MAX3243ECAI+T - 3/5 RS-232 Transceiver, 15kV ESD | Analog Devices
N.º de pieza: MAX3243ECAI+T ✓ ActivoMAX3243ECAI+T Descripción general
An RS-232 transceiver is an interface IC that converts logic-level signals between a host controller and RS-232 differential line drivers and receivers. The MAX3243 belongs to the hierarchy of interface ICs, serial-interface transceivers, RS-232 communications devices, and semiconductors. It allows a modern low-voltage controller to communicate with legacy RS-232 equipment without requiring external ±12V power rails.
The MAX3243 integrates three RS-232 line drivers, five receivers, and a dual charge-pump circuit. Its 3.0V-to-5.5V single-supply operation supports both 3.3V and 5V systems. An internal charge pump generates the bipolar voltage required by RS-232 transmitters, while enhanced electrostatic-discharge protection improves resilience when cables are connected to external equipment. The E suffix identifies the enhanced ESD version, and the CAI suffix denotes the 28-pin SSOP configuration with a commercial temperature grade.
Automatic shutdown is a significant benefit in portable and low-power equipment. According to the manufacturer product page, the MAX3243 can reach a 1µA supply current when AutoShutdown is active and no valid signal appears at the receiver inputs. The device can wake automatically when receiver activity resumes, or shutdown can be controlled in software, allowing the interface to remain transparent to normal serial-port operation.
Typical uses include industrial serial adapters, point-of-sale equipment, data-acquisition systems, test instrumentation, and embedded controllers that must connect to RS-232 peripherals. Three drivers allow transmission on as many as three lines, while five receivers support monitoring of five incoming signals. The 250kbps capability exceeds the speed required by many legacy serial protocols and is useful for short-distance point-to-point links.
PCB design should keep charge-pump and high-voltage driver traces away from sensitive receiver and logic-ground paths. Place the required bypass capacitors close to their supply and ground pins, route connector-side signals according to the manufacturer pinout, and provide chassis grounding or surge-protection components where cables leave the enclosure. Confirm the receiver's active polarity and AutoShutdown timing in firmware before replacing a conventional RS-232 implementation.
This product record combines the manufacturer specifications, exact-package identification, lifecycle information, sourcing context, and drop-in alternatives with practical guidance for layout, power management, and signal-integrity review.
Alternativas directas para MAX3243ECAI+T — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con MAX3243ECAI+T (mismo factor de forma y huella) — difiere en Product Type, ESD Protection, Supply Voltage Range, Interface Standard, Package.
MAX3243CAI+T
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MAX3243EEAI+
✅ Sustitución directaConsulte el precio
Ver hoja de datos →MAX3243ECAI+
✅ Sustitución directaConsulte el precio
Ver hoja de datos →MAX3243ECAI+G2X
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MAX3243ECAI+T Especificaciones
| Product Type | RS-232 line driver and receiver transceiver |
| Number of Drivers | 3 drivers |
| Number of Receivers | 5 receivers |
| Supply Voltage Range | 3.0V to 5.5V |
| Maximum Data Rate | 250kbps |
| ESD Protection | ±15kV HBM |
| AutoShutdown Supply Current | 1µA |
| Charge-Pump Circuit | Dual charge pump |
| Interface Standard | RS-232 / EIA/TIA-232 |
| Signaling Standard | V.28 / V.24 |
| Encapsulado | 28-pin SSOP |
| Package Pin Count | 28 pins |
| Tipo de montaje | Surface mount |
| Automotive Qualification | Not applicable |
Guía de configuración de pines de MAX3243ECAI+T 28 pins
Configuración de pines para MAX3243ECAI+T (encapsulado 28 pins). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para MAX3243ECAI+T.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
MAX3243ECAI+T es adecuado para 6 aplicacións: Industrial Serial Port Interface, Point-of-Sale Terminal Connectivity, Data Acquisition and Instrumentation, Embedded Equipment Controller, Network Equipment Serial Console, Portable Measurement and Control Device.
Industrial Serial Port Interface
The MAX3243ECAI+T fits industrial controllers that must communicate with RS-232 test equipment, programmable instruments, or legacy factory peripherals. Its three drivers support multiple outbound control signals, while five receivers can monitor acknowledgements, status lines, and sensor data. Operation from 3.0V to 5.5V removes external ±12V supplies, and the integrated dual charge pump simplifies the power architecture. The ±15kV HBM protection rating strengthens the connector-side interface when cables can be handled by operators. Automatic shutdown can also reduce standby consumption when the peripheral remains idle.
Recomendado
Point-of-Sale Terminal Connectivity
The MAX3243ECAI+T is appropriate for point-of-sale terminals, receipt printers, card-reader accessories, and service consoles that use RS-232 links. Three transmit channels can carry commands and data, while five receive channels provide enough monitoring points for printer status, transaction completion, and fault signaling. Its 3.3V-to-5V supply flexibility simplifies compatibility with embedded host processors. Because many peripheral ports remain idle between transactions, AutoShutdown and automatic wake-up can reduce system power without requiring the host to manage external RS-232 transceiver power rails.
