Texas Instruments

LM324LVIPWR - Quad 5.5V 1MHz Op Amp | Texas Instruments

N.º de pieza: LM324LVIPWR ✓ Activo
5.5 V Vdss TSSOP (PW) Package
MOQ: 1 |

LM324LVIPWR Descripción general

The Texas Instruments LM324LVIPWR is a quad, general-purpose operational amplifier rated for a 5.5 V maximum supply, operating from ±2.75 V to 5.5 V. Each of its four amplifiers provides 1 MHz of gain-bandwidth product and a 3 mV offset-voltage rating. The device is packaged in a 14-pin TSSOP (PW) and is specified across the -40°C to +125°C industrial temperature range.

An operational amplifier, or op amp, is an analog integrated circuit that amplifies the difference between two input voltages. The LM324LV belongs to the broader hierarchy of operational amplifiers, analog amplifiers, and integrated circuits. Its quad configuration integrates four amplifiers in one package, reducing board area when a design requires several independent gain stages, buffers, comparators, or current-feedback loops.

The LM324LV series is designed for low-voltage operation while retaining the familiar pin arrangement and general-purpose characteristics associated with industry-standard quad amplifiers. The 1 MHz gain-bandwidth product supports audio-frequency and general analog signal conditioning, while the 3 mV offset specification supports precision-enough closed-loop amplification when resistor matching and calibration are considered. The 5.5 V ceiling allows operation from regulated 3.3 V or 5 V rails common in industrial control, instrumentation, sensor-conditioning, and embedded systems.

Because the IC contains four amplifiers, each channel has independent input, output, and power connections arranged according to the manufacturer pin-description table. Typical applications include voltage buffers, transimpedance stages, active filters, differential amplifiers, level shifting, and low-frequency audio paths. Decoupling capacitors near the supply pins help control impedance and prevent supply noise from appearing at the amplifier output.

A key design consideration is that the gain-bandwidth product must be appropriate for the operating frequency. A closed-loop gain of 10 leaves approximately 100 kHz of bandwidth, so higher closed-loop gains reduce usable bandwidth. The offset specification alone does not determine total accuracy; input bias current, input common-mode range, output swing, resistor tolerance, and temperature drift also contribute to the final error budget.

This page organizes the device specifications, package information, design guidance, and engineering selection criteria into a compact reference. It also highlights where additional datasheet details are required before a circuit is released for production.

Alternativas directas para LM324LVIPWR — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con LM324LVIPWR (mismo factor de forma y huella) — difiere en Gain-Bandwidth Product, Supply Voltage Range.

Texas Instruments
Gain-Bandwidth Product: 1.2 MHz
Supply Voltage Range: Up to ±16 V (32 V total)
Comparar con LM324LVIPWR →

LM324PWRE4

✅ Sustitución directa
Texas Instruments
📦 TSSOP-14 (PW)
Quad general-purpose operational amplifier · 4 circuits · 4 independent amplifiers · 1.2 MHz · 1 V/us · Up to ±16 V (32 V total) · Single supply or split supply · Push-pull

Consulte el precio

Ver hoja de datos →

LMV324IPWR

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 TSSOP-14 (PW)
Same 14-pin TSSOP footprint and 1 MHz class; input common-mode and output-swing behavior differ because the LMV324 family is designed around low-voltage rail-to-rail operation.

📋 Alternativa de referencia (no en el catálogo)

LM324LVIPWR Valores máximos y características eléctricas

Number of Amplifiers 4
Amplifier Type General Purpose
Maximum Supply Voltage 5.5 V
Supply Voltage Range ±2.75 V to 5.5 V
Gain-Bandwidth Product 1 MHz
Offset Voltage 3 mV
Rango de temperatura de funcionamiento -40°C to +125°C
Package Type TSSOP (PW)
Número de pines 14
Tipo de montaje Surface Mount
Operating Supply Range ±2.75 V to 5.5 V
Input Offset Voltage 3 mV
Number of Channels 4
Qualification Category Industrial temperature grade, -40°C to +125°C

Guía de configuración de pines de LM324LVIPWR tssop (pw)

Configuración de pines para LM324LVIPWR (encapsulado tssop (pw)). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.

Diagrama de patillaje del encapsulado tssop (pw) para LM324LVIPWR

No hay datos detallados de patillaje disponibles para LM324LVIPWR.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

LM324LVIPWR es adecuado para 6 aplicacións: 3.3 V Sensor Signal Conditioning, Industrial Control Analog Front End, Audio Preamplifier and Mixer, Active Low-Pass Filters, Transimpedance Amplifier, Level Shifting and Difference Amplification.

