MCP3304T-CI/SL - 13-Bit 4-Channel ADC | Microchip
N.º de pieza: MCP3304T-CI/SL ✓ ActivoMCP3304T-CI/SL Descripción general
An ADC converts an analog voltage into a numeric value for measurement, control, logging, or signal processing. The MCP3304 belongs to the ADC and DAC hierarchy within integrated circuits, combining a sample-and-hold input stage, successive-approximation conversion, and serial data output in one device. Its differential inputs are particularly useful when the measured signal requires rejection of common-mode voltage or rejection of noise referenced to an analog ground.
The device provides 13-bit resolution, four differential or eight single-ended input choices, and a 100 kHz maximum sampling capability. Its SPI interface supports communication with microcontrollers and other embedded processors. Low-power operation makes the converter suitable for battery-powered instrumentation, remote data acquisition, industrial control, and portable measurement systems where the complete system must balance conversion speed, energy use, and board area.
The MCP3304 architecture samples the selected input and performs successive-approximation conversion, producing one code for each conversion result. The digital result is transferred through the serial interface, reducing the number of signal connections compared with a parallel-output converter. The 16-pin SOIC provides a compact surface-mount footprint and is easier to inspect or service than a very fine-pitch package in low- to moderate-volume industrial equipment.
Typical uses include multichannel analog sensing, process monitoring, laboratory measurement, battery-powered data loggers, and embedded control systems. Differential sensing is appropriate when sensors produce a voltage centered around a biased common-mode level, while single-ended operation can simplify systems with multiple sensors referenced to ground. The 100 kHz conversion capability provides headroom for rapidly changing or multiplexed analog signals.
Design the analog front end around the input voltage range, source impedance, acquisition time, and reference stability. Keep analog traces short, use a low-noise reference arrangement, and place input and reference decoupling capacitors close to the device. Treat the SPI clock and digital signals as potential noise sources by keeping them away from sensitive input and reference nodes.
This page combines the manufacturer product information with package, application, replacement, and design guidance. It also distinguishes exact drop-in choices from functional alternatives that would require different pinouts, packages, or interface assumptions, helping engineers select a converter without changing the PCB unnecessarily.
Alternativas directas para MCP3304T-CI/SL — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con MCP3304T-CI/SL (mismo factor de forma y huella) — difiere en Input Configuration, Input Type, Package.
MCP3304-BI/SL
✅ Sustitución directaConsulte el precio
Ver hoja de datos →MCP3304T-AI/SL
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
MCP3304T-I/SL
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
MCP3304T-CI/SL Valores máximos y características eléctricas
| Resolución | 13 bit |
| Input Configuration | 4 differential inputs or 8 single-ended inputs |
| Conversion Architecture | 1 successive-approximation converter |
| Maximum Conversion Rate | 100 kHz |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Interfaz | SPI serial interface |
| Input Type | Differential and single-ended analog inputs |
| Encapsulado | 16-pin SOIC |
| Tipo de montaje | Surface mount |
Guía de configuración de pines de MCP3304T-CI/SL 16-pin soic
Configuración de pines para MCP3304T-CI/SL (encapsulado 16-pin soic). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para MCP3304T-CI/SL.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
MCP3304T-CI/SL es adecuado para 6 aplicacións: Industrial Process Monitoring, Battery-Powered Remote Data Acquisition, Laboratory Measurement Equipment, Precision Current and Voltage Sensing, Embedded Environmental Sensing, Automotive and Mobile Analog Sensing.
Industrial Process Monitoring
The MCP3304T-CI/SL fits industrial process monitoring because it combines four differential inputs with 13-bit resolution and a 100 kHz maximum conversion rate. Multiple sensors can share the converter through its eight single-ended inputs, while differential channels suit bridge outputs and shunts that carry a common-mode voltage. The SPI interface transfers results to a controller such as an MSP430-family microcontroller. Design the front end so sensor outputs remain inside the converter input range, and keep the analog reference and input traces away from SPI clock signals.
Recomendado
Battery-Powered Remote Data Acquisition
The MCP3304T-CI/SL is appropriate for battery-powered remote data acquisition because the Microchip MCP3304 family emphasizes low-power operation, compactness, and an industry-standard SPI interface. Four differential inputs can monitor low-level sensor outputs while their common-mode reference helps reject noise coupled equally to both wires. At a 100 kHz maximum rate, the device can sample several channels sequentially when the application requires faster updates. Battery life depends on how often the MCU wakes, the number of conversions performed, sensor loading, and reference-circuit consumption, so include those loads in the system budget.
Recomendado
Laboratory Measurement Equipment
The MCP3304T-CI/SL can serve as the measurement front end in laboratory instrumentation that needs more than a coarse sensor reading but not a high-speed waveform converter. Four differential channels allow several precision sensors to share a common measurement system, while the 13-bit result provides 8192 possible digital code levels across the selected analog range. The SPI output is practical for a microcontroller or embedded controller, and the 16-pin SOIC remains inspectable on laboratory-oriented boards. Accuracy ultimately depends on reference stability, front-end noise, grounding, calibration, and the selected input range rather than resolution alone.
