MAX3386ECDW - 3/2 RS-232 Transceiver, 250kbps | Texas Instruments
N.º de pieza: MAX3386ECDW ✗ Fin de vidaMAX3386ECDW Descripción general
An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and the bipolar voltage levels used by the RS-232 standard. It belongs to the communication transceiver family, which sits above line drivers and receivers in the interface hierarchy and ultimately supports serial data links in industrial, commercial, and embedded equipment.
Key electrical features include 500mV receiver hysteresis for improved noise immunity, 3V to 5.5V operation, and ±25kV ESD protection as identified for this device. The three-driver, two-receiver arrangement supports multiple outbound channels and two inbound channels within one package. Full-duplex operation allows simultaneous transmission and reception, while the split supply pins give the circuit designer independent control over the logic-side supply arrangement.
The MAX3386ECDW operates from 0°C to 70°C and is specified for surface-mount assembly in a 20-SOIC package measuring 0.295 inches, or 7.50mm, wide. Its 250kbps signaling rate is suitable for configuration ports, instrumentation, point-of-sale equipment, and legacy industrial control links. The integrated protection reduces the need for separate surge-protection components on exposed serial lines.
Typical applications include RS-232 ports for embedded controllers, test and measurement instruments, industrial diagnostic interfaces, and data acquisition systems. Because this part is obsolete, engineers should confirm availability, lifecycle status, and any manufacturer-approved migration path before releasing a new production design.
When laying out the board, keep the logic-side connections short and route the RS-232 lines away from clocks, switching regulators, and high-current power paths. Verify the external charge-pump capacitor values against the manufacturer datasheet and treat the RS-232 pins as external-facing signal nodes during EMC and ESD reviews.
This page consolidates device specifications, lifecycle information, pin-compatible alternatives, and design guidance for engineers evaluating the MAX3386ECDW against current RS-232 interface options.
Alternativas directas para MAX3386ECDW — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con MAX3386ECDW (mismo factor de forma y huella) — difiere en Package.
MAX3386EIDWR
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MAX3386EIDWRG4
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MAX3386ECDWR
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MAX3386EIDW
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →MAX3386ECDW Especificaciones
| Protocol | RS-232 |
| Transceiver Configuration | 3 drivers / 2 receivers |
| Duplex Mode | Full duplex |
| Maximum Data Rate | 250kbps |
| Supply Voltage Range | 3V to 5.5V |
| Receiver Hysteresis | 500mV |
| ESD Protection | ±25kV |
| Logic-Side Supply | Split supply pins |
| Rango de temperatura de funcionamiento | 0°C to 70°C |
| Temperature Grade | Commercial |
| Encapsulado | 20-SOIC (0.295", 7.50mm width) |
| Number of Terminals | 20 |
| Terminal Form | Gull wing |
| Package Shape | Rectangular |
| Tipo de montaje | Surface mount |
| Number of Drivers | 3 |
| Number of Receivers | 2 |
Guía de configuración de pines de MAX3386ECDW rectangular
Configuración de pines para MAX3386ECDW (encapsulado rectangular). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para MAX3386ECDW.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
MAX3386ECDW es adecuado para 6 aplicacións: Embedded Controller RS-232 Port, Industrial Diagnostic Interface, Test and Measurement Equipment, Data Acquisition System, Point-of-Sale Terminal Interface, Legacy Service and Configuration Port.
Embedded Controller RS-232 Port
The MAX3386ECDW fits a legacy serial port on an embedded controller because it operates from 3V to 5.5V and provides three drivers plus two receivers. A microcontroller can use one transmitter for command output and one receiver for response data, while the remaining channels support auxiliary links. Its 250kbps maximum rate is well above conventional RS-232 port rates, and 500mV receiver hysteresis improves tolerance to noise on external cables.
Recomendado
Industrial Diagnostic Interface
The MAX3386ECDW is suitable for industrial diagnostic links where service equipment connects to a controller through an RS-232 cable. The ±25kV-rated RS-232 pins help manage electrostatic discharge at the connector, while the three-driver and two-receiver arrangement allows multiple diagnostic channels in one device. The 0°C to 70°C commercial rating suits room-temperature equipment, but an industrial-temperature variant should be considered for uncontrolled environments.
