MAX3386ECDW - 3/2 RS-232 Transceiver, 250kbps | Texas Instruments
MPN: MAX3386ECDW ✗ انتهى عمره الإنتاجيMAX3386ECDW نظرة عامة
An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and the bipolar voltage levels used by the RS-232 standard. It belongs to the communication transceiver family, which sits above line drivers and receivers in the interface hierarchy and ultimately supports serial data links in industrial, commercial, and embedded equipment.
Key electrical features include 500mV receiver hysteresis for improved noise immunity, 3V to 5.5V operation, and ±25kV ESD protection as identified for this device. The three-driver, two-receiver arrangement supports multiple outbound channels and two inbound channels within one package. Full-duplex operation allows simultaneous transmission and reception, while the split supply pins give the circuit designer independent control over the logic-side supply arrangement.
The MAX3386ECDW operates from 0°C to 70°C and is specified for surface-mount assembly in a 20-SOIC package measuring 0.295 inches, or 7.50mm, wide. Its 250kbps signaling rate is suitable for configuration ports, instrumentation, point-of-sale equipment, and legacy industrial control links. The integrated protection reduces the need for separate surge-protection components on exposed serial lines.
Typical applications include RS-232 ports for embedded controllers, test and measurement instruments, industrial diagnostic interfaces, and data acquisition systems. Because this part is obsolete, engineers should confirm availability, lifecycle status, and any manufacturer-approved migration path before releasing a new production design.
When laying out the board, keep the logic-side connections short and route the RS-232 lines away from clocks, switching regulators, and high-current power paths. Verify the external charge-pump capacitor values against the manufacturer datasheet and treat the RS-232 pins as external-facing signal nodes during EMC and ESD reviews.
This page consolidates device specifications, lifecycle information, pin-compatible alternatives, and design guidance for engineers evaluating the MAX3386ECDW against current RS-232 interface options.
بدائل مباشرة لـ MAX3386ECDW — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع MAX3386ECDW (نفس عامل الشكل والبصمة) — يختلف في Package.
MAX3386EIDWR
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
MAX3386EIDWRG4
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
MAX3386ECDWR
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
MAX3386EIDW
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←MAX3386ECDW المواصفات
| Protocol | RS-232 |
| Transceiver Configuration | 3 drivers / 2 receivers |
| Duplex Mode | Full duplex |
| Maximum Data Rate | 250kbps |
| Supply Voltage Range | 3V to 5.5V |
| Receiver Hysteresis | 500mV |
| ESD Protection | ±25kV |
| Logic-Side Supply | Split supply pins |
| نطاق درجة حرارة التشغيل | 0°C to 70°C |
| Temperature Grade | Commercial |
| العلبة | 20-SOIC (0.295", 7.50mm width) |
| Number of Terminals | 20 |
| Terminal Form | Gull wing |
| Package Shape | Rectangular |
| نوع التركيب | Surface mount |
| Number of Drivers | 3 |
| Number of Receivers | 2 |
دليل تكوين أطراف MAX3386ECDW rectangular
تكوين الأطراف لـ MAX3386ECDW (حزمة rectangular). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ MAX3386ECDW.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
MAX3386ECDW مناسب لـ 6 التطبيقs: Embedded Controller RS-232 Port, Industrial Diagnostic Interface, Test and Measurement Equipment, Data Acquisition System, Point-of-Sale Terminal Interface, Legacy Service and Configuration Port.
Embedded Controller RS-232 Port
The MAX3386ECDW fits a legacy serial port on an embedded controller because it operates from 3V to 5.5V and provides three drivers plus two receivers. A microcontroller can use one transmitter for command output and one receiver for response data, while the remaining channels support auxiliary links. Its 250kbps maximum rate is well above conventional RS-232 port rates, and 500mV receiver hysteresis improves tolerance to noise on external cables.
موصى به
Industrial Diagnostic Interface
The MAX3386ECDW is suitable for industrial diagnostic links where service equipment connects to a controller through an RS-232 cable. The ±25kV-rated RS-232 pins help manage electrostatic discharge at the connector, while the three-driver and two-receiver arrangement allows multiple diagnostic channels in one device. The 0°C to 70°C commercial rating suits room-temperature equipment, but an industrial-temperature variant should be considered for uncontrolled environments.