🏭

3.3 V Sensor Signal Conditioning

The LM324LVIPWR fits low-voltage sensor-conditioning circuits because its ±2.75 V to 5.5 V supply range covers 3.3 V operation, while four amplifiers in one 14-pin TSSOP can implement several conditioning stages. A typical arrangement uses one channel to amplify a sensor signal, another as an active low-pass filter, and a third as a voltage follower for impedance isolation. The 1 MHz gain-bandwidth product provides approximately 100 kHz of closed-loop bandwidth at a noise gain of 10. Designers should verify the input common-mode range and output swing against the sensor's operating region before finalizing the bias points.

🏭

Industrial Control Analog Front End

A 24 V industrial control board can use the LM324LVIPWR after regulation to 3.3 V or 5 V for low-level analog processing. The device's 5.5 V maximum supply rating and industrial temperature range of -40°C to +125°C suit equipment that must operate across temperature variations. Its four channels can support current-to-voltage conversion, differential sensing, gain stages, and output buffering. Because the device is not rail-to-rail by specification, the engineer must confirm that sensor and output common-mode levels remain inside the permitted range and that the selected gain keeps signal distortion within the system budget.

🎧

Audio Preamplifier and Mixer

The LM324LVIPWR can implement low-frequency audio preamplification and summing stages from a 5 V supply. Its 1 MHz gain-bandwidth product is sufficient for many microphone, tone, and intercom paths, while the four-channel configuration allows a two-stage amplifier plus mixing and buffering functions in one package. A practical design should include input and output coupling capacitors, power-supply bypass capacitors, and a feedback network selected for the intended gain and bass response. Verify output swing into the connected load and slew-rate requirements for the highest expected signal frequency before layout approval.

📡

Active Low-Pass Filters

The four channels in the LM324LVIPWR are useful for implementing cascaded active filters in measurement and control systems. A 1 MHz gain-bandwidth product supports low-frequency filter sections, while the 5.5 V supply limit permits operation from 3.3 V or 5 V rails. Two channels can form one second-order active-low-pass section, and the remaining channels can implement another section or provide input and output buffers. Component tolerances, bias-current effects, and amplifier stability must be evaluated together, particularly in very low-gain stages where the bandwidth-to-noise-gain relationship can reduce usable response.

💡

Transimpedance Amplifier

The LM324LVIPWR can serve as the transimpedance amplifier in a photodiode, photocell, or optical sensor interface when the required signal bandwidth is modest. The 1 MHz gain-bandwidth product allows meaningful closed-loop bandwidth at practical feedback values, and the 3 mV offset rating is important when the sensor current is small. The design must account for input bias current, photodiode capacitance, feedback-resistor value, and the added stability network. Place the feedback network close to the amplifier pins and keep the sensitive input node compact to reduce parasitic capacitance and noise pickup.

🔧

Level Shifting and Difference Amplification

The LM324LVIPWR can implement a resistor-based level-shifting or difference stage between a sensor and an analog converter. Four channels allow a complete signal path to be consolidated: input buffering, difference amplification, gain adjustment, and output buffering. Its 3 mV offset rating and 1 MHz bandwidth are appropriate for many low-speed measurements, but the final accuracy also depends on matched resistor networks, bias current, common-mode range, and output capability. For a bridge or differential sensor, select resistor networks with suitable tolerance and temperature behavior, and verify that the inputs remain within the amplifier's permitted common-mode interval.

