MAX3243ECAI+T - 3/5 RS-232 Transceiver, 15kV ESD | Analog Devices
MPN: MAX3243ECAI+T ✓ 啟用中MAX3243ECAI+T 概覽
An RS-232 transceiver is an interface IC that converts logic-level signals between a host controller and RS-232 differential line drivers and receivers. The MAX3243 belongs to the hierarchy of interface ICs, serial-interface transceivers, RS-232 communications devices, and semiconductors. It allows a modern low-voltage controller to communicate with legacy RS-232 equipment without requiring external ±12V power rails.
The MAX3243 integrates three RS-232 line drivers, five receivers, and a dual charge-pump circuit. Its 3.0V-to-5.5V single-supply operation supports both 3.3V and 5V systems. An internal charge pump generates the bipolar voltage required by RS-232 transmitters, while enhanced electrostatic-discharge protection improves resilience when cables are connected to external equipment. The E suffix identifies the enhanced ESD version, and the CAI suffix denotes the 28-pin SSOP configuration with a commercial temperature grade.
Automatic shutdown is a significant benefit in portable and low-power equipment. According to the manufacturer product page, the MAX3243 can reach a 1µA supply current when AutoShutdown is active and no valid signal appears at the receiver inputs. The device can wake automatically when receiver activity resumes, or shutdown can be controlled in software, allowing the interface to remain transparent to normal serial-port operation.
Typical uses include industrial serial adapters, point-of-sale equipment, data-acquisition systems, test instrumentation, and embedded controllers that must connect to RS-232 peripherals. Three drivers allow transmission on as many as three lines, while five receivers support monitoring of five incoming signals. The 250kbps capability exceeds the speed required by many legacy serial protocols and is useful for short-distance point-to-point links.
PCB design should keep charge-pump and high-voltage driver traces away from sensitive receiver and logic-ground paths. Place the required bypass capacitors close to their supply and ground pins, route connector-side signals according to the manufacturer pinout, and provide chassis grounding or surge-protection components where cables leave the enclosure. Confirm the receiver's active polarity and AutoShutdown timing in firmware before replacing a conventional RS-232 implementation.
This product record combines the manufacturer specifications, exact-package identification, lifecycle information, sourcing context, and drop-in alternatives with practical guidance for layout, power management, and signal-integrity review.
直接替換替代品,適用於 MAX3243ECAI+T — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MAX3243ECAI+T (相同外形與佔位) — 差異在於 Product Type, ESD Protection, Supply Voltage Range, Interface Standard, Package.
MAX3243CAI+T
✅ 直接替換📋 參考替代品(不在目錄中)
MAX3243EEAI+
✅ 直接替換聯絡詢價
查看資料表 →MAX3243ECAI+
✅ 直接替換聯絡詢價
查看資料表 →MAX3243ECAI+G2X
✅ 直接替換📋 參考替代品(不在目錄中)
MAX3243ECAI+T 規格
| Product Type | RS-232 line driver and receiver transceiver |
| Number of Drivers | 3 drivers |
| Number of Receivers | 5 receivers |
| Supply Voltage Range | 3.0V to 5.5V |
| Maximum Data Rate | 250kbps |
| ESD Protection | ±15kV HBM |
| AutoShutdown Supply Current | 1µA |
| Charge-Pump Circuit | Dual charge pump |
| Interface Standard | RS-232 / EIA/TIA-232 |
| Signaling Standard | V.28 / V.24 |
| 封裝 | 28-pin SSOP |
| Package Pin Count | 28 pins |
| 安裝類型 | Surface mount |
| Automotive Qualification | Not applicable |
MAX3243ECAI+T 28 pins 腳位配置指南
MAX3243ECAI+T(28 pins 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: MAX3243ECAI+T.
請參閱 資料表 以查看完整腳位配置。
典型應用
MAX3243ECAI+T 適用於 6 應用s: Industrial Serial Port Interface, Point-of-Sale Terminal Connectivity, Data Acquisition and Instrumentation, Embedded Equipment Controller, Network Equipment Serial Console, Portable Measurement and Control Device.
Industrial Serial Port Interface
The MAX3243ECAI+T fits industrial controllers that must communicate with RS-232 test equipment, programmable instruments, or legacy factory peripherals. Its three drivers support multiple outbound control signals, while five receivers can monitor acknowledgements, status lines, and sensor data. Operation from 3.0V to 5.5V removes external ±12V supplies, and the integrated dual charge pump simplifies the power architecture. The ±15kV HBM protection rating strengthens the connector-side interface when cables can be handled by operators. Automatic shutdown can also reduce standby consumption when the peripheral remains idle.
推薦
Point-of-Sale Terminal Connectivity
The MAX3243ECAI+T is appropriate for point-of-sale terminals, receipt printers, card-reader accessories, and service consoles that use RS-232 links. Three transmit channels can carry commands and data, while five receive channels provide enough monitoring points for printer status, transaction completion, and fault signaling. Its 3.3V-to-5V supply flexibility simplifies compatibility with embedded host processors. Because many peripheral ports remain idle between transactions, AutoShutdown and automatic wake-up can reduce system power without requiring the host to manage external RS-232 transceiver power rails.
