OPA347PA - 350kHz Micropower RRIO Op Amp | Texas Instruments
N.º de pieza: OPA347PA ✓ ActivoOPA347PA Descripción general
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs while using negative feedback to set a stable closed-loop gain. The OPA347 belongs to the hierarchy of operational amplifier, voltage-feedback amplifier, analog amplifier, and semiconductor. Rail-to-rail input and output, commonly abbreviated RRIO, allow the amplifier to operate near the supply rails without requiring a reduced common-mode or output-voltage range.
The principal features of the OPA347 are its 5.5 V maximum supply voltage, 350 kHz gain-bandwidth product, and low quiescent current. According to the manufacturer datasheet, the input range extends 200 mV beyond the supply rails, while the output range reaches within 5 mV of the rails. These characteristics support sensor interfaces, low-current signal conditioning, portable instrumentation, and analog measurement circuits.
The OPA347 uses a low-power amplifier architecture optimized for speed-to-power performance rather than the bandwidth of a high-speed operational amplifier. Its 350 kHz bandwidth is adequate for low-frequency sensor signals and general-purpose analog conditioning. Input operation beyond the nominal rails improves usable signal range in low-voltage systems, although common-mode, output-swing, and supply-voltage limits must still be respected during design.
Typical uses include battery-powered sensor conditioning, portable biomedical instrumentation, low-power data acquisition, current sensing, and buffering. It is particularly appropriate where the signal bandwidth is well below 350 kHz and the 20 uA nominal quiescent current is valuable for extending battery life. The device can also serve as a general-purpose amplifier or voltage follower when low-noise settling and low standby consumption are priorities.
Designers should verify the complete common-mode and output-swing curves at the intended supply voltage and load current. Decoupling capacitors should be placed close to the supply pins, input bias currents should remain below the source impedance, and the feedback network should be evaluated for output-capacitance stability. The PDIP package is suited to prototypes, educational assemblies, and through-hole production runs where a surface-mount package is unnecessary.
This page organizes the OPA347PA specifications, package details, practical design guidance, verified-source references, and same-family replacement information into one engineering-focused reference. It also identifies which operating parameters require confirmation in the manufacturer datasheet rather than presenting unsupported values as fixed design limits.
Alternativas directas para OPA347PA — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
OPA347P
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
OPA347PA Valores máximos y características eléctricas
| Amplifier Type | Single operational amplifier |
| Maximum Supply Voltage | 5.5 V |
| Gain-Bandwidth Product | 350 kHz |
| Nominal Quiescent Current | 20 uA |
| Maximum Quiescent Current | 34 uA per channel |
| Input Rail-to-Rail Operation | Yes; input range extends 200 mV beyond the rails |
| Output Rail-to-Rail Operation | Yes; output range is within 5 mV of the rails |
| Output Voltage Swing | Within 5 mV of the supply rails |
| Rango de temperatura de funcionamiento | -55 C to +125 C |
| Encapsulado | 8-pin PDIP |
| Recuento de pines | 8 pins |
| Tipo de montaje | Through-hole DIP |
| Circuit Count | 1 circuit |
Configuración de pines de OPA347PA
| Pin 1 | NC — Not connected |
| Pin 2 | IN- — Inverting input |
| Pin 3 | IN+ — Non-inverting input |
| Pin 4 | V- — Negative supply voltage |
| Pin 5 | NC — Not connected |
| Pin 6 | OUT — Output voltage |
| Pin 7 | V+ — Positive supply voltage |
| Pin 8 | NC — Not connected |
Aplicaciones típicas
OPA347PA es adecuado para 6 aplicacións: Battery-Powered Sensor Conditioning, Portable Medical Instrumentation, Low-Power Data Acquisition, Current and Voltage Sensing, General-Purpose Low-Power Buffering, Industrial Control and Monitoring.
Battery-Powered Sensor Conditioning
OPA347PA is well suited to conditioning slow sensor outputs in battery-powered equipment because its nominal quiescent current is 20 uA and its maximum value is 34 uA per channel. Place the amplifier near the sensor interface so long unamplified traces do not add avoidable loading or noise pickup. Rail-to-rail input operation, with the input range extending 200 mV beyond the rails, helps preserve signal headroom in compact low-voltage systems. The 350 kHz bandwidth is more than adequate for temperature, pressure, and slow-motion sensors, while stable feedback resistors keep the micropower stage responsive.
Recomendado
Portable Medical Instrumentation
OPA347PA can serve as a low-power gain stage or buffer in portable medical instrumentation where a small signal must be conditioned before an ADC. Its 20 uA nominal quiescent current reduces continuous battery drain, while the 350 kHz bandwidth handles many bio-sensor and diagnostic front-end signals. The rail-to-rail input and output capability supports operation from low supply voltages without immediately clipping at the rails. Gain, input bias current, offset, noise, and isolation requirements must still be reviewed against the specific sensor and safety architecture.