What is the operating voltage of the LM324LVIPWR?
The LM324LVIPWR operates from ±2.75 V to 5.5 V. According to the Texas Instruments LM324LV product page, the device is a quad operational amplifier with a 5.5 V maximum supply rating, making it suitable for 3.3 V and 5 V systems. The operating range also permits bipolar-style ±2.5 V supplies when the negative rail is properly generated. Use the manufacturer datasheet for the complete electrical characteristic table and recommended operating conditions.
What are the key specifications of LM324LVIPWR that engineers should know?
The LM324LVIPWR is a four-channel, general-purpose operational amplifier with a 5.5 V maximum supply, 1 MHz gain-bandwidth product, 3 mV offset voltage, and a -40°C to +125°C temperature range. Texas Instruments identifies the device in a 14-pin TSSOP (PW) package. The quad configuration consolidates four amplifiers into one footprint, while the low-voltage rating supports 3.3 V and 5 V industrial designs.
Where can I download the LM324LVIPWR datasheet PDF?
The official LM324LVIPWR documentation is available through the Texas Instruments LM324LV product page at https://www.ti.com/product/LM324LV. The manufacturer page links the device data sheet, part-order details, and family information. Use the pin-description table, electrical characteristics, and recommended operating conditions in the manufacturer data sheet when assigning PCB nets and verifying circuit limits.
Where can I find the LM324LVIPWR pinout?
The LM324LVIPWR pinout is defined in the Texas Instruments LM324LV manufacturer data sheet and product-page package information. The device uses a 14-pin TSSOP (PW) package with four operational amplifiers. Use the pin-description table in the manufacturer data sheet when assigning the four amplifier channels, supply rails, and ground connections, and follow the package drawing for the physical land pattern.
Is LM324LVIPWR pin compatible with LM324LVIDR?
No. LM324LVIPWR is in a 14-pin TSSOP (PW) package, while LM324LVIDR is identified in the comparison material as a 14-pin SOIC device. Their amplifier functions are related, but the physical footprints are different, so LM324LVIDR is not a board-level drop-in replacement for LM324LVIPWR without changing the PCB layout. Use the manufacturer package drawings to confirm mechanical differences.
Can LM324LVIPWR replace a standard LM324 in a 5 V circuit?
The LM324LVIPWR can suit a 5 V circuit when its input, output, and common-mode limits remain inside the device specifications, but it is not a universal mechanical substitute for every LM324 package variant. Its 5.5 V maximum supply and 1 MHz gain-bandwidth product differ from the full-voltage range of the classic LM324. Check the footprint, supply rating, common-mode range, output swing, and stability requirements before substituting it.
What can replace the LM324LVIPWR?
A true drop-in replacement must use the same 14-pin TSSOP footprint, match the amplifier pin arrangement, and stay close to the LM324LVIPWR's 5.5 V supply, 1 MHz bandwidth, and 3 mV offset ratings. The LM324LVIPWR is the identified 14-pin TSSOP member of the TI LM324LV family in the available records. For a different package or different electrical ratings, treat the candidate as a functional alternative and verify its pinout and datasheet.
When should I choose LM324LVIPWR over a wider-supply quad op amp?
Choose LM324LVIPWR when the design runs from ±2.75 V to 5.5 V and requires a conventional general-purpose amplifier rather than rail-to-rail input or output operation. Its 1 MHz bandwidth and 3 mV offset rating suit low-frequency signal-conditioning paths. A wider-supply amplifier may be preferable when the circuit operates below 2.7 V, requires rail-to-rail swing, or needs substantially higher bandwidth.
Is LM324LVIPWR suitable for 3.3 V sensor conditioning?
Yes, LM324LVIPWR is suitable for 3.3 V sensor-conditioning circuits when the signal and output remain within the amplifier's common-mode and output-swing limits. The device supports a ±2.75 V to 5.5 V supply range, provides four channels in one 14-pin TSSOP package, and offers 1 MHz of gain-bandwidth product. Biasing near either supply rail may require a rail-to-rail input amplifier instead.
LM324LVIPWR vs LM324LVIDR: which package should I choose?
Choose LM324LVIPWR for a 14-pin TSSOP (PW) layout and LM324LVIDR for a 14-pin SOIC layout. Both belong to the low-voltage LM324LV product family, but their physical packages differ. The TSSOP offers a smaller footprint, while the SOIC package provides wider lead spacing that can simplify hand assembly and inspection. Neither choice changes the device's 5.5 V maximum supply rating.
What is the best drop-in replacement for LM324LVIPWR?
The best drop-in replacement is the candidate with an identical 14-pin TSSOP land pattern, the same channel-by-channel pin assignment, and comparable 5.5 V supply, 1 MHz bandwidth, and offset performance. The identified LM324LV family records do not establish another TSSOP part as a confirmed drop-in equivalent. Treat any proposed substitute as a design-review item and verify its pinout, package drawing, electrical limits, and stability behavior.
How much bandwidth is available at a closed-loop gain of 10?
The LM324LVIPWR has a 1 MHz gain-bandwidth product, so the approximate closed-loop bandwidth at a noise gain of 10 is 100 kHz. The rule is bandwidth in megahertz divided by the noise gain. Actual usable signal bandwidth also depends on slew rate, load, output swing, and frequency response, which should be checked in the manufacturer data sheet when the signal contains significant low-frequency content.
Does the LM324LVIPWR include four independent amplifiers?
Yes, the LM324LVIPWR contains four operational amplifiers in one 14-pin TSSOP package. Texas Instruments describes it as a quad amplifier, and the manufacturer pin-description table identifies the input, output, supply, and ground connections for each channel. The channels share package power pins but otherwise support separate signal paths, such as one buffer per sensor or one active-filter section per amplifier.
Where can I buy LM324LVIPWR online?
Use the Request a Quote form on this page to request current LM324LVIPWR availability, order quantities, and delivery information. The listing is offered in a 14-pin TSSOP (PW) package with a -40°C to +125°C temperature range. For prototype builds, confirm the package suffix and tape-and-reel requirements when submitting the request.
What is the price of LM324LVIPWR?
Request a current quotation for LM324LVIPWR through the Request a Quote form on this page. Commercial terms can change with quantity, inventory position, and packaging requirements, so a current quote is the appropriate purchasing path. Include the target quantity, 14-pin TSSOP (PW) package, and any required traceability information when submitting the request.
What is the lead time for LM324LVIPWR?
Request the current lead time for LM324LVIPWR through the Request a Quote form on this page. Lead time depends on the ordered quantity, package format, and current supply conditions. The device is specified in a 14-pin TSSOP (PW) package for surface-mount assembly, so confirm whether tape-and-reel presentation is required before placing the order.
Is LM324LVIPWR currently in stock?
Current inventory for LM324LVIPWR is confirmed through the Request a Quote form on this page. The Request a Quote workflow provides the appropriate stock and delivery response for the requested quantity. Specify the required quantity and packaging format, and request traceability documentation if the application requires it.

