MAX232IDRG4 - 120kbit/s Dual RS-232 Transceiver | Texas Instruments
料号: MAX232IDRG4 ✓ 量产中MAX232IDRG4 概述
An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and a ±RS-232 physical link. The MAX232 belongs to the transceiver and line-driver hierarchy, where a transmitter translates low-voltage digital signals into RS-232 levels and a receiver converts RS-232 inputs back to logic levels. Its integrated charge pump supplies the positive and negative voltages required by the RS-232 standard without a separate bipolar power supply.
Key features include two EIA-232 drivers, two EIA-232 receivers, operation from one 5 V supply, a data rate up to 120 kbit/s, and low typical supply current of 8 mA. The 16-pin SOIC package provides a conventional surface-mount footprint suitable for industrial-control, instrumentation, and embedded communication equipment. Its operating temperature range extends from -40 °C to +85 °C.
The charge-pump architecture is central to operation. External capacitors connected to the C1 and C2 pins generate the positive rail used by the drivers, while the receiver side reconstructs the incoming signal referenced to ground. The device supports receiver input levels to ±30 V, providing useful transient headroom for a communication interface exposed to connected equipment or longer cable runs.
Typical applications include RS-232 links between microcontrollers and test equipment, industrial controllers communicating with service terminals, configuration interfaces for embedded systems, and instrumentation using legacy serial ports. The dual-channel arrangement can support two independent transmit or receive paths, although a particular RS-232 connection may use only one channel in each direction.
PCB design should prioritize short charge-pump capacitor connections and a clean return path. Place the 1.0 µF capacitors close to their designated pins, route the interface ground carefully, and keep unprotected RS-232 conductors away from sensitive clock and analog traces. Firmware must also avoid relying on RS-232 signal levels as a substitute for a formal device handshake.
This page combines the MAX232IDRG4 interface specifications, verified distributor listings, same-family drop-in alternatives, and practical PCB guidance. It is designed to help engineers identify suitable replacements, understand the charge-pump implementation, and plan an RS-232 interface before layout and prototype assembly.
直接替换替代料: MAX232IDRG4 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MAX232IDRG4 (相同外形与封装尺寸) ——差异在于 Package, Maximum Data Rate, Product Type, ESD Protection, Interface Standard.
MAX232ACSE+T
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX232ESE+
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX232EIDR
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX232ESE+
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX232DRE4
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX232IDRG4 规格参数
| Product Type | Dual RS-232 driver/receiver transceiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Maximum Data Rate | 120 kbit/s |
| 电源电压 | 5 V |
| 电源电流 | 8 mA typical |
| Receiver Input Levels | ±30 V maximum |
| Charge-Pump Capacitor Value | 1.0 µF |
| ESD Protection | Exceeds JESD |
| 工作温度范围 | -40 °C to +85 °C |
| 封装 | 16-pin SOIC |
| 安装类型 | Surface mount |
| Standard | EIA-232 |
| Driver and Receiver Count | 2/2 full-duplex transceivers |
| Power Architecture | Single 5 V supply with integrated charge pump |
MAX232IDRG4 引脚配置
| 引脚 1 | R1OUT — Receiver 1 output |
| 引脚 2 | R2OUT — Receiver 2 output |
| 引脚 3 | R1IN — Receiver 1 input |
| 引脚 4 | R2IN — Receiver 2 input |
| 引脚 5 | T1IN — Transmitter 1 logic input |
| 引脚 6 | T2IN — Transmitter 2 logic input |
| 引脚 7 | T1OUT — Transmitter 1 RS-232 output |
| 引脚 8 | T2OUT — Transmitter 2 RS-232 output |
| 引脚 9 | GND — Ground |
| 引脚 10 | VCC — Positive supply input |
| 引脚 11 | V- — Charge-pump negative voltage output |
| 引脚 12 | V+ — Charge-pump positive voltage output |
| 引脚 13 | C1+ — Charge-pump capacitor C1 positive terminal |
| 引脚 14 | C1- — Charge-pump capacitor C1 negative terminal |
| 引脚 15 | C2+ — Charge-pump capacitor C2 positive terminal |
| 引脚 16 | C2- — Charge-pump capacitor C2 negative terminal |
典型应用
MAX232IDRG4 适用于 6 应用s: Embedded System Service Console, Industrial Controller Interface, Instrumentation Data Port, FPGA Configuration Interface, Point-of-Sale and Peripheral Link, Robotics and Automation Diagnostics.
Embedded System Service Console
The MAX232IDRG4 suits an embedded controller that retains a legacy RS-232 service interface for configuration, diagnostics, and firmware recovery. Its two transmitters and two receivers support more than one serial channel when the host system needs separate paths, while the 120 kbit/s maximum rate is more than adequate for console traffic and short command sequences. A single 5 V supply simplifies integration with the controller’s existing power tree, and the integrated charge pump avoids a separate negative rail. Place the 1.0 µF capacitors close to their charge-pump pins and provide a low-impedance signal-ground return to the connector.
