MAX3221IDBRE4 - 250kbps RS-232 Transceiver | Texas Instruments
N.º de pieza: MAX3221IDBRE4 ✓ ActivoMAX3221IDBRE4 Descripción general
An RS-232 transceiver is an interface IC that converts between single-ended logic signals and the bipolar voltage levels used by RS-232 equipment. The MAX3221 belongs to the line-driver and receiver hierarchy within interface ICs, where it sits between a host controller and an external serial connector. Its charge-pump circuitry generates the positive and negative voltages required by the RS-232 transmitter without a separate negative supply.
Key features include operation from 3 V to 5.5 V, a maximum data rate of 250 kbps, and ±15 kV human-body-model ESD protection on the serial-port connection pins, including ground. The receiver supports a dedicated enable input, while the device maintains a typical 1 µA standby current. Four external 0.1 µF charge-pump capacitors support the internal voltage conversion, and 5 V logic inputs are accepted with a 3.3 V supply.
The MAX3221 implements one half-duplex RS-232 channel, combining a transmitter and receiver in a compact package. Its internal dual charge pump produces the bipolar signal levels required by TIA/EIA-232-F and ITU V.28 interfaces. The target MAX3221IDBRE4 ordering code identifies the 16-pin SSOP configuration, allowing placement with surface-mount assembly while preserving a conventional narrow-body footprint.
Typical uses include single-port serial diagnostics, point-of-sale equipment, industrial control links, embedded service interfaces, and legacy peripheral connections. The 250 kbps capability supports low- and moderate-speed serial links, while the dual supply range permits operation from both 3.3 V and 5 V systems. The low standby current is useful when equipment must retain a receive path without continuously loading the supply.
Circuit design should preserve the charge-pump capacitor connections, place the four 0.1 µF capacitors close to their associated pins, and route the RS-232 connector and protected serial lines away from sensitive analog and high-speed digital traces. Confirm logic thresholds, signal polarity, flow control, and connector grounding before replacing an existing interface design.
This product overview combines the manufacturer's electrical characteristics, package information, interface standards, ESD capability, and practical implementation guidance with engineering-focused comparisons for drop-in device selection.
Alternativas directas para MAX3221IDBRE4 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con MAX3221IDBRE4 (mismo factor de forma y huella) — difiere en External Charge-Pump Capacitors, Package, Product Type, Supply Voltage Range, ESD Protection.
MAX3221IDBR
✅ Sustitución directaConsulte el precio
Ver hoja de datos →MAX3221EIDB
✅ Sustitución directaConsulte el precio
Ver hoja de datos →MAX3221IDBRE4 Especificaciones
| Product Type | Single-channel RS-232 line driver and receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| Number of Drivers | 1 |
| Number of Receivers | 1 |
| Driver and Receiver Configuration | 1/1 full RS-232 transceiver |
| ESD Protection | ±15 kV HBM |
| Standby Current | 1 µA typical |
| External Charge-Pump Capacitors | 4 × 0.1 µF |
| 5 V Logic Input Compatibility | 5 V logic input accepted with 3.3 V supply |
| RS-232 Standards | TIA/EIA-232-F and ITU V.28 |
| Encapsulado | 16-pin SSOP |
| Package Width | 5.30 mm |
| Tipo de montaje | Surface mount |
| Receiver Enable | Dedicated enable input |
Guía de configuración de pines de MAX3221IDBRE4 5.30 mm
Configuración de pines para MAX3221IDBRE4 (encapsulado 5.30 mm). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para MAX3221IDBRE4.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
MAX3221IDBRE4 es adecuado para 6 aplicacións: Industrial Diagnostic Serial Port, Point-of-Sale Terminal Connectivity, Embedded Equipment Service Console, Legacy Peripheral Data Link, IoT Gateway Maintenance Port, Instrument Control Connection.
Industrial Diagnostic Serial Port
The MAX3221IDBRE4 suits a single industrial diagnostic connection because it combines one RS-232 driver, one receiver, and a 250 kbps maximum data rate in a 16-pin SSOP package. Operating from 3 V to 5.5 V permits integration with embedded 3.3 V controllers and legacy 5 V service equipment. Its ±15 kV HBM ESD protection on the connector-facing pins adds useful defense for a cable-connected port, although industrial surge requirements should be assessed separately. The receiver enable input allows the host to control when received data is presented, while four 0.1 µF charge-pump capacitors support the internal bipolar voltage generation.
Recomendado
Point-of-Sale Terminal Connectivity
The MAX3221IDBRE4 provides a compact interface between a point-of-sale controller and a legacy RS-232 peripheral. Its single-channel architecture is appropriate when the terminal manages one serial device, while the 250 kbps rate covers common receipt-printer and service-port traffic. The 3 V to 5.5 V operating range supports both modern 3.3 V logic systems and 5 V equipment interfaces, and the receiver accepts 5 V logic input with a 3.3 V supply. The 16-pin SSOP package helps limit board area, while the dedicated receiver enable can suppress an unwanted receiver output during reset or firmware update periods.
