MAX232IDRG4 - 120kbit/s Dual RS-232 Transceiver | Texas Instruments
N.º de pieza: MAX232IDRG4 ✓ ActivoMAX232IDRG4 Descripción general
An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and a ±RS-232 physical link. The MAX232 belongs to the transceiver and line-driver hierarchy, where a transmitter translates low-voltage digital signals into RS-232 levels and a receiver converts RS-232 inputs back to logic levels. Its integrated charge pump supplies the positive and negative voltages required by the RS-232 standard without a separate bipolar power supply.
Key features include two EIA-232 drivers, two EIA-232 receivers, operation from one 5 V supply, a data rate up to 120 kbit/s, and low typical supply current of 8 mA. The 16-pin SOIC package provides a conventional surface-mount footprint suitable for industrial-control, instrumentation, and embedded communication equipment. Its operating temperature range extends from -40 °C to +85 °C.
The charge-pump architecture is central to operation. External capacitors connected to the C1 and C2 pins generate the positive rail used by the drivers, while the receiver side reconstructs the incoming signal referenced to ground. The device supports receiver input levels to ±30 V, providing useful transient headroom for a communication interface exposed to connected equipment or longer cable runs.
Typical applications include RS-232 links between microcontrollers and test equipment, industrial controllers communicating with service terminals, configuration interfaces for embedded systems, and instrumentation using legacy serial ports. The dual-channel arrangement can support two independent transmit or receive paths, although a particular RS-232 connection may use only one channel in each direction.
PCB design should prioritize short charge-pump capacitor connections and a clean return path. Place the 1.0 µF capacitors close to their designated pins, route the interface ground carefully, and keep unprotected RS-232 conductors away from sensitive clock and analog traces. Firmware must also avoid relying on RS-232 signal levels as a substitute for a formal device handshake.
This page combines the MAX232IDRG4 interface specifications, verified distributor listings, same-family drop-in alternatives, and practical PCB guidance. It is designed to help engineers identify suitable replacements, understand the charge-pump implementation, and plan an RS-232 interface before layout and prototype assembly.
Alternativas directas para MAX232IDRG4 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con MAX232IDRG4 (mismo factor de forma y huella) — difiere en Package, Maximum Data Rate, Product Type, ESD Protection, Interface Standard.
MAX232ACSE+T
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →MAX232ESE+
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →MAX232EIDR
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →MAX232ESE+
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →MAX232DRE4
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →MAX232IDRG4 Especificaciones
| Product Type | Dual RS-232 driver/receiver transceiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Maximum Data Rate | 120 kbit/s |
| Tensión de alimentación | 5 V |
| Corriente de alimentación | 8 mA typical |
| Receiver Input Levels | ±30 V maximum |
| Charge-Pump Capacitor Value | 1.0 µF |
| ESD Protection | Exceeds JESD |
| Rango de temperatura de funcionamiento | -40 °C to +85 °C |
| Encapsulado | 16-pin SOIC |
| Tipo de montaje | Surface mount |
| Standard | EIA-232 |
| Driver and Receiver Count | 2/2 full-duplex transceivers |
| Power Architecture | Single 5 V supply with integrated charge pump |
Configuración de pines de MAX232IDRG4
| Pin 1 | R1OUT — Receiver 1 output |
| Pin 2 | R2OUT — Receiver 2 output |
| Pin 3 | R1IN — Receiver 1 input |
| Pin 4 | R2IN — Receiver 2 input |
| Pin 5 | T1IN — Transmitter 1 logic input |
| Pin 6 | T2IN — Transmitter 2 logic input |
| Pin 7 | T1OUT — Transmitter 1 RS-232 output |
| Pin 8 | T2OUT — Transmitter 2 RS-232 output |
| Pin 9 | GND — Ground |
| Pin 10 | VCC — Positive supply input |
| Pin 11 | V- — Charge-pump negative voltage output |
| Pin 12 | V+ — Charge-pump positive voltage output |
| Pin 13 | C1+ — Charge-pump capacitor C1 positive terminal |
| Pin 14 | C1- — Charge-pump capacitor C1 negative terminal |
| Pin 15 | C2+ — Charge-pump capacitor C2 positive terminal |
| Pin 16 | C2- — Charge-pump capacitor C2 negative terminal |
Aplicaciones típicas
MAX232IDRG4 es adecuado para 6 aplicacións: Embedded System Service Console, Industrial Controller Interface, Instrumentation Data Port, FPGA Configuration Interface, Point-of-Sale and Peripheral Link, Robotics and Automation Diagnostics.
Embedded System Service Console
The MAX232IDRG4 suits an embedded controller that retains a legacy RS-232 service interface for configuration, diagnostics, and firmware recovery. Its two transmitters and two receivers support more than one serial channel when the host system needs separate paths, while the 120 kbit/s maximum rate is more than adequate for console traffic and short command sequences. A single 5 V supply simplifies integration with the controller’s existing power tree, and the integrated charge pump avoids a separate negative rail. Place the 1.0 µF capacitors close to their charge-pump pins and provide a low-impedance signal-ground return to the connector.