推薦
Data Acquisition and Instrumentation
The MAX3243ECAI+T is suitable for data-acquisition units and laboratory instruments that expose a legacy RS-232 management port. The 250kbps maximum rate supports many short-distance control and status protocols, while five receivers allow the instrument to report multiple digital conditions to a host controller. The single 3.0V-to-5.5V supply is useful where a ±12V rail is undesirable, and the internal charge pump provides compliant RS-232 levels. Its enhanced ESD protection is valuable for bench equipment, although protective grounding and cable shielding should still follow the enclosure design.
推薦
Embedded Equipment Controller
The MAX3243ECAI+T fits embedded service equipment that must communicate with external RS-232 accessories while running from a 3.3V or 5V system rail. Three drivers permit command, configuration, and data channels, while five receivers provide flexible status monitoring. The device avoids the size and power cost of external charge-pump hardware. For equipment that spends substantial time disconnected from a cable, AutoShutdown can reduce supply demand to as little as 1µA, while receiver-triggered wake-up preserves transparent serial behavior. Firmware should allow sufficient settling time after a no-activity transition.
推薦
Network Equipment Serial Console
The MAX3243ECAI+T can provide a service or management console interface for routers, switches, and other network appliances that retain RS-232 diagnostics. Three transmit channels and five receive channels support console commands plus hardware status monitoring, and 250kbps is suitable for conventional terminal sessions. The 3.0V-to-5.5V operating range integrates readily with modern embedded processors. Automatic shutdown is advantageous for access ports that are not continuously connected, while the ±15kV HBM protection rating helps manage ESD introduced through service cables. Protect the enclosure entry and ground chassis appropriately for the installation environment.
推薦
Portable Measurement and Control Device
The MAX3243ECAI+T is well suited to portable measurement and control products that communicate with external sensors, fixtures, or service tools over RS-232. The single 3.0V-to-5.5V supply is compatible with common portable-system rails, while the dual charge pump avoids external high-voltage components. Three drivers and five receivers support richer control links than a basic one-driver, one-receiver interface. When no valid receiver activity is detected, AutoShutdown can lower consumption to 1µA, extending standby time. Wake-up latency and the cable’s ground reference must be checked against the operating scenario.
推薦
推薦產品摘要
工程參考資料,適用於 MAX3243ECAI+T — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MAX3243CAI+T | MAX3243EEAI+ | MAX3243ECAI+ | MAX3243ECAI+G2X |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP |
| Driver Count | 3 drivers | 3 drivers | 3 drivers | 3 drivers | 3 drivers |
| Receiver Count | 5 receivers | 5 receivers | 5 receivers | 5 receivers | 5 receivers |
| Supply Voltage Range | 3.0V to 5.5V | 3.0V to 5.5V | 3.0V to 5.5V | 3.0V to 5.5V | 3.0V to 5.5V |
| Maximum Data Rate | 250kbps | 250kbps | 250kbps | 250kbps | 250kbps |
| Charge-Pump Architecture | Dual charge pump | Dual charge pump | Dual charge pump | Dual charge pump | Dual charge pump |
主要差異化特點
- Three-driver, five-receiver channel density (對比MAX3232IPWR)
- Enhanced ESD protection for connector-side pins (對比MAX3243CAI+T)
- Automatic low-power shutdown and wake-up (對比MAX3243EEAI+)
- No external bipolar RS-232 supply required (對比MAX3243ECAI+G2X)
設計說明
Decouple the 3.0V-to-5.5V supply at the MAX3243ECAI+T power pins and connect the required charge-pump capacitors exactly as specified in the manufacturer datasheet. Keep these components close to their associated pins to limit supply ripple and charge-pump disturbance. Verify the capacitor voltage ratings, polarity, and effective capacitance tolerance over temperature; incorrect values can impair driver amplitude or wake-up behavior.
Separate charge-pump and driver-current paths from receiver inputs and controller-side logic. Use the manufacturer package outline and pin-description table when assigning PCB tracks, and keep the connector-side interface path compact. Avoid routing driver outputs beneath sensitive analog or low-level logic sections, and provide a continuous ground reference between the transceiver and the external RS-232 connector.
Do not assume that every MAX3243 ordering suffix is an exact production substitute without checking temperature grade, ESD rating, and reel or tube packaging. For MAX3243CAI+T, MAX3243EEAI+, MAX3243ECAI+, and MAX3243ECAI+G2X, compare the ordering tables and pin descriptions before substitution. Also confirm AutoShutdown polarity, receiver enable state, and charge-pump capacitor values to avoid communication failures after replacement.
合規資訊
The device is a commercial RS-232 interface IC. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the current manufacturer product or material declaration.