LM324LVIPWR - Quad 5.5V 1MHz Op Amp | Texas Instruments
部品番号: LM324LVIPWR ✓ 生産中LM324LVIPWR 概要
An operational amplifier, or op amp, is an analog integrated circuit that amplifies the difference between two input voltages. The LM324LV belongs to the broader hierarchy of operational amplifiers, analog amplifiers, and integrated circuits. Its quad configuration integrates four amplifiers in one package, reducing board area when a design requires several independent gain stages, buffers, comparators, or current-feedback loops.
The LM324LV series is designed for low-voltage operation while retaining the familiar pin arrangement and general-purpose characteristics associated with industry-standard quad amplifiers. The 1 MHz gain-bandwidth product supports audio-frequency and general analog signal conditioning, while the 3 mV offset specification supports precision-enough closed-loop amplification when resistor matching and calibration are considered. The 5.5 V ceiling allows operation from regulated 3.3 V or 5 V rails common in industrial control, instrumentation, sensor-conditioning, and embedded systems.
Because the IC contains four amplifiers, each channel has independent input, output, and power connections arranged according to the manufacturer pin-description table. Typical applications include voltage buffers, transimpedance stages, active filters, differential amplifiers, level shifting, and low-frequency audio paths. Decoupling capacitors near the supply pins help control impedance and prevent supply noise from appearing at the amplifier output.
A key design consideration is that the gain-bandwidth product must be appropriate for the operating frequency. A closed-loop gain of 10 leaves approximately 100 kHz of bandwidth, so higher closed-loop gains reduce usable bandwidth. The offset specification alone does not determine total accuracy; input bias current, input common-mode range, output swing, resistor tolerance, and temperature drift also contribute to the final error budget.
This page organizes the device specifications, package information, design guidance, and engineering selection criteria into a compact reference. It also highlights where additional datasheet details are required before a circuit is released for production.
ドロップイン代替品: LM324LVIPWR — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: LM324LVIPWR (同一形状・フットプリント) — 相違点: Gain-Bandwidth Product, Supply Voltage Range.
LM324PWRE4
✅ ドロップイン価格はお問い合わせください
データシートを見る →LMV324IPWR
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
LM324LVIPWR 最大定格&電気的特性
| Number of Amplifiers | 4 |
| Amplifier Type | General Purpose |
| Maximum Supply Voltage | 5.5 V |
| Supply Voltage Range | ±2.75 V to 5.5 V |
| Gain-Bandwidth Product | 1 MHz |
| Offset Voltage | 3 mV |
| 動作温度範囲 | -40°C to +125°C |
| Package Type | TSSOP (PW) |
| ピン数 | 14 |
| 実装タイプ | Surface Mount |
| Operating Supply Range | ±2.75 V to 5.5 V |
| Input Offset Voltage | 3 mV |
| Number of Channels | 4 |
| Qualification Category | Industrial temperature grade, -40°C to +125°C |
LM324LVIPWR tssop (pw) ピン配置ガイド
LM324LVIPWR (tssop (pw) パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: LM324LVIPWR.
詳細は データシート をご参照ください。
主な用途
LM324LVIPWR の用途: 6 件s: 3.3 V Sensor Signal Conditioning, Industrial Control Analog Front End, Audio Preamplifier and Mixer, Active Low-Pass Filters, Transimpedance Amplifier, Level Shifting and Difference Amplification.
3.3 V Sensor Signal Conditioning
The LM324LVIPWR fits low-voltage sensor-conditioning circuits because its ±2.75 V to 5.5 V supply range covers 3.3 V operation, while four amplifiers in one 14-pin TSSOP can implement several conditioning stages. A typical arrangement uses one channel to amplify a sensor signal, another as an active low-pass filter, and a third as a voltage follower for impedance isolation. The 1 MHz gain-bandwidth product provides approximately 100 kHz of closed-loop bandwidth at a noise gain of 10. Designers should verify the input common-mode range and output swing against the sensor's operating region before finalizing the bias points.
おすすめ
Industrial Control Analog Front End
A 24 V industrial control board can use the LM324LVIPWR after regulation to 3.3 V or 5 V for low-level analog processing. The device's 5.5 V maximum supply rating and industrial temperature range of -40°C to +125°C suit equipment that must operate across temperature variations. Its four channels can support current-to-voltage conversion, differential sensing, gain stages, and output buffering. Because the device is not rail-to-rail by specification, the engineer must confirm that sensor and output common-mode levels remain inside the permitted range and that the selected gain keeps signal distortion within the system budget.