推荐
Industrial Controller Interface
The MAX232IDRG4 is appropriate for an industrial controller communicating with legacy test equipment, drives, or service units over RS-232. Its -40 °C to +85 °C operating range covers a broad range of industrial environments, while receiver input levels to ±30 V add useful margin for connected equipment. The 120 kbit/s rate supports short control packets and telemetry streams without requiring a separate line-power supply. Because an industrial enclosure may introduce ground offsets and cable transients, the design should combine careful interface grounding with chassis-level surge and ESD protection strategy appropriate to the installation.
推荐
Instrumentation Data Port
The MAX232IDRG4 can provide a compact RS-232 data port in laboratory or field instrumentation that must connect to a PC or service terminal. Its dual-driver and dual-receiver organization allows two transmit and two receive functions, making it useful for separate command and measurement channels. The low 8 mA typical supply current and single 5 V operation simplify power budgeting in portable instruments. At the same time, the 120 kbit/s rate and ±30 V receiver input capability support common RS-232 links without a bipolar supply, while PCB placement should isolate the interface from precision analog circuitry.
推荐
FPGA Configuration Interface
The MAX232IDRG4 is useful in an FPGA or microcontroller design that exposes a PC-facing configuration or diagnostic port. The MAX232IDRG4 handles the logic-to-RS-232 conversion while the controller manages the packet protocol, allowing firmware updates and runtime commands over a cable connection. Its 120 kbit/s rate is suitable for typical configuration files and diagnostic commands, and its single 5 V supply can operate directly from the logic rail. Keep charge-pump loops compact and route the interface return toward the connector ground rather than sharing narrow paths with switching currents.
推荐
Point-of-Sale and Peripheral Link
The MAX232IDRG4 can support a legacy point-of-sale terminal, peripheral controller, or service connector that uses RS-232 instead of a modern USB interface. The two transmitters and two receivers permit paired command and status channels when required, while the 5 V single-supply operation aligns with embedded peripheral electronics. The MAX232IDRG4’s 120 kbit/s rate is appropriate for short transaction messages and configuration exchanges. Designers should verify connector pin assignment, shield grounding, and software flow control because RS-232 levels alone do not provide handshake or transaction integrity.
推荐
Robotics and Automation Diagnostics
The MAX232IDRG4 provides a practical diagnostic link for robotics and automation equipment where technicians use a service laptop or handheld terminal. The 120 kbit/s rate supports command traffic, status polling, and short diagnostic packets, while the dual-channel arrangement can carry separate transmit and receive paths. Operation from one 5 V rail is advantageous in battery-backed or distributed controllers, and receiver operation to ±30 V improves tolerance to connected equipment. The interface should be grounded carefully at the chassis boundary, and cable ingress protection should be selected for the actual surge and ESD environment.
推荐
推荐产品汇总
工程参考数据: MAX232IDRG4 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX232ACSE+ | MAX232ESE+ | MAX232EIDR | MAX232ESE | MAX232DRE |
|---|---|---|---|---|---|---|
| Package | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Transceiver Configuration | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers |
| Maximum Data Rate | 120 kbit/s | 120 kbit/s | 120 kbit/s | 120 kbit/s | 120 kbit/s | 120 kbit/s |
| Supply Voltage | 5 V single supply | 5 V single supply | 5 V single supply | 5 V single supply | 5 V single supply | 5 V single supply |
| Charge-Pump Capacitor | 1.0 µF | 1.0 µF | 1.0 µF | 1.0 µF | 1.0 µF | 1.0 µF |
| Receiver Input Levels | ±30 V maximum | ±30 V maximum | ±30 V maximum | ±30 V maximum | ±30 V maximum | ±30 V maximum |
关键差异点
- Maintains the established MAX232 dual-channel interface without a bipolar supply (对比 MAX232ESE+)
- Supports conventional RS-232 service ports with 120 kbit/s signaling (对比 MAX232EIDR)
- Combines integrated charge-pump conversion with a 16-pin SOIC footprint (对比 MAX232ACSE+)
设计说明
Place both 1.0 µF charge-pump capacitors close to the C1 and C2 pins, with the shortest possible tracks and minimal loop area. Maintain the polarity and connections shown in the manufacturer application circuit. Keep these switching paths away from receiver inputs and sensitive analog traces, and provide a continuous ground reference beneath the interface section.
Route the two RS-232 driver outputs directly toward the connector without sharp stubs, while keeping the logic-side transmitter inputs and receiver outputs away from the cable side of the board. Provide a solid ground return associated with the cable shield. Where the connector is chassis-mounted, follow the equipment’s established chassis, surge, and isolation design rather than treating the IC’s internal ESD protection as complete lightning protection.
Do not replace the specified charge-pump capacitors with arbitrary values or omit the capacitor polarity. Do not assume that ±30 V receiver input capability eliminates the need for external surge protection on long or outdoor cables. Also avoid treating an RS-232 connection as a guaranteed isolated interface; verify whether the equipment requires galvanic isolation for safety or ground-potential reasons.
合规信息
The manufacturer datasheet excerpt states that ESD protection exceeds JESD. Exact RoHS, REACH, lead-free, halogen-free, conflict-minerals, and AEC-Q100 declarations require confirmation from the current Texas Instruments product documentation.