MAX3221IDBRE4 - 250kbps RS-232 Transceiver | Texas Instruments
MPN: MAX3221IDBRE4 ✓ 啟用中MAX3221IDBRE4 概覽
An RS-232 transceiver is an interface IC that converts between single-ended logic signals and the bipolar voltage levels used by RS-232 equipment. The MAX3221 belongs to the line-driver and receiver hierarchy within interface ICs, where it sits between a host controller and an external serial connector. Its charge-pump circuitry generates the positive and negative voltages required by the RS-232 transmitter without a separate negative supply.
Key features include operation from 3 V to 5.5 V, a maximum data rate of 250 kbps, and ±15 kV human-body-model ESD protection on the serial-port connection pins, including ground. The receiver supports a dedicated enable input, while the device maintains a typical 1 µA standby current. Four external 0.1 µF charge-pump capacitors support the internal voltage conversion, and 5 V logic inputs are accepted with a 3.3 V supply.
The MAX3221 implements one half-duplex RS-232 channel, combining a transmitter and receiver in a compact package. Its internal dual charge pump produces the bipolar signal levels required by TIA/EIA-232-F and ITU V.28 interfaces. The target MAX3221IDBRE4 ordering code identifies the 16-pin SSOP configuration, allowing placement with surface-mount assembly while preserving a conventional narrow-body footprint.
Typical uses include single-port serial diagnostics, point-of-sale equipment, industrial control links, embedded service interfaces, and legacy peripheral connections. The 250 kbps capability supports low- and moderate-speed serial links, while the dual supply range permits operation from both 3.3 V and 5 V systems. The low standby current is useful when equipment must retain a receive path without continuously loading the supply.
Circuit design should preserve the charge-pump capacitor connections, place the four 0.1 µF capacitors close to their associated pins, and route the RS-232 connector and protected serial lines away from sensitive analog and high-speed digital traces. Confirm logic thresholds, signal polarity, flow control, and connector grounding before replacing an existing interface design.
This product overview combines the manufacturer's electrical characteristics, package information, interface standards, ESD capability, and practical implementation guidance with engineering-focused comparisons for drop-in device selection.
直接替換替代品,適用於 MAX3221IDBRE4 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MAX3221IDBRE4 (相同外形與佔位) — 差異在於 External Charge-Pump Capacitors, Package, Product Type, Supply Voltage Range, ESD Protection.
MAX3221IDBR
✅ 直接替換聯絡詢價
查看資料表 →MAX3221EIDB
✅ 直接替換聯絡詢價
查看資料表 →MAX3221IDBRE4 規格
| Product Type | Single-channel RS-232 line driver and receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| Number of Drivers | 1 |
| Number of Receivers | 1 |
| Driver and Receiver Configuration | 1/1 full RS-232 transceiver |
| ESD Protection | ±15 kV HBM |
| Standby Current | 1 µA typical |
| External Charge-Pump Capacitors | 4 × 0.1 µF |
| 5 V Logic Input Compatibility | 5 V logic input accepted with 3.3 V supply |
| RS-232 Standards | TIA/EIA-232-F and ITU V.28 |
| 封裝 | 16-pin SSOP |
| Package Width | 5.30 mm |
| 安裝類型 | Surface mount |
| Receiver Enable | Dedicated enable input |
MAX3221IDBRE4 5.30 mm 腳位配置指南
MAX3221IDBRE4(5.30 mm 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: MAX3221IDBRE4.
請參閱 資料表 以查看完整腳位配置。
典型應用
MAX3221IDBRE4 適用於 6 應用s: Industrial Diagnostic Serial Port, Point-of-Sale Terminal Connectivity, Embedded Equipment Service Console, Legacy Peripheral Data Link, IoT Gateway Maintenance Port, Instrument Control Connection.
Industrial Diagnostic Serial Port
The MAX3221IDBRE4 suits a single industrial diagnostic connection because it combines one RS-232 driver, one receiver, and a 250 kbps maximum data rate in a 16-pin SSOP package. Operating from 3 V to 5.5 V permits integration with embedded 3.3 V controllers and legacy 5 V service equipment. Its ±15 kV HBM ESD protection on the connector-facing pins adds useful defense for a cable-connected port, although industrial surge requirements should be assessed separately. The receiver enable input allows the host to control when received data is presented, while four 0.1 µF charge-pump capacitors support the internal bipolar voltage generation.
推薦
Point-of-Sale Terminal Connectivity
The MAX3221IDBRE4 provides a compact interface between a point-of-sale controller and a legacy RS-232 peripheral. Its single-channel architecture is appropriate when the terminal manages one serial device, while the 250 kbps rate covers common receipt-printer and service-port traffic. The 3 V to 5.5 V operating range supports both modern 3.3 V logic systems and 5 V equipment interfaces, and the receiver accepts 5 V logic input with a 3.3 V supply. The 16-pin SSOP package helps limit board area, while the dedicated receiver enable can suppress an unwanted receiver output during reset or firmware update periods.