Recomendado
Embedded Equipment Service Console
The MAX3221IDBRE4 can provide a service-console link between an embedded controller and a laptop or configuration tool. Its 250 kbps maximum rate is suitable for command exchanges, boot logs, firmware downloads, and diagnostic commands rather than continuous high-throughput data. The device accepts a supply from 3 V to 5.5 V and uses a typical 1 µA standby current, making it useful in equipment that periodically powers or disables its service interface. Connector-side ±15 kV HBM ESD protection helps manage electrostatic discharge encountered during routine cable handling, but cable routing and grounding remain essential.
Recomendado
Legacy Peripheral Data Link
The MAX3221IDBRE4 bridges modern controller logic to a legacy RS-232 peripheral when only one unidirectional or half-duplex channel is required. It converts the controller's logic levels into RS-232-compatible signals and provides a receiver for incoming data, with operation supported through 250 kbps. Its 16-pin SSOP package is useful where a through-hole transceiver would consume excessive board area. The three-to-four external 0.1 µF capacitors should be positioned close to the charge-pump pins, and the serial route should remain separated from clocks, sensor analog signals, and switching-power nodes.
Recomendado
IoT Gateway Maintenance Port
The MAX3221IDBRE4 can serve as the maintenance and configuration interface for an IoT gateway, smart controller, or network appliance that supports RS-232 service access. The 3 V to 5.5 V supply range fits widely used embedded processing rails, and 250 kbps is sufficient for startup logs, configuration transfer, and remote diagnostics. The receiver enable supports controlled connection behavior, and the low typical standby current of 1 µA helps when the gateway periodically isolates its maintenance interface. For outdoor or remotely deployed equipment, add environmental isolation and surge protection as required by the installation.
Recomendado
Instrument Control Connection
The MAX3221IDBRE4 is suitable for controlling or reading a single legacy serial instrument from an embedded test system. The 250 kbps limit supports typical command-response instrument protocols, and the 16-pin SSOP package simplifies integration into compact controller boards. A 3.3 V or 5 V host can operate the interface within the stated 3 V to 5.5 V supply range, including systems that need 5 V-compatible logic inputs. The connector-facing ±15 kV HBM protection improves robustness, although long instrument cables may require additional protection. The four charge-pump capacitors must follow the manufacturer's layout and component guidance.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MAX3221IDBRE4 — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | MAX3221IDBR | MAX3221EIDB |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-pin SSOP | 16-pin SSOP - same | 16-pin SSOP - same |
| Device Type | Single-channel RS-232 transceiver | Single-channel RS-232 transceiver | MAX3221-family RS-232 transceiver |
Diferenciadores clave
- Combines a complete single-channel interface in a narrow SSOP package (frente a MAX3221IDBR)
- Uses a low-power 1 µA typical standby state (frente a MAX3221EIDB)
- Provides connector-side HBM ESD protection (frente a MAX3221EIDB)
Notas de diseño
Place the four 0.1 µF charge-pump capacitors directly beside their corresponding IC pins and maintain short, symmetric return paths. Follow the capacitor connections and polarity shown in the manufacturer datasheet. Keep the exposed connector-side traces away from clocks, precision analog inputs, and switching-regulator power loops to reduce capacitive coupling and ground-current injection into sensitive circuitry.
Route the RS-232 driver output directly toward the connector and keep the receiver input away from switching nodes and high-current return paths. Ground the connector shield according to the equipment's EMC strategy, and use the MAX3221 ground pin as the device reference. Do not route the cable-side interface through areas carrying unrelated high-speed signals, since both edge coupling and ground bounce can corrupt the receiver threshold.
Confirm that the replacement ordering code preserves the 16-pin SSOP footprint, receiver-enable behavior, temperature grade, and tape-and-reel orientation. Related MAX3221 and ICL3221 family numbers may differ in pin assignment, package construction, or qualification even when their headlines appear similar. Also verify that the host accepts the receiver output when disabled and that logic thresholds remain valid at the selected 3.3 V or 5 V supply.
For equipment with an externally accessible RS-232 connector, treat the MAX3221's ±15 kV HBM rating as device-level ESD protection rather than a complete industrial surge solution. Add appropriately rated external protection when the port can experience lightning, large motor transients, or severe conducted disturbances. Bond the connector shield and enclosure reference in accordance with the product's grounding architecture to prevent cable-borne energy from entering the logic ground.
Información de cumplimiento
The device meets TIA/EIA-232-F and ITU V.28 interface requirements. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer product or quality documentation.