LT1112IS8 - 750kHz Dual Precision Op Amp | Analog Devices
N.º de pieza: LT1112IS8 ✓ ActivoLT1112IS8 Descripción general
An operational amplifier is a high-gain differential amplifier used to amplify a difference between two input voltages. Its common categories include precision amplifiers, transimpedance amplifiers, instrumentation amplifiers, and general-purpose amplifiers. Within the analog semiconductor hierarchy, the LT1112IS8 belongs to the operational-amplifier and signal-conditioning family. Its dual configuration provides two amplifiers in one package, reducing board area while preserving independent input, output, and supply connections for each channel.
The LT1112 family emphasizes low cost, low power, precision, and picoamp input characteristics. The LT1112IS8 provides a 750 kHz gain-bandwidth product and a 0.3 V/µs slew rate, making it appropriate for low-frequency measurement and signal-conditioning paths rather than high-speed communications. Maximum input offset voltage is 160 µV, while the associated product data identifies the part as a general-purpose amplifier in an 8-SO package. An industrial temperature option is represented by the IS8 ordering code.
The amplifier's precision-oriented design supports accurate closed-loop gain and low-level input conditioning. Picoamp input behavior is particularly valuable when the source is a high-impedance sensor, photodiode, or leakage-sensitive analog node. The dual architecture allows adjacent circuit sections to share a supply package, including independent instrumentation channels, buffer stages, active filters, or low-level sensor front ends. The 8-pin SOIC outline is also convenient for conventional surface-mount assembly.
Typical uses include precision current-to-voltage conversion, low-level sensor amplification, laboratory instrumentation, audio and measurement signal paths, bridge-amplifier interfaces, and general dual-channel analog conditioning. Selection should account for the 750 kHz bandwidth and 0.3 V/µs slew rate when setting closed-loop gain or operating against large capacitive loads. High-gain, high-frequency designs require additional stability analysis rather than treating the amplifier as a general high-speed comparator or rail-to-rail device.
For practical layout, keep input and feedback traces short, place decoupling capacitors near the supply pins, and route high-impedance input nodes away from switching nodes. Input bias-current compensation should use the manufacturer's recommended resistor values when source impedances are comparable. Avoid excessive resistive loading and long PCB leakage paths because those factors can undermine the benefit of picoamp input behavior.
This product page consolidates the key electrical characteristics, package details, replacement guidance, application guidance, and design considerations needed to evaluate the LT1112IS8. It also distinguishes the device from higher-bandwidth precision op amps and provides practical guidance for stable PCB implementation, source impedance selection, and drop-in replacement assessment.
Alternativas directas para LT1112IS8 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con LT1112IS8 (mismo factor de forma y huella) — difiere en Amplifier Type, Slew Rate, Gain-Bandwidth Product, Number of Circuits, Operating Temperature.
LT1112S8
✅ Sustitución directaConsulte el precio
Ver hoja de datos →LT1112CS8
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
OPA2134UA/2K5
✅ Sustitución directaConsulte el precio
Ver hoja de datos →LM4562
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
AD8620ARZ
✅ Sustitución directaConsulte el precio
Ver hoja de datos →LT1112IS8 Valores máximos y características eléctricas
| Amplifier Type | General-purpose precision operational amplifier |
| Number of Circuits | 2 circuits |
| Number of Amplifiers | 2 amplifiers |
| Gain-Bandwidth Product | 750 kHz |
| Slew Rate | 0.3 V/µs |
| Maximum Input Offset Voltage | 160 µV |
| Input Bias Current Class | Picoamp input |
| Power Class | Low power |
| Package Type | 8-SOIC, 0.154 inch, 3.90 mm width |
| Tipo de montaje | Surface mount |
| Número de pines | 8 pins |
| Estado RoHS | unknown |
| REACH Status | unknown |
Configuración de pines de LT1112IS8
| Pin 1 | OUTA — Amplifier A output |
| Pin 2 | -INA — Inverting input for amplifier A |
| Pin 3 | +INA — Noninverting input for amplifier A |
| Pin 4 | V- — Negative supply connection |
| Pin 5 | +INB — Noninverting input for amplifier B |
| Pin 6 | -INB — Inverting input for amplifier B |
| Pin 7 | OUTB — Amplifier B output |
| Pin 8 | V+ — Positive supply connection |
Aplicaciones típicas
LT1112IS8 es adecuado para 6 aplicacións: Precision Current-to-Voltage Conversion, High-Impedance Sensor Conditioning, Laboratory Instrumentation, Bridge Sensor Amplification, Active Filtering and Signal Conditioning, Audio and Low-Level Analog Paths.
Precision Current-to-Voltage Conversion
The LT1112IS8 fits a transimpedance front end where a low-level sensor current must be converted into a measurable voltage. Its picoamp-input positioning is useful with high source impedances, while the 160 µV maximum offset limits input-referred error after the required transimpedance gain is applied. The amplifier is used with a feedback resistor and optional compensation capacitor selected from the manufacturer’s application guidance. The main performance check is bandwidth: the 750 kHz gain-bandwidth product must exceed the closed-loop bandwidth created by the feedback network. The 0.3 V/µs slew rate also limits large-signal response, so the design should avoid treating this precision device as a high-speed transimpedance amplifier.