Recomendado
Low-Power Data Acquisition
OPA347PA is useful as an input amplifier or unity-gain buffer in a compact data-acquisition channel operating from a low-voltage supply. Its 350 kHz gain-bandwidth product provides ample closed-loop bandwidth for many multiplexed slow inputs, while the 20 uA nominal quiescent current limits the penalty from keeping one amplifier continuously powered. Place the device close to the ADC input and use short, guarded routing to minimize pickup. Decoupling near the supply pins and properly scaled feedback resistors help maintain predictable operation across temperature.
Recomendado
Current and Voltage Sensing
OPA347PA can amplify the small differential voltage produced by a current-sense element or precision resistive divider. Its rail-to-rail input behavior is useful when the sensed signal approaches a supply rail, and the input range extending 200 mV beyond the rails provides additional margin in low-voltage systems. The 350 kHz bandwidth supports bandwidths common to slow current measurements. Designers should verify source impedance, input bias-current error, common-mode limits, and output swing at the maximum load current before finalizing the gain network.
Recomendado
General-Purpose Low-Power Buffering
OPA347PA works as a voltage follower or general-purpose buffer when a high-impedance source must drive a moderate downstream load without adding excessive supply demand. Its 20 uA nominal quiescent current benefits battery-operated equipment, and the output stage can operate within 5 mV of the rails under the conditions stated by the manufacturer datasheet. Use a unity-gain configuration when isolation and impedance conversion are the main goals. Confirm stability with the source capacitance, load capacitance, and external feedback network used in the final circuit.
Recomendado
Industrial Control and Monitoring
OPA347PA is appropriate for low-frequency industrial monitoring circuits that process sensor outputs from a low-voltage control system. The rail-to-rail input range allows the amplifier to handle signals near the supply limits, while 350 kHz bandwidth covers many process-control and diagnostic waveforms. Its low quiescent current benefits distributed monitoring modules with limited thermal budgets. Industrial qualification requirements should be checked separately from the stated operating-temperature range, and protection networks should handle transients that exceed the amplifier's 5.5 V maximum supply voltage.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para OPA347PA — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | OPA347P |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-pin PDIP | 8-pin PDIP |
| Maximum Supply Voltage | 5.5 V | 5.5 V |
| Gain-Bandwidth Product | 350 kHz | 350 kHz |
| Nominal Quiescent Current | 20 uA | 20 uA |
| Maximum Quiescent Current | 34 uA per channel | 34 uA per channel |
| Input Common-Mode Range | Extends 200 mV beyond the supply rails | Extends 200 mV beyond the supply rails |
| Output Swing | Within 5 mV of the supply rails | Within 5 mV of the supply rails |
| Circuit Count | 1 circuit | 1 circuit |
| Operating Temperature Range | -55 C to +125 C | -55 C to +125 C |
Diferenciadores clave
- Low micropower operation supports battery-focused designs (frente a OPA2347EA/3KG4)
- Through-hole package supports direct DIP-8 assembly (frente a OPA2347EA/3KG4)
- Rail-to-rail operation improves low-voltage signal utilization (frente a OPA347P)
Notas de diseño
Estimated: with a 3.3 V supply, 5 uA load, and 20 uA quiescent current, the nominal supply-current contribution is approximately 25 uA. This is an arithmetic estimate using the stated values rather than a datasheet maximum. Verify the maximum supply current over temperature and account for output-current demand, charger leakage, and regulator quiescent current when sizing a battery.
Place the supply-bypass capacitor directly between pins 7 and 4, with a short and low-inductance ground return. Route both input traces away from the output and supply paths, particularly when the source impedance is high. If the amplifier drives a capacitive load, add the isolation resistance and load range recommended in the manufacturer datasheet rather than relying on excessive feedback capacitance.
Do not assume that a rail-to-rail input amplifier can accept signals indefinitely beyond its supply pins. The stated 200 mV over-rail input capability has device-specific limits, and the exact common-mode range must be checked at the operating supply voltage. Also avoid using the maximum 350 kHz gain-bandwidth figure as a guaranteed small-signal bandwidth for every closed-loop gain and load.
Keep source impedances low enough that input-bias-current error remains small relative to the sensor signal. Use matched feedback resistors to reduce offset generated by bias currents, and avoid extremely high closed-loop gains with a single amplifier when noise, offset, and settling requirements dominate. For fast edge or step responses, evaluate closed-loop settling separately because the 350 kHz gain-bandwidth product alone does not specify settling accuracy.
Información de cumplimiento
No explicit compliance declarations were present in the manufacturer and distributor product information. The operating-temperature comparison identifies the OPA347PA as rated for -55 C to +125 C, but temperature ratings alone do not establish AEC-Q100 qualification.