Recomendado
Precision Current and Voltage Sensing
The MCP3304T-CI/SL is well suited to precision shunt and sensor measurements because its four differential inputs measure a voltage across two nodes rather than referencing every sensor directly to ground. A shunt amplifier can produce a small differential voltage proportional to current, while the ADC reports a 13-bit digital code. The four-channel configuration supports simultaneous measurement of several loads or rails without sharing an input node. Keep high-current paths separated from sensitive analog traces, use Kelvin routing where appropriate, and verify the differential input limits and reference voltage in the manufacturer datasheet.
Recomendado
Embedded Environmental Sensing
The MCP3304T-CI/SL supports embedded environmental sensing systems that combine temperature, pressure, humidity, or gas sensors with low-level analog outputs. Its eight single-ended inputs can serve several ground-referenced sensors, while four differential inputs support sensors that operate around a biased common-mode voltage. The 13-bit resolution and 100 kHz conversion capability cover many slow environmental measurements while leaving bandwidth for periodic sampling. A microcontroller can configure channels over SPI and apply calibration, offset correction, and filtering. Place sensor grounds and converter references using a quiet analog return path to prevent digital switching noise from influencing low-level readings.
Recomendado
Automotive and Mobile Analog Sensing
The MCP3304T-CI/SL architecture can support mobile analog-sensing subsystems where several low-voltage sensor channels must be digitized through a compact serial interface. Four differential inputs reduce sensitivity to common-mode disturbances when sensors are referenced to a biased return path, and the 16-pin SOIC supports straightforward surface-mount assembly. The SPI link allows an embedded controller to sample, filter, and transmit measurements. For automotive production, select the ordering grade whose qualification and temperature requirements match the vehicle environment; the automotive ordering variant should be reviewed when AEC-Q100 evidence is required.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MCP3304T-CI/SL — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | MCP3304-BI/SL | MCP3304T-AI/SL | MCP3304T-I/SL |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Resolution | 13 bit | 13 bit | 13 bit | 13 bit |
| Input Configuration | 4 differential inputs or 8 single-ended inputs | 4 differential inputs or 8 single-ended inputs | 4 differential inputs or 8 single-ended inputs | 4 differential inputs or 8 single-ended inputs |
| Conversion Architecture | 1 SAR converter | 1 SAR converter | 1 SAR converter | 1 SAR converter |
| Maximum Conversion Rate | 100 kHz | 100 kHz | 100 kHz | 100 kHz |
| Supply Voltage Range | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| Interface | SPI | SPI | SPI | SPI |
| Ordering Grade | C industrial grade | B grade | A automotive grade | I grade |
| Special Features | Differential and single-ended input operation | Differential and single-ended input operation | Differential and single-ended input operation | Differential and single-ended input operation |
Diferenciadores clave
- Maintains the established MCP3304 conversion and interface performance (frente a MCP3304-BI/SL)
- Offers an automotive-qualified family option without changing the electrical architecture (frente a MCP3304T-AI/SL)
- Combines multiple analog inputs with a compact serial interface (frente a MCP3304T-I/SL)
Notas de diseño
Place input, reference, and supply decoupling components directly beside their associated pins. Keep analog input traces short and continuous, avoid routing them beneath digital clocks, and use a quiet analog ground strategy. For differential measurements, route the positive and negative signals as a closely matched pair to minimize conversion of external noise into a differential error.
Treat the SPI clock as the principal digital switching source. Keep clock routing away from analog inputs and the reference node, provide a continuous return path, and avoid sharing narrow neck points between analog and digital return currents. If the sensor source impedance is high, compare its charging requirement with the converter acquisition time and add a suitable charge-injection or buffer circuit instead of assuming the sample-and-hold capacitor will settle fully.
The MCP3304T-CI/SL operates from 4.5 V to 5.5 V, so the 5 V rail must remain within that range during transients. Use local bulk and high-frequency bypass capacitance, and provide clean return-current paths from the supply pins. The reference voltage directly scales the measurable input range and conversion accuracy, so isolate it from digital loading and evaluate its noise, startup behavior, and temperature drift rather than treating it as a fixed ideal source.
Do not substitute an ADC solely because it also has a 13-bit rating and an SPI interface. A genuine PCB replacement must preserve the 16-pin SOIC pinout, SPI mode and timing, input ranges, reference arrangement, and conversion behavior. Also verify that the replacement ordering grade provides the required operating temperature and qualification. A different package or pin map is a redesign, not a drop-in substitution.
Información de cumplimiento
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements appear in the manufacturer page excerpts. The automotive ordering variant may address vehicle-grade requirements, but qualification status must be confirmed from the relevant manufacturer documentation.