おすすめ
Audio Preamplifier and Mixer
The LM324LVIPWR can implement low-frequency audio preamplification and summing stages from a 5 V supply. Its 1 MHz gain-bandwidth product is sufficient for many microphone, tone, and intercom paths, while the four-channel configuration allows a two-stage amplifier plus mixing and buffering functions in one package. A practical design should include input and output coupling capacitors, power-supply bypass capacitors, and a feedback network selected for the intended gain and bass response. Verify output swing into the connected load and slew-rate requirements for the highest expected signal frequency before layout approval.
おすすめ
Active Low-Pass Filters
The four channels in the LM324LVIPWR are useful for implementing cascaded active filters in measurement and control systems. A 1 MHz gain-bandwidth product supports low-frequency filter sections, while the 5.5 V supply limit permits operation from 3.3 V or 5 V rails. Two channels can form one second-order active-low-pass section, and the remaining channels can implement another section or provide input and output buffers. Component tolerances, bias-current effects, and amplifier stability must be evaluated together, particularly in very low-gain stages where the bandwidth-to-noise-gain relationship can reduce usable response.
おすすめ
Transimpedance Amplifier
The LM324LVIPWR can serve as the transimpedance amplifier in a photodiode, photocell, or optical sensor interface when the required signal bandwidth is modest. The 1 MHz gain-bandwidth product allows meaningful closed-loop bandwidth at practical feedback values, and the 3 mV offset rating is important when the sensor current is small. The design must account for input bias current, photodiode capacitance, feedback-resistor value, and the added stability network. Place the feedback network close to the amplifier pins and keep the sensitive input node compact to reduce parasitic capacitance and noise pickup.
おすすめ
Level Shifting and Difference Amplification
The LM324LVIPWR can implement a resistor-based level-shifting or difference stage between a sensor and an analog converter. Four channels allow a complete signal path to be consolidated: input buffering, difference amplification, gain adjustment, and output buffering. Its 3 mV offset rating and 1 MHz bandwidth are appropriate for many low-speed measurements, but the final accuracy also depends on matched resistor networks, bias current, common-mode range, and output capability. For a bridge or differential sensor, select resistor networks with suitable tolerance and temperature behavior, and verify that the inputs remain within the amplifier's permitted common-mode interval.
おすすめ
エンジニアリング参考データ: LM324LVIPWR — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 |
|---|---|
| Package | 14-pin TSSOP (PW) |
| Brand | Texas Instruments |
| Number of Amplifiers | 4 |
| Maximum Supply Voltage | 5.5 V |
| Supply Voltage Range | ±2.75 V to 5.5 V |
| Gain-Bandwidth Product | 1 MHz |
| Offset Voltage | 3 mV |
| Operating Temperature Range | -40°C to +125°C |
主な差別化要因
- Four independent amplifiers in a compact 14-pin TSSOP (vs LM324LVIDR)
- Low-voltage operation matched to embedded analog rails (vs Standard full-range LM324 implementations)
- General-purpose performance for low-frequency conditioning (vs High-speed precision quad amplifiers)
設計ノート
Place the power-supply bypass capacitor close to the device supply pins and connect the ground return directly to the package ground pins. Keep sensitive input and feedback traces short, and avoid routing them beneath digital switching nodes. A compact ground plane helps return currents reach the amplifier without crossing high-current paths. Follow the manufacturer land pattern for the 14-pin TSSOP (PW) footprint and confirm pin 1 orientation against the package drawing before fabrication.
Calculate closed-loop bandwidth as approximately 1 MHz divided by the noise gain rather than treating 1 MHz as the usable signal bandwidth at every configuration. A gain of 10 leaves roughly 100 kHz of bandwidth, while a gain of 100 leaves about 10 kHz. Check the resulting bandwidth against the signal's harmonics and settling requirements, and use the manufacturer data sheet to confirm stability with the selected feedback network and capacitive load.
Do not assume rail-to-rail input or output behavior. Check the operating common-mode range, output swing, and supply limits for the exact circuit state, including startup and output saturation. The 3 mV offset rating is only one contributor to error; resistor tolerance, bias current, noise, and temperature drift may dominate. For signals centered near a supply rail, choose an amplifier whose input and output operating ranges are explicitly suitable.
コンプライアンス情報
The device is specified for industrial temperatures from -40°C to +125°C. RoHS, REACH, halogen-free, lead-free, conflict-minerals, and AEC-Q100 status require confirmation from the current manufacturer product documentation.