP layout should also preserve the manufacturer’s specified notch orientation and pin numbering.
Do not assume that matching the 8-PDIP outline guarantees electrical equivalence. Before substituting a dual amplifier, compare input offset voltage, input-bias current, common-mode range, output swing, output-current capability, supply limits, stability with the selected feedback network, and operating-temperature grade. Single-supply circuits also require verification that the signal and output remain inside the amplifier’s usable input and output ranges.
Check the power-supply range against the exact LM2904ANG ordering-code documentation before energizing the board. The device can operate from a single supply or split supplies, but the positive and negative rails must satisfy the applicable absolute-maximum and operating limits. In battery-powered designs, account for the amplifier’s supply current, output-stage behavior, and the load driven by each channel rather than considering quiescent current alone.
מידע על תאימות
RoHS and REACH are referenced in cross-reference material, but no definitive compliance result was stated. The LM2904ANG is a general-purpose analog IC and is not identified as an AEC-Q100 automotive-qualified device.