Recomendado
Data Acquisition and Instrumentation
The MAX3243ECAI+T is suitable for data-acquisition units and laboratory instruments that expose a legacy RS-232 management port. The 250kbps maximum rate supports many short-distance control and status protocols, while five receivers allow the instrument to report multiple digital conditions to a host controller. The single 3.0V-to-5.5V supply is useful where a ±12V rail is undesirable, and the internal charge pump provides compliant RS-232 levels. Its enhanced ESD protection is valuable for bench equipment, although protective grounding and cable shielding should still follow the enclosure design.
Recomendado
Embedded Equipment Controller
The MAX3243ECAI+T fits embedded service equipment that must communicate with external RS-232 accessories while running from a 3.3V or 5V system rail. Three drivers permit command, configuration, and data channels, while five receivers provide flexible status monitoring. The device avoids the size and power cost of external charge-pump hardware. For equipment that spends substantial time disconnected from a cable, AutoShutdown can reduce supply demand to as little as 1µA, while receiver-triggered wake-up preserves transparent serial behavior. Firmware should allow sufficient settling time after a no-activity transition.
Recomendado
Network Equipment Serial Console
The MAX3243ECAI+T can provide a service or management console interface for routers, switches, and other network appliances that retain RS-232 diagnostics. Three transmit channels and five receive channels support console commands plus hardware status monitoring, and 250kbps is suitable for conventional terminal sessions. The 3.0V-to-5.5V operating range integrates readily with modern embedded processors. Automatic shutdown is advantageous for access ports that are not continuously connected, while the ±15kV HBM protection rating helps manage ESD introduced through service cables. Protect the enclosure entry and ground chassis appropriately for the installation environment.
Recomendado
Portable Measurement and Control Device
The MAX3243ECAI+T is well suited to portable measurement and control products that communicate with external sensors, fixtures, or service tools over RS-232. The single 3.0V-to-5.5V supply is compatible with common portable-system rails, while the dual charge pump avoids external high-voltage components. Three drivers and five receivers support richer control links than a basic one-driver, one-receiver interface. When no valid receiver activity is detected, AutoShutdown can lower consumption to 1µA, extending standby time. Wake-up latency and the cable’s ground reference must be checked against the operating scenario.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MAX3243ECAI+T — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | MAX3243CAI+T | MAX3243EEAI+ | MAX3243ECAI+ | MAX3243ECAI+G2X |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP |
| Driver Count | 3 drivers | 3 drivers | 3 drivers | 3 drivers | 3 drivers |
| Receiver Count | 5 receivers | 5 receivers | 5 receivers | 5 receivers | 5 receivers |
| Supply Voltage Range | 3.0V to 5.5V | 3.0V to 5.5V | 3.0V to 5.5V | 3.0V to 5.5V | 3.0V to 5.5V |
| Maximum Data Rate | 250kbps | 250kbps | 250kbps | 250kbps | 250kbps |
| Charge-Pump Architecture | Dual charge pump | Dual charge pump | Dual charge pump | Dual charge pump | Dual charge pump |
Diferenciadores clave
- Three-driver, five-receiver channel density (frente a MAX3232IPWR)
- Enhanced ESD protection for connector-side pins (frente a MAX3243CAI+T)
- Automatic low-power shutdown and wake-up (frente a MAX3243EEAI+)
- No external bipolar RS-232 supply required (frente a MAX3243ECAI+G2X)
Notas de diseño
Decouple the 3.0V-to-5.5V supply at the MAX3243ECAI+T power pins and connect the required charge-pump capacitors exactly as specified in the manufacturer datasheet. Keep these components close to their associated pins to limit supply ripple and charge-pump disturbance. Verify the capacitor voltage ratings, polarity, and effective capacitance tolerance over temperature; incorrect values can impair driver amplitude or wake-up behavior.
Separate charge-pump and driver-current paths from receiver inputs and controller-side logic. Use the manufacturer package outline and pin-description table when assigning PCB tracks, and keep the connector-side interface path compact. Avoid routing driver outputs beneath sensitive analog or low-level logic sections, and provide a continuous ground reference between the transceiver and the external RS-232 connector.
Do not assume that every MAX3243 ordering suffix is an exact production substitute without checking temperature grade, ESD rating, and reel or tube packaging. For MAX3243CAI+T, MAX3243EEAI+, MAX3243ECAI+, and MAX3243ECAI+G2X, compare the ordering tables and pin descriptions before substitution. Also confirm AutoShutdown polarity, receiver enable state, and charge-pump capacitor values to avoid communication failures after replacement.
Información de cumplimiento
The device is a commercial RS-232 interface IC. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the current manufacturer product or material declaration.