موصى به
Test and Measurement Equipment
In test and measurement instruments, the MAX3386ECDW can convert a controller's logic-level commands into RS-232 signals for a remote operator or peripheral. Its full-duplex architecture permits simultaneous command transmission and status reception, and its 250kbps capability is suitable for control and configuration traffic rather than high-rate bulk transfers. The split logic-side supply arrangement supports mixed-voltage designs when carefully referenced to the instrument ground.
موصى به
Data Acquisition System
The MAX3386ECDW can interface legacy data-acquisition equipment through an RS-232 command and response port. Two receivers allow status or alarm information to be received while another channel drives a request, and the third driver can serve a second instrument bus. Its 500mV receiver hysteresis helps reject noise on bench-top and industrial cables, while the commercial 0°C to 70°C rating fits controlled laboratory environments.
موصى به
Point-of-Sale Terminal Interface
The MAX3386ECDW suits point-of-sale and peripheral equipment that retains an RS-232 printer, scanner, or service connector. Three drivers support several outbound ports while two receivers can monitor device responses without changing the transmitter state. Its 3V minimum supply supports embedded controller platforms, and the 250kbps rate comfortably covers legacy peripheral traffic. Cable routing and connector-side protection remain important because these ports often extend outside the enclosure.
موصى به
Legacy Service and Configuration Port
The MAX3386ECDW is useful in equipment requiring a service-only RS-232 configuration port alongside newer digital interfaces. A service controller can drive configuration commands while a separate receiver channel reads status logs or acknowledgement signals. The integrated three-driver and two-receiver arrangement reduces the number of discrete interface packages needed, and the 20-SOIC footprint simplifies legacy board-level servicing and mechanical replacement.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ MAX3386ECDW — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | MAX3386EIDWR | MAX3386EIDWRG4 | MAX3386ECDWR |
|---|---|---|---|---|
| Package | 20-SOIC (0.295", 7.50mm width) | 20-SOIC - same | 20-SOIC - same | 20-SOIC - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Transceiver Configuration | 3 drivers / 2 receivers | 3 drivers / 2 receivers | 3 drivers / 2 receivers | 3 drivers / 2 receivers |
| Maximum Data Rate | 250kbps | 250kbps | 250kbps | 250kbps |
| Supply Voltage Range | 3V to 5.5V | 3V | 3V | 3V |
| Operating Temperature Range | 0°C to 70°C | Industrial-grade option | Industrial-grade option | 0°C to 70°C |
| Duplex Mode | Full duplex | Full duplex | Full duplex | Full duplex |
أبرز الفروقات
- Three transmitters and two receivers in one RS-232 package (مقابلMAX3386EIDWR)
- Split logic-side supply for mixed-signal flexibility (مقابلMAX3386ECDWR)
- Higher operating-temperature option within the same footprint (مقابلMAX3386ECDW)
ملاحظات التصميم
Keep logic-side traces short and separate the RS-232 driver outputs from sensitive receiver inputs. Place the manufacturer-specified charge-pump capacitors close to their associated pins with short, low-loop-area connections. Because the device includes split logic-side supply pins, define each rail at the IC and verify return-current paths so switching currents do not modulate the receiver reference.
Do not substitute a generic 20-pin SOIC transceiver solely by pin count. Confirm driver and receiver assignments, charge-pump connections, split-supply pins, and the exposed versus non-exposed package variant. The MAX3386EIDWR is documented as pin- and package-consistent with the target, while the MAX3386ECDWR and MAX3386EIDWRG4 are alternate ordering configurations of the same device family.
Treat every RS-232 connector pin as an external-facing port. Route cable-side traces away from clocks, power converters, and high-current loops, and consider connector-side surge or ESD protection when the cable can leave the enclosure. The internal ±25kV device protection rating does not replace enclosure-level EMC design or system immunity testing.
Decouple each supply pin according to the manufacturer layout guidance, with a short high-frequency bypass path to the intended ground reference. Check the 3V to 5.5V operating range against the logic-side system voltage, and avoid excessive loading on the split supply arrangement when the transceiver and controller do not share the same rail.
معلومات الامتثال
The device is listed as obsolete. The MAX3386EIDWRG4 ordering configuration may indicate a compliant finish, but RoHS, REACH, halogen-free, and conflict-minerals status were not explicitly established for the target part.