MC33394DH - 3A Multi-Output Power Supply | NXP Semiconductors
N.º de pieza: MC33394DH ✓ ActivoMC33394DH Descripción general
A multi-output power supply IC combines switching conversion, low-dropout regulation, supervisory functions, and communication circuitry into one device for embedded automotive electronics. The switching stage reduces the difference between the battery input and regulated rail, while the integrated LDO outputs provide lower-noise voltage rails for processors, sensors, memory, and communication interfaces. This integration reduces the number of discrete regulators and supports efficient power sequencing in vehicle electronic control units.
The MC33394DH provides VDDH at 5.0 V and 400 mA, VDD3_3 at 3.3 V and 120 mA, and VDDL at 2.6 V with user scaling between 3.3 V and 1.25 V at up to 400 mA typically. The VDDL output uses an external NPN pass transistor. A scalable keep-alive regulator, VKAM, supplies approximately 50 mA. The switching regulator operates in buck mode or boost mode and includes an internal 3.0 A current limit.
The integrated high-speed CAN transceiver makes the IC appropriate for automotive and industrial applications requiring both local power management and network connectivity. A typical architecture places the MC33394DH near the vehicle power connector, derives several regulated rails for an MCU and its peripherals, and uses the CAN interface to communicate with sensors, actuators, or diagnostic equipment. The external NPN pass transistor allows the VDDL regulator to scale its output while keeping the high-current switching path outside the IC.
Designers should pay close attention to the 4 V minimum operating input, the 26.5 V maximum operating input, regulator current ratings, external transistor selection, exposed-pad thermal management, and the required external compensation and storage components. The manufacturer datasheet should be used for the complete pin assignment, recommended application circuit, electrical limits, timing information, and PCB layout guidance.
This page combines the core electrical capabilities, application context, and design considerations for engineers evaluating the MC33394DH in an embedded automotive power architecture. It also identifies the exact package, supported power rails, and the design parameters that should be checked before PCB release.
Alternativas directas para MC33394DH — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
No hay alternativas directas disponibles para este producto.
Solicitar alternativasMC33394DH Valores máximos y características eléctricas
| Product Type | Multi-output switch-mode power supply with integrated linear regulators and CAN transceiver |
| Manufacturer | NXP Semiconductors |
| Switching Regulator Current Limit | 3.0 A |
| Switching Regulator Modes | Buck mode or boost mode |
| Rango de tensión de entrada | 4 V to 26.5 V |
| VDDH Output Voltage | 5.0 V |
| VDDH Output Current | 400 mA |
| VDD3_3 Output Voltage | 3.3 V |
| VDD3_3 Output Current | 120 mA |
| VDDL Output Voltage | 2.6 V, user scalable between 3.3 V and 1.25 V |
| VDDL Output Current | 400 mA typically |
| VDDL Pass Device | External NPN pass transistor |
| VKAM Output Current | 50 mA |
| CAN Interface | Integrated high-speed CAN transceiver |
| Encapsulado | 44-HSOP with exposed pad |
| Tipo de montaje | Surface mount |
| Automotive Processor Support | Motorola MPC55x and MPC56x microprocessors |
Guía de configuración de pines de MC33394DH 44-hsop with exposed pad
Configuración de pines para MC33394DH (encapsulado 44-hsop with exposed pad). Este dispositivo de potencia presenta terminales de puerta, drenador y fuente. Para encapsulados no polarizados, consulte la hoja de datos del fabricante para conocer la orientación exacta del pin 1 y los detalles del footprint. Las aplicaciones habituales incluyen el diseño de fuentes de alimentación, el accionamiento de motores y la conmutación de cargas.
No hay datos detallados de patillaje disponibles para MC33394DH.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
MC33394DH es adecuado para 6 aplicacións: Automotive Electronic Control Unit Power, MPC55x Microprocessor Control Platform, MPC56x Automotive Processor Platform, CAN-Connected Industrial Sensor Node, Body and Chassis Control Module, Industrial Motor and Actuator Controller.
Automotive Electronic Control Unit Power
The MC33394DH fits automotive electronic control units that need several power rails and CAN connectivity from one device. Its switching regulator supports buck or boost operation with an internal 3.0 A current limit, while VDDH supplies 5.0 V at 400 mA and VDD3_3 supplies 3.3 V at 120 mA. The scalable VDDL rail supports MCU core and peripheral power from 1.25 V to 3.3 V, with an external NPN pass transistor providing the high-current path. In a vehicle network node, the integrated high-speed CAN transceiver can link the controller to sensors and actuators. Designers should follow the NXP application circuit for compensation, storage, pass-transistor selection, and exposed-pad thermal layout.
