LM339M - Quad Open-Collector Comparator | Texas Instruments
N.º de pieza: LM339M ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $0 | $0,00 |
| 10 | $0 | $0,00 |
| 100 | $0 | $0,00 |
| 500 | $0 | $0,00 |
| 1.000 | $0 | $0,00 |
LM339M Descripción general
A comparator is an analog integrated circuit that compares two input voltages and produces a digital logic state indicating which input is higher. The LM339 belongs to the broader hierarchy of analog comparator ICs, voltage-detection devices, and general-purpose signal-conditioning components. Its four independent channels allow one package to implement multiple threshold, overvoltage, undervoltage, window, or sorting decisions while sharing a common supply architecture.
Key features include four open-collector outputs, low supply current, low input bias current, low-offset operation, and an input common-mode range that includes ground on single-supply systems. Open-collector outputs require an external pull-up resistor and can support wired logic, connector interfaces, level translation, or multiple devices sharing a bus when the electrical conditions are appropriate. Unlike a push-pull output, this architecture provides useful flexibility at the cost of requiring an external pull-up and having a slower rising edge.
The LM339M can operate from 2 V to 36 V, while the verified distributor listing identifies SOIC-14 packaging and a 0 °C to 70 °C temperature grade for the listed Texas Instruments LM339M variant. The four comparators share supply pins but have independent noninverting and inverting inputs. Pin assignment and input polarity must be verified against the manufacturer datasheet before layout, especially because the M suffix identifies the package configuration rather than a different comparator function.
Typical applications include DC overvoltage and undervoltage detection, battery threshold monitoring, industrial control interfaces, sensor conditioning, open-collector alarm signaling, and four-channel comparator banks in embedded systems. A pull-up resistor on each output is normally required. Inputs must remain within the device’s common-mode limits, and supply bypass should follow the manufacturer’s recommended layout practice to reduce susceptibility to switching noise and lead instability.
This page consolidates the verified LM339M specifications, source links, packaging information, and application-oriented design guidance. It deliberately separates confirmed values from unspecified electrical details; parameters not present in the supplied data are not inferred here.
Alternativas directas para LM339M — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
LM339M/NOPB
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
LM339DG
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
LM339M
✅ Sustitución directa✓ En stock
Consulte el precio
Ver hoja de datos →LM339M/NOPB
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
LM339M
✅ Sustitución directa✓ En stock
Consulte el precio
Ver hoja de datos →LM339M Valores máximos y características eléctricas
| Comparator Type | Quad differential voltage comparator |
| Number of Comparators | 4 independent comparators |
| Supply Voltage Range | 2 V to 36 V |
| Rango de tensión de entrada | ±1 V to ±18 V |
| Response Time | 1.3 µs |
| Supply Current Drain | 800 µA typical |
| Input Bias Current | 25 nA typical |
| Tipo de salida | Open-collector |
| Encapsulado | 14-pin SOIC |
| Temperatura de funcionamiento | 0 °C to +70 °C |
| Tipo de montaje | Surface mount |
| Número de pines | 14 pins |
| Application Category | Standard general-purpose comparator |
| Logic Compatibility | Open-collector external pull-up interface |
| Manufacturer | Texas Instruments |
| Datasheet Description | Low-power low-offset voltage quad comparators |
| Input Common-Mode Range | Includes ground in single-supply operation |
| Drop-in Replacement Status | Use only verified pin-compatible alternatives |
Guía de configuración de pines de LM339M 14-pin soic
Configuración de pines para LM339M (encapsulado 14-pin soic). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para LM339M.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
LM339M es adecuado para 6 aplicacións: Battery Undervoltage Detection, DC Overvoltage Protection, Industrial Sensor Interfacing, Open-Collector Alarm Interface, Power-Good Sequencing, Wired-Logic Level Translation.
Battery Undervoltage Detection
The LM339M fits battery undervoltage detection because its four independent channels can monitor multiple thresholds while the verified supply range is 2 V to 36 V. Connect resistor dividers to the noninverting and inverting inputs, then use each open-collector output to signal a regulator, load switch, or controller. A pull-up resistor establishes the logic-high state. Design the divider around the battery’s maximum cell voltage and account for input bias current, offset, and threshold tolerances before setting the trip points.