推薦
Embedded Equipment Service Console
The MAX3221IDBRE4 can provide a service-console link between an embedded controller and a laptop or configuration tool. Its 250 kbps maximum rate is suitable for command exchanges, boot logs, firmware downloads, and diagnostic commands rather than continuous high-throughput data. The device accepts a supply from 3 V to 5.5 V and uses a typical 1 µA standby current, making it useful in equipment that periodically powers or disables its service interface. Connector-side ±15 kV HBM ESD protection helps manage electrostatic discharge encountered during routine cable handling, but cable routing and grounding remain essential.
推薦
Legacy Peripheral Data Link
The MAX3221IDBRE4 bridges modern controller logic to a legacy RS-232 peripheral when only one unidirectional or half-duplex channel is required. It converts the controller's logic levels into RS-232-compatible signals and provides a receiver for incoming data, with operation supported through 250 kbps. Its 16-pin SSOP package is useful where a through-hole transceiver would consume excessive board area. The three-to-four external 0.1 µF capacitors should be positioned close to the charge-pump pins, and the serial route should remain separated from clocks, sensor analog signals, and switching-power nodes.
推薦
IoT Gateway Maintenance Port
The MAX3221IDBRE4 can serve as the maintenance and configuration interface for an IoT gateway, smart controller, or network appliance that supports RS-232 service access. The 3 V to 5.5 V supply range fits widely used embedded processing rails, and 250 kbps is sufficient for startup logs, configuration transfer, and remote diagnostics. The receiver enable supports controlled connection behavior, and the low typical standby current of 1 µA helps when the gateway periodically isolates its maintenance interface. For outdoor or remotely deployed equipment, add environmental isolation and surge protection as required by the installation.
推薦
Instrument Control Connection
The MAX3221IDBRE4 is suitable for controlling or reading a single legacy serial instrument from an embedded test system. The 250 kbps limit supports typical command-response instrument protocols, and the 16-pin SSOP package simplifies integration into compact controller boards. A 3.3 V or 5 V host can operate the interface within the stated 3 V to 5.5 V supply range, including systems that need 5 V-compatible logic inputs. The connector-facing ±15 kV HBM protection improves robustness, although long instrument cables may require additional protection. The four charge-pump capacitors must follow the manufacturer's layout and component guidance.
推薦
推薦產品摘要
工程參考資料,適用於 MAX3221IDBRE4 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MAX3221IDBR | MAX3221EIDB |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-pin SSOP | 16-pin SSOP - same | 16-pin SSOP - same |
| Device Type | Single-channel RS-232 transceiver | Single-channel RS-232 transceiver | MAX3221-family RS-232 transceiver |
主要差異化特點
- Combines a complete single-channel interface in a narrow SSOP package (對比MAX3221IDBR)
- Uses a low-power 1 µA typical standby state (對比MAX3221EIDB)
- Provides connector-side HBM ESD protection (對比MAX3221EIDB)
設計說明
Place the four 0.1 µF charge-pump capacitors directly beside their corresponding IC pins and maintain short, symmetric return paths. Follow the capacitor connections and polarity shown in the manufacturer datasheet. Keep the exposed connector-side traces away from clocks, precision analog inputs, and switching-regulator power loops to reduce capacitive coupling and ground-current injection into sensitive circuitry.
Route the RS-232 driver output directly toward the connector and keep the receiver input away from switching nodes and high-current return paths. Ground the connector shield according to the equipment's EMC strategy, and use the MAX3221 ground pin as the device reference. Do not route the cable-side interface through areas carrying unrelated high-speed signals, since both edge coupling and ground bounce can corrupt the receiver threshold.
Confirm that the replacement ordering code preserves the 16-pin SSOP footprint, receiver-enable behavior, temperature grade, and tape-and-reel orientation. Related MAX3221 and ICL3221 family numbers may differ in pin assignment, package construction, or qualification even when their headlines appear similar. Also verify that the host accepts the receiver output when disabled and that logic thresholds remain valid at the selected 3.3 V or 5 V supply.
For equipment with an externally accessible RS-232 connector, treat the MAX3221's ±15 kV HBM rating as device-level ESD protection rather than a complete industrial surge solution. Add appropriately rated external protection when the port can experience lightning, large motor transients, or severe conducted disturbances. Bond the connector shield and enclosure reference in accordance with the product's grounding architecture to prevent cable-borne energy from entering the logic ground.
合規資訊
The device meets TIA/EIA-232-F and ITU V.28 interface requirements. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer product or quality documentation.