OPA743PA - 12V, 7MHz CMOS RRIO Op Amp | Texas Instruments
N.º de pieza: OPA743PA ✓ ActivoOPA743PA Descripción general
An operational amplifier is a voltage-gain component that compares its inverting and non-inverting inputs and drives its output according to the difference between them. Within the broader semiconductor hierarchy, the OPA743PA belongs to the CMOS operational-amplifier family, where it provides signal amplification, buffering, filtering, and level conversion for analog and mixed-signal systems. Its rail-to-rail input and output characteristics make it useful when signals approach the supply rails.
The device combines a 7 MHz gain-bandwidth product with a 10 V/µs slew rate, allowing it to process higher-frequency signals without requiring a bipolar operational amplifier. Typical quiescent current is 1.1 mA, helping limit power consumption in battery-powered and portable equipment. Full-scale common-mode rejection is specified at 84 dB, supporting rejection of common-mode noise in sensor, instrumentation, and industrial control circuits.
OPA743PA is implemented in CMOS technology and supports single-supply voltages up to 12 V, allowing operation from common 3.3 V, 5 V, and 12 V systems when the loop configuration and output-swing requirements permit. The manufacturer specifies the family over supply ranges extending to ±1.75 V through ±6 V for single and dual operation, providing flexibility across low-voltage instrumentation and higher-voltage analog interfaces.
Typical applications include sensor-signal conditioning, low-voltage data acquisition, audio and communication signal paths, LCD gamma-correction reference buffers, analog filters, and general-purpose buffering. The high output-current capability combined with 12 V operation makes the OPA743 particularly suitable for driving higher-capacitance loads and LCD reference networks when design limits are respected.
The primary design considerations are input common-mode range, output swing, load capacitance, and stability. Feedback-loop compensation should be checked for target gain and capacitive loading, while power-supply bypassing should be placed close to the supply pins. The manufacturer datasheet should be used to select operating points and confirm that signal amplitudes, load conditions, and package limits remain within specification.
This product page combines the OPA743PA family characteristics, package identification, application guidance, and practical design considerations into a concise engineering reference. It highlights the 7 MHz bandwidth, 10 V/µs slew rate, 84 dB common-mode rejection, rail-to-rail I/O operation, and 1.1 mA quiescent current that distinguish this general-purpose CMOS amplifier in practical analog-signal applications.
Alternativas directas para OPA743PA — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
OPA734PA
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
OPA735PA
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
OPA743PA Valores máximos y características eléctricas
| Number of Channels | 1 channel |
| Maximum Supply Voltage | 12 V |
| Single-Supply Operating Range | Up to 12 V |
| Dual-Supply Operating Range | ±6 V |
| Gain-Bandwidth Product | 7 MHz |
| Slew Rate | 10 V/µs |
| Corriente en reposo | 1.1 mA |
| Common-Mode Rejection Ratio | 84 dB |
| Input Type | Rail-to-rail |
| Tipo de salida | Rail-to-rail |
| Process Technology | CMOS |
| Número de pines | 8 pins |
| Encapsulado | 8-pin PDIP |
| Tipo de montaje | Through-hole |
| Product Type | Single CMOS operational amplifier |
Configuración de pines de OPA743PA
| Pin 1 | NC — Not connected |
| Pin 2 | IN- — Inverting input |
| Pin 3 | IN+ — Non-inverting input |
| Pin 4 | V- — Negative supply connection |
| Pin 5 | NC — Not connected |
| Pin 6 | OUT — Operational-amplifier output |
| Pin 7 | V+ — Positive supply connection |
| Pin 8 | NC — Not connected |
Aplicaciones típicas
OPA743PA es adecuado para 6 aplicacións: Sensor Signal Conditioning, Low-Voltage Data Acquisition, LCD Gamma-Correction Reference Buffer, Portable Analog Front End, Active Audio Signal Conditioning, Industrial Control Signal Buffer.
Sensor Signal Conditioning
OPA743PA fits sensor-conditioning stages that require signal amplification close to the supply rails. Its rail-to-rail input operation accepts a broad input range, while the 7 MHz gain-bandwidth product and 10 V/µs slew rate preserve useful bandwidth for moderately fast sensor signals. The 1.1 mA quiescent current also limits overhead in portable or distributed measurement systems. Configure the feedback network for the required closed-loop gain, verify common-mode rejection at the operating frequency, and place supply bypassing close to the device.
Recomendado
Low-Voltage Data Acquisition
OPA743PA is suitable for analog front ends in low-voltage data-acquisition equipment where both source impedance and signal bandwidth matter. Its CMOS implementation, 1.1 mA quiescent current, and 7 MHz gain-bandwidth product support low-power acquisition channels. The 84 dB common-mode rejection characteristic helps reduce unwanted common-mode signals in sensor and instrumentation systems. Select feedback components for the intended noise gain, check settling requirements for the acquisition bandwidth, and use short analog traces with a direct return path.