Recomendado
Industrial Controller Interface
The MAX232IDRG4 is appropriate for an industrial controller communicating with legacy test equipment, drives, or service units over RS-232. Its -40 °C to +85 °C operating range covers a broad range of industrial environments, while receiver input levels to ±30 V add useful margin for connected equipment. The 120 kbit/s rate supports short control packets and telemetry streams without requiring a separate line-power supply. Because an industrial enclosure may introduce ground offsets and cable transients, the design should combine careful interface grounding with chassis-level surge and ESD protection strategy appropriate to the installation.
Recomendado
Instrumentation Data Port
The MAX232IDRG4 can provide a compact RS-232 data port in laboratory or field instrumentation that must connect to a PC or service terminal. Its dual-driver and dual-receiver organization allows two transmit and two receive functions, making it useful for separate command and measurement channels. The low 8 mA typical supply current and single 5 V operation simplify power budgeting in portable instruments. At the same time, the 120 kbit/s rate and ±30 V receiver input capability support common RS-232 links without a bipolar supply, while PCB placement should isolate the interface from precision analog circuitry.
Recomendado
FPGA Configuration Interface
The MAX232IDRG4 is useful in an FPGA or microcontroller design that exposes a PC-facing configuration or diagnostic port. The MAX232IDRG4 handles the logic-to-RS-232 conversion while the controller manages the packet protocol, allowing firmware updates and runtime commands over a cable connection. Its 120 kbit/s rate is suitable for typical configuration files and diagnostic commands, and its single 5 V supply can operate directly from the logic rail. Keep charge-pump loops compact and route the interface return toward the connector ground rather than sharing narrow paths with switching currents.
Recomendado
Point-of-Sale and Peripheral Link
The MAX232IDRG4 can support a legacy point-of-sale terminal, peripheral controller, or service connector that uses RS-232 instead of a modern USB interface. The two transmitters and two receivers permit paired command and status channels when required, while the 5 V single-supply operation aligns with embedded peripheral electronics. The MAX232IDRG4’s 120 kbit/s rate is appropriate for short transaction messages and configuration exchanges. Designers should verify connector pin assignment, shield grounding, and software flow control because RS-232 levels alone do not provide handshake or transaction integrity.
Recomendado
Robotics and Automation Diagnostics
The MAX232IDRG4 provides a practical diagnostic link for robotics and automation equipment where technicians use a service laptop or handheld terminal. The 120 kbit/s rate supports command traffic, status polling, and short diagnostic packets, while the dual-channel arrangement can carry separate transmit and receive paths. Operation from one 5 V rail is advantageous in battery-backed or distributed controllers, and receiver operation to ±30 V improves tolerance to connected equipment. The interface should be grounded carefully at the chassis boundary, and cable ingress protection should be selected for the actual surge and ESD environment.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MAX232IDRG4 — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | MAX232ACSE+ | MAX232ESE+ | MAX232EIDR | MAX232ESE | MAX232DRE |
|---|---|---|---|---|---|---|
| Package | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Transceiver Configuration | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers |
| Maximum Data Rate | 120 kbit/s | 120 kbit/s | 120 kbit/s | 120 kbit/s | 120 kbit/s | 120 kbit/s |
| Supply Voltage | 5 V single supply | 5 V single supply | 5 V single supply | 5 V single supply | 5 V single supply | 5 V single supply |
| Charge-Pump Capacitor | 1.0 µF | 1.0 µF | 1.0 µF | 1.0 µF | 1.0 µF | 1.0 µF |
| Receiver Input Levels | ±30 V maximum | ±30 V maximum | ±30 V maximum | ±30 V maximum | ±30 V maximum | ±30 V maximum |
Diferenciadores clave
- Maintains the established MAX232 dual-channel interface without a bipolar supply (frente a MAX232ESE+)
- Supports conventional RS-232 service ports with 120 kbit/s signaling (frente a MAX232EIDR)
- Combines integrated charge-pump conversion with a 16-pin SOIC footprint (frente a MAX232ACSE+)
Notas de diseño
Place both 1.0 µF charge-pump capacitors close to the C1 and C2 pins, with the shortest possible tracks and minimal loop area. Maintain the polarity and connections shown in the manufacturer application circuit. Keep these switching paths away from receiver inputs and sensitive analog traces, and provide a continuous ground reference beneath the interface section.
Route the two RS-232 driver outputs directly toward the connector without sharp stubs, while keeping the logic-side transmitter inputs and receiver outputs away from the cable side of the board. Provide a solid ground return associated with the cable shield. Where the connector is chassis-mounted, follow the equipment’s established chassis, surge, and isolation design rather than treating the IC’s internal ESD protection as complete lightning protection.
Do not replace the specified charge-pump capacitors with arbitrary values or omit the capacitor polarity. Do not assume that ±30 V receiver input capability eliminates the need for external surge protection on long or outdoor cables. Also avoid treating an RS-232 connection as a guaranteed isolated interface; verify whether the equipment requires galvanic isolation for safety or ground-potential reasons.
Información de cumplimiento
The manufacturer datasheet excerpt states that ESD protection exceeds JESD. Exact RoHS, REACH, lead-free, halogen-free, conflict-minerals, and AEC-Q100 declarations require confirmation from the current Texas Instruments product documentation.