Recomendado
Test and Measurement Equipment
In test and measurement instruments, the MAX3386ECDW can convert a controller's logic-level commands into RS-232 signals for a remote operator or peripheral. Its full-duplex architecture permits simultaneous command transmission and status reception, and its 250kbps capability is suitable for control and configuration traffic rather than high-rate bulk transfers. The split logic-side supply arrangement supports mixed-voltage designs when carefully referenced to the instrument ground.
Recomendado
Data Acquisition System
The MAX3386ECDW can interface legacy data-acquisition equipment through an RS-232 command and response port. Two receivers allow status or alarm information to be received while another channel drives a request, and the third driver can serve a second instrument bus. Its 500mV receiver hysteresis helps reject noise on bench-top and industrial cables, while the commercial 0°C to 70°C rating fits controlled laboratory environments.
Recomendado
Point-of-Sale Terminal Interface
The MAX3386ECDW suits point-of-sale and peripheral equipment that retains an RS-232 printer, scanner, or service connector. Three drivers support several outbound ports while two receivers can monitor device responses without changing the transmitter state. Its 3V minimum supply supports embedded controller platforms, and the 250kbps rate comfortably covers legacy peripheral traffic. Cable routing and connector-side protection remain important because these ports often extend outside the enclosure.
Recomendado
Legacy Service and Configuration Port
The MAX3386ECDW is useful in equipment requiring a service-only RS-232 configuration port alongside newer digital interfaces. A service controller can drive configuration commands while a separate receiver channel reads status logs or acknowledgement signals. The integrated three-driver and two-receiver arrangement reduces the number of discrete interface packages needed, and the 20-SOIC footprint simplifies legacy board-level servicing and mechanical replacement.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MAX3386ECDW — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | MAX3386EIDWR | MAX3386EIDWRG4 | MAX3386ECDWR |
|---|---|---|---|---|
| Package | 20-SOIC (0.295", 7.50mm width) | 20-SOIC - same | 20-SOIC - same | 20-SOIC - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Transceiver Configuration | 3 drivers / 2 receivers | 3 drivers / 2 receivers | 3 drivers / 2 receivers | 3 drivers / 2 receivers |
| Maximum Data Rate | 250kbps | 250kbps | 250kbps | 250kbps |
| Supply Voltage Range | 3V to 5.5V | 3V | 3V | 3V |
| Operating Temperature Range | 0°C to 70°C | Industrial-grade option | Industrial-grade option | 0°C to 70°C |
| Duplex Mode | Full duplex | Full duplex | Full duplex | Full duplex |
Diferenciadores clave
- Three transmitters and two receivers in one RS-232 package (frente a MAX3386EIDWR)
- Split logic-side supply for mixed-signal flexibility (frente a MAX3386ECDWR)
- Higher operating-temperature option within the same footprint (frente a MAX3386ECDW)
Notas de diseño
Keep logic-side traces short and separate the RS-232 driver outputs from sensitive receiver inputs. Place the manufacturer-specified charge-pump capacitors close to their associated pins with short, low-loop-area connections. Because the device includes split logic-side supply pins, define each rail at the IC and verify return-current paths so switching currents do not modulate the receiver reference.
Do not substitute a generic 20-pin SOIC transceiver solely by pin count. Confirm driver and receiver assignments, charge-pump connections, split-supply pins, and the exposed versus non-exposed package variant. The MAX3386EIDWR is documented as pin- and package-consistent with the target, while the MAX3386ECDWR and MAX3386EIDWRG4 are alternate ordering configurations of the same device family.
Treat every RS-232 connector pin as an external-facing port. Route cable-side traces away from clocks, power converters, and high-current loops, and consider connector-side surge or ESD protection when the cable can leave the enclosure. The internal ±25kV device protection rating does not replace enclosure-level EMC design or system immunity testing.
Decouple each supply pin according to the manufacturer layout guidance, with a short high-frequency bypass path to the intended ground reference. Check the 3V to 5.5V operating range against the logic-side system voltage, and avoid excessive loading on the split supply arrangement when the transceiver and controller do not share the same rail.
Información de cumplimiento
The device is listed as obsolete. The MAX3386EIDWRG4 ordering configuration may indicate a compliant finish, but RoHS, REACH, halogen-free, and conflict-minerals status were not explicitly established for the target part.