Recomendado
MPC55x Microprocessor Control Platform
The MC33394DH is suited to MPC55x-based control platforms requiring dedicated processor and peripheral rails. Its 5.0 V VDDH output supports up to 400 mA, the 3.3 V VDD3_3 rail supports up to 120 mA, and the scalable VDDL output can be adjusted between 1.25 V and 3.3 V for processor-related loads. This integration allows a compact ECU power architecture without implementing every regulator as a separate component. The external NPN pass transistor associated with VDDL must be sized for the intended output current and thermal conditions. PCB placement should minimize loop area in the switching stage and provide substantial copper beneath the 44-HSOP exposed pad.
Recomendado
MPC56x Automotive Processor Platform
The MC33394DH supports MPC56x embedded platforms by combining a wide 4 V to 26.5 V supply input with multiple regulated outputs. VDDH at 5.0 V and 400 mA can serve general 5 V circuitry, VDD3_3 at 3.3 V and 120 mA can support compatible peripherals, and VDDL can be scaled for lower-voltage processor requirements. The high-speed CAN transceiver provides a direct network interface alongside the power-management functions. This arrangement is useful when component count and ECU board area are important. The complete reference design should still be reviewed for startup behavior, current sharing, inductor selection, and thermal performance under worst-case vehicle conditions.
Recomendado
CAN-Connected Industrial Sensor Node
The MC33394DH can support industrial sensor nodes that require regulated logic power and a high-speed CAN connection. The buck-or-boost switching stage accommodates different source conditions, while the internal 3.0 A current limit protects the converter during overload conditions. VDDH at 5.0 V can power compatible sensors, VDD3_3 at 3.3 V can support digital interfaces, and the VKAM keep-alive rail at approximately 50 mA can support retention or low-power functions where applicable. The integrated CAN transceiver reduces the number of external interface components. Industrial implementations should verify the complete electrical limits, EMC requirements, and environmental qualification in the NXP datasheet before deployment.
Recomendado
Body and Chassis Control Module
The MC33394DH is appropriate for body and chassis modules that coordinate switches, lamps, sensors, and actuators through a CAN network. Its 4 V to 26.5 V input range accommodates automotive electrical environments, while VDDH, VDD3_3, and scalable VDDL outputs support mixed logic voltage domains. The integrated CAN transceiver enables network communication without requiring a separate physical-layer device. The 44-HSOP exposed pad and high-current switching section require careful layout to control thermal rise and electromagnetic interference. Use the NXP reference information to select the external NPN pass transistor, inductor, compensation network, and input and output capacitors around the device.
Recomendado
Industrial Motor and Actuator Controller
The MC33394DH can serve as the local power manager in an industrial motor or actuator controller that also uses CAN for command and diagnostic traffic. The switching regulator supplies pre-regulated energy for the VDDH, VDD3_3, and VDDL outputs, while its 3.0 A current limit provides a defined overload threshold. The VDDL rail supports user-scalable voltages down to 1.25 V, which is useful for programmable control logic and sensor interfaces. Because actuator systems may experience large transients and thermal variation, the input network, pass transistor, and exposed-pad copper must be validated for the actual load profile. The manufacturer application circuit remains the starting point for component selection and layout.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MC33394DH — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Notas de diseño
Route the switching-regulator current path and the MC33394DH exposed pad according to the NXP datasheet land pattern. Provide the recommended exposed-pad copper and thermal-via structure, then calculate worst-case junction temperature from regulator dissipation, ambient temperature, and the realized board thermal resistance. Do not estimate thermal performance from package area alone because the external NPN pass transistor and surrounding power components also dissipate energy.
Place the input capacitor, switching inductor, compensation elements, output capacitors, and external NPN pass transistor close to their associated IC pins. Keep the high-current switching loop compact to reduce EMI and voltage ringing. Connect the 44-HSOP exposed pad according to the manufacturer pin-description table and package drawing, and route sensitive CAN and low-current signal paths away from the switching node.
Validate each rail independently for startup sequencing, minimum load behavior, transient response, and the stated current limits: 400 mA for VDDH, 120 mA for VDD3_3, and 400 mA typically for VDDL. The internal 3.0 A current limit belongs to the switching regulator and should not be treated as a continuous-output rating for every downstream rail. Select the external NPN pass transistor using the VDDL requirements from the datasheet.
Información de cumplimiento
The available product information identifies automotive and industrial applications but does not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Confirm these declarations against the manufacturer product page and current quality documentation before procurement.