Datos de referencia de ingeniería para LM324LVIPWR — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose LM324LVIPWR when the design requires four general-purpose amplifiers, a 3.3 V or 5 V rail, and a 14-pin TSSOP footprint. It is well suited to low-frequency sensor conditioning, buffering, active filtering, audio preamplification, and general industrial control. Confirm that the input common-mode range and output swing fit the circuit, and check whether the 1 MHz gain-bandwidth product is sufficient at the intended closed-loop gain. LM324LVIDR is useful when a 14-pin SOIC footprint is preferred, but it is not a board-level substitute because the packages differ. For designs requiring rail-to-rail operation, operation below 2.7 V, or substantially higher bandwidth, evaluate a different quad amplifier family rather than assuming standard LM324 behavior.

Comparación con alternativas

Parámetro Este producto
Package 14-pin TSSOP (PW)
Brand Texas Instruments
Number of Amplifiers 4
Maximum Supply Voltage 5.5 V
Supply Voltage Range ±2.75 V to 5.5 V
Gain-Bandwidth Product 1 MHz
Offset Voltage 3 mV
Operating Temperature Range -40°C to +125°C

Diferenciadores clave

  • Four independent amplifiers in a compact 14-pin TSSOP (frente a LM324LVIDR)
  • Low-voltage operation matched to embedded analog rails (frente a Standard full-range LM324 implementations)
  • General-purpose performance for low-frequency conditioning (frente a High-speed precision quad amplifiers)

Notas de diseño

Place the power-supply bypass capacitor close to the device supply pins and connect the ground return directly to the package ground pins. Keep sensitive input and feedback traces short, and avoid routing them beneath digital switching nodes. A compact ground plane helps return currents reach the amplifier without crossing high-current paths. Follow the manufacturer land pattern for the 14-pin TSSOP (PW) footprint and confirm pin 1 orientation against the package drawing before fabrication.

Calculate closed-loop bandwidth as approximately 1 MHz divided by the noise gain rather than treating 1 MHz as the usable signal bandwidth at every configuration. A gain of 10 leaves roughly 100 kHz of bandwidth, while a gain of 100 leaves about 10 kHz. Check the resulting bandwidth against the signal's harmonics and settling requirements, and use the manufacturer data sheet to confirm stability with the selected feedback network and capacitive load.

Do not assume rail-to-rail input or output behavior. Check the operating common-mode range, output swing, and supply limits for the exact circuit state, including startup and output saturation. The 3 mV offset rating is only one contributor to error; resistor tolerance, bias current, noise, and temperature drift may dominate. For signals centered near a supply rail, choose an amplifier whose input and output operating ranges are explicitly suitable.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The device is specified for industrial temperatures from -40°C to +125°C. RoHS, REACH, halogen-free, lead-free, conflict-minerals, and AEC-Q100 status require confirmation from the current manufacturer product documentation.

Búsquedas relacionadas

LM324LVIPWR datasheet LM324LVIPWR pinout LM324LVIPWR datasheet pdf LM324LVIPWR equivalent LM324LVIPWR drop-in replacement LM324LVIPWR vs LM324LVIDR LM324LVIPWR 14 pin TSSOP LM324LVIPWR footprint LM324LVIPWR 5.5V op amp LM324LVIPWR 3.3V application circuit LM324LVIPWR price LM324LVIPWR stock Texas Instruments LM324LVIPWR LM324LVIPWR cross reference

Componentes & términos relacionados

Texas Instruments LM324LVIPWR LM324LV LM324LVIDR LM324LVPWR operational amplifier quad amplifier general-purpose amplifier analog amplifier integrated circuit semiconductor low-dropout voltage regulator
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