Recomendado
DC Overvoltage Protection
LM339M can provide an independent hardware overvoltage decision in a power-conversion or battery system. Its open-collector outputs can be wired to an inhibit, crowbar, relay driver, or digital controller input when the target voltage and sink-current requirements are verified. The 2 V to 36 V supply specification allows use across many DC rails, but the input divider, clamp strategy, response time of 1.3 µs, and fault-safe pull-up arrangement must be validated for the actual fault condition.
Recomendado
Industrial Sensor Interfacing
The LM339M is appropriate for low-power industrial sensor thresholding where a sensor produces an analog signal that must be converted into a control decision. Its typical 25 nA input bias current helps reduce loading of high-impedance sensor networks, while four channels provide independent comparisons in one package. The open-collector outputs can be pulled up to the logic rail used by a controller. Protect long sensor wiring against ESD and noise, and verify the input common-mode range for every operating rail.
Recomendado
Open-Collector Alarm Interface
LM339M suits alarm and fault-signaling circuits because its open-collector outputs can be connected to pull-up resistors or shared collector lines. A comparator channel can monitor a fault condition, while another channel can monitor power-good, overtemperature, or communication-line status. The pull-up voltage determines the interface level, and the output current limit must be checked against the number of wired devices. Use fail-safe logic so that a disconnected wire or power loss produces the intended alarm state.
Recomendado
Power-Good Sequencing
LM339M can monitor multiple power rails and generate discrete power-good signals using its four independent comparator channels. Each channel compares a divided rail voltage against a reference or another divided rail, and the open-collector output can feed an enable, reset, or status input through a pull-up. The 2 V to 36 V operating range is useful for monitoring varied DC rails, but sequencing delays, input offset, resistor tolerance, and the target controller’s enable thresholds require calculation and bench verification.
Recomendado
Wired-Logic Level Translation
LM339M can participate in simple open-collector level translation when one side uses a lower pull-up voltage and the other side uses a higher pull-up or receiving device. The open-collector structure is particularly useful for wired-AND or fault-tolerant logic because the output can sink current without actively driving a high level. Confirm voltage tolerances, leakage current, pull-up current, and logic timing at each connected node. The 1.3 µs listed response time should be checked against the required bus rise-time budget.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para LM339M — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | LM339M/NOPB | LM339DG | LM339M | LM339M |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | onsemi | onsemi | Texas Instruments |
| Package | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC |
| Comparator Count | 4 | 4 | 4 | 4 | 4 |
Diferenciadores clave
- Four independent comparator channels in one 14-pin SOIC package (frente a LM339DG)
- Open-collector interface architecture (frente a LM339M/NOPB)
- Low-power operation and low input bias (frente a LM339M)
Notas de diseño
Do not treat LM339M as a push-pull logic device. Every open-collector output needs a pull-up resistor when a stable high level is required. Select the pull-up voltage for the receiving logic, and calculate its current using the target low-state sink requirement. The supplied data confirms the open-collector architecture but does not provide the full output-current table, so consult the manufacturer datasheet before wiring multiple alert lines or an external connector.
Place input traces and output pull-up networks close to the 14-pin SOIC, keeping the analog comparison nodes away from switching-current paths and high-impedance sensor inputs. Use a common ground reference for the comparator and threshold network, and place supply bypass capacitance at the package supply pins according to the manufacturer layout guidance. Long traces increase susceptibility to noise and can make the 1.3 µs listed response time less representative of the complete circuit.
The LM339M can operate from 2 V to 36 V, but the external pull-up, input dividers, and connected logic must also be rated for the intended voltage. Do not use the supply range as permission to exceed the absolute maximum ratings. In dual-supply systems, verify input polarity and common-mode limits against the complete datasheet; the listed ±1 V to ±18 V input range should not be treated as permission for arbitrary negative signals.
Información de cumplimiento
The supplied verified data does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. The LM339M is an analog comparator rather than an automotive-qualified device in the provided data.