Recomendado
LCD Gamma-Correction Reference Buffer
OPA743PA is specifically suited to LCD gamma-correction reference buffering because the manufacturer highlights the combination of 12 V operation, high output-current capability, 7 MHz bandwidth, and 10 V/µs slew rate for this use. Rail-to-rail output operation can provide useful voltage range in reference networks, while the fast slew rate helps reproduce changing correction waveforms. Confirm the panel's channel count and reference impedance, evaluate capacitive loading, and verify that the required output-voltage and current levels remain within the amplifier's limits.
Recomendado
Portable Analog Front End
OPA743PA supports portable analog front ends where a 1.1 mA quiescent current is attractive but 7 MHz bandwidth and 10 V/µs slew rate are still useful. It can buffer sensors, implement active filters, or amplify low-level signals within systems powered from 3.3 V, 5 V, or other compatible supplies. The rail-to-rail input and output characteristics improve utilization of the available supply voltage. Designers should still account for output-swing limits, shutdown requirements, noise, and startup behavior when defining the complete low-power signal chain.
Recomendado
Active Audio Signal Conditioning
OPA743PA can amplify and buffer audio-frequency signals when the circuit requires more bandwidth than a general-purpose micropower amplifier. Its 7 MHz gain-bandwidth product and 10 V/µs slew rate support moderate audio-bandwidth and waveform demands, while the 1.1 mA quiescent current suits low-power audio equipment. A rail-to-rail output can increase signal range in a limited-voltage system. Confirm the required output swing, load impedance, channel count, distortion expectations, and stability with the selected feedback network.
Recomendado
Industrial Control Signal Buffer
OPA743PA is appropriate for buffering and scaling control signals in industrial systems requiring wider bandwidth than slow precision amplifiers. The 84 dB common-mode rejection ratio helps reject common-mode noise, while 1.1 mA quiescent current supports compact multi-channel designs. Its rail-to-rail input characteristic is useful when actuator or sensor signals span much of the available supply range. Verify noise immunity, output-current demand, temperature limits, and isolation requirements at the system level before using it in safety-critical control paths.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para OPA743PA — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto |
|---|---|
| Brand | Texas Instruments |
| Package | 8-pin PDIP |
| Channel Count | 1 channel |
| Maximum Single Supply | 12 V |
| Maximum Dual Supply | ±6 V |
| Gain-Bandwidth Product | 7 MHz |
| Slew Rate | 10 V/µs |
| Quiescent Current | 1.1 mA |
| Common-Mode Rejection Ratio | 84 dB |
| Input and Output | Rail-to-rail |
| Technology | CMOS |
Diferenciadores clave
- Combines moderate speed with low quiescent current (frente a Lower-speed general-purpose CMOS operational amplifiers)
- Uses rail-to-rail input and output operation (frente a Conventional fixed-common-mode operational amplifiers)
- Offers 84 dB common-mode rejection (frente a Low-cost amplifiers with unspecified CMRR)
Notas de diseño
Place the supply bypass capacitor and analog return connection as close as practical to the OPA743PA pins. Keep the high-frequency return path short and avoid routing sensitive input traces beside digital, switching, or power-conversion nets. The 7 MHz gain-bandwidth product means that even short PCB traces can become electrically significant at the upper operating frequencies, so use a compact layout and a solid ground plane when the amplifier is part of a mixed-signal board.
Do not treat rail-to-rail input and output as unlimited ranges. Verify the input common-mode limits, output swing, load current, and supply limits at the intended temperature. In particular, a 10 V/µs slew-rate rating does not guarantee low distortion for every large-amplitude waveform. Check the closed-loop gain, output amplitude, load, and compensation requirements together so that the selected OPA743PA configuration remains stable and accurate.
Estimated: OPA743PA quiescent power is approximately 13.2 mW when operated from a 12 V supply, calculated as 12 V multiplied by the specified 1.1 mA quiescent current. This estimate excludes output-stage dissipation caused by load current and voltage drop. Use the manufacturer datasheet for complete power-rating limits, and include regulator efficiency, amplifier dissipation, and temperature rise when designing a compact power system.
Select feedback resistors and capacitors for the intended closed-loop bandwidth rather than relying only on the 7 MHz gain-bandwidth product. Capacitive loading can reduce stability and alter the effective bandwidth, so use an isolation resistor near the output if the load is capacitive. For sensor inputs, account for source impedance, bias-current error, and common-mode range at the slowest and fastest input conditions.
Información de cumplimiento
No explicit compliance declarations for the OPA743PA ordering option were identified in the product and distributor results.