Recomendado
High-Impedance Sensor Conditioning
The LT1112IS8 can condition outputs from high-impedance sensors where input bias current and offset error are more important than high bandwidth. Picoamp input behavior helps preserve sensor integrity, while the 160 µV maximum input offset voltage supports stable measurement of small differential signals. Place the amplifier close to the sensor or connector, shorten the input conductors, and protect the board from contamination when leakage paths could rival the device’s input-current characteristics. Source impedances should also be balanced where practical, with bias-current compensation applied according to the datasheet. The 750 kHz bandwidth is adequate for many environmental and laboratory sensors but not for high-bandwidth piezoelectric or optical signals without additional stages.
Recomendado
Laboratory Instrumentation
The LT1112IS8 is suitable for buffering and gain stages in precision laboratory instruments where dual-channel economy helps reduce PCB area. The two independent channels can handle related measurement inputs, reference buffering, or amplifier outputs within one 8-pin SOIC package. Its 750 kHz gain-bandwidth product supports low-frequency measurement paths, and picoamp input behavior is advantageous when source impedances are high. However, the 0.3 V/µs slew rate means large output excursions settle relatively slowly, making the device better for DC and low-frequency accuracy than for wideband laboratory signals. Designers should include output loading, capacitor compensation, and grounding considerations in the amplifier stability analysis.
Recomendado
Bridge Sensor Amplification
The LT1112IS8 can provide differential gain and buffering for resistive bridge sensors in which the useful signal is small relative to common-mode voltage. The 160 µV maximum offset helps reduce input-referred measurement error, while the dual channel allows paired amplification or differential-to-single-ended signal processing when the selected configuration supports that use. The 750 kHz bandwidth is suitable for many temperature, pressure, and force measurements with modest bandwidth requirements. Critical design checks include bridge excitation noise, input common-mode range, source-impedance balance, and input-bias-current effects. Because the LT1112 is not specified as rail-to-rail, the bridge excitation and output levels must remain within the manufacturer’s guaranteed operating region.
Recomendado
Active Filtering and Signal Conditioning
The LT1112IS8 is appropriate for low-frequency active filters and general signal-conditioning blocks where precision offset and low input current are important. Two amplifiers in one package can implement cascaded stages, buffered filters, or coordinated gain paths while sharing supply pins. The 750 kHz gain-bandwidth product determines the upper practical operating range for each closed-loop gain, and the 0.3 V/µs slew rate constrains large-signal behavior. Filter-component tolerances and op-amp gain error should therefore be evaluated together rather than treating the nominal bandwidth as the complete stability criterion. Keep feedback loops compact, verify capacitive-load stability using the manufacturer's guidance, and bypass the supply pins locally to prevent coupled noise from degrading the measured signal.
Recomendado
Audio and Low-Level Analog Paths
The LT1112IS8 can serve in low-level audio and analog conditioning paths when the design prioritizes low offset, picoamp input behavior, and low power over wide bandwidth. The dual channel may be used for independent signal stages or as a stereo pair in line-level circuitry. Its 0.3 V/µs slew rate is conservative for high-fidelity audio applications, but it remains suitable for many tone and control-signal paths operating at lower frequencies. The 160 µV maximum offset is small relative to common audio signal levels, while picoamp input behavior can help when the source is high impedance. The design should still account for output swing, noise performance, channel-to-channel matching, and the load presented by the following audio stage.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para LT1112IS8 — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | LT1112S8 | LT1112CS8 | OPA2134 | LM4562 | AD8620 |
|---|---|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Texas Instruments | Texas Instruments | Analog Devices |
| Number of Amplifiers | 2 | 2 | 2 | 2 | 2 | 2 |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
Diferenciadores clave
- Combines two picoamp-input precision channels in one 8-SOIC package (frente a LT1112S8)
- Matches the same-family bandwidth and slew-rate performance (frente a LT1112CS8)
- Lower maximum input offset than LM4562 comparison class (frente a LM4562)
- Established dual SOIC footprint with standard pin configuration (frente a AD8620)
Notas de diseño
Route the noninverting and inverting inputs as short, guarded traces, especially when the LT1112IS8 drives a high-impedance source. Keep feedback components close to their associated pins, avoid routing beneath noisy switching nodes, and use a continuous ground reference rather than a fragmented signal-ground plane. Picoamp input behavior can preserve sensor accuracy, but contaminated board leakage and long exposed connections may still create errors comparable to the measured signal.
Do not select the LT1112IS8 solely by its offset-voltage rating. Confirm supply voltage, input common-mode range, output swing, load current, operating temperature, and stability with the intended feedback network. The 750 kHz gain-bandwidth product and 0.3 V/µs slew rate make the device most appropriate for low-frequency precision paths. Applying a higher closed-loop gain or driving a large capacitive load without stability analysis can produce errors that offset-voltage specifications alone will not reveal.
Place the supply-bypass capacitor directly between each supply pin and the corresponding ground reference, with the shortest possible ground return. Keep sensitive input and feedback nodes away from the capacitor and regulator-current paths. If bias-current compensation is required, use the resistor values specified by the manufacturer and ensure the two input source impedances remain reasonably matched, since unmatched impedances convert input-current error into an offset-like measurement error.
Evaluate settling time from both bandwidth and slew-rate limits rather than relying on the 750 kHz gain-bandwidth product alone. For a required closed-loop bandwidth, the available amplifier gain-bandwidth product should include the necessary noise-gain margin and phase margin. Use the manufacturer’s recommended compensation for capacitive loading, and measure the completed channel for oscillation, output clipping, and settling under the actual source and load conditions.
Información de cumplimiento
No definitive RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified in the manufacturer product material. The LT1112IS8 is not identified as an AEC-Q100-